Stiffness Evaluation of Stressed-Skin Panels of Mixed Construction
Publication: Journal of Structural Engineering
Volume 123, Issue 8
Abstract
Stressed-skin panels (SSP) of mixed construction were made of various combinations of wood-based materials or lightweight concrete plates as the compression flange and a thin steel-sheet tension flange. An approximate method was developed for computing the stiffness of a SSP with flanges attached with various degrees of rigidity to spaced timber webs loaded in bending. Using this method, SSP deflection was calculated with a magnification factor, which reflected different slip moduli for joints between the webs and two flanges and by twice utilizing a two-layer model. The deflection predictions using this simple procedure compared well with the results of experiments performed on all panel types studied. However, when the load level exceeded approximately 60% of SSP capacity (which is well above the expected stress level in service), the predictions became less accurate. Finally, it was found that thin steel sheet tension flanges improve the total stiffness of the wood-based SSP.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Goodman, J. R. (1967). “Layered wood systems with interlayer slip,” PhD thesis, Univ. of California, Berkeley, Calif.
2.
Granholm, H. (1949). “Om sammansatta balkar och pelare med sä rskild hä nsyn till spikade trä konstruktioner.” Handling nr 88, Väg-och Vattenbyggnad, Byggnadsteknik 17, Chalmers Univ. of Technol., Göteborg, Sweden (in Swedish).
3.
Kliger, I. R. (1988). “Experimental study of stressed-skin panels under long-term loading.”Proc., IUFRO S5.02 Conf.
4.
Kliger, I. R. (1989). “Creep and durability of wood-joist floor systems.”Proc., IABSE Symp. on Durability of Struct., 285–290.
5.
Kliger, I. R. (1993). “Stressed-skin panels—shortand long-term behaviour.”Publ. 93:1, Chalmers Univ. of Technol., Div. of Steel and Timber Struct., Göteborg, Sweden.
6.
Kliger, I. R. (1996). “Flexural behavior of roof units for industrial buildings.”Proc., Int. Wood Engrg. Conf., Vol. 4, Omni Press, 161–168.
7.
Kliger, R., and Lecuyer, F. (1984). “Laboratory tests of glued joints.” Chalmers Univ. of Technol. Steel and Timber Struct., Int. skr. S 84:8, Göteborg, Sweden.
8.
Kliger, I. R., and Pellicane, P. J.(1995). “Prediction of creep properties of chipboard used in stressed-skin panels.”J. Testing and Evaluation, JTEVA, 23(6), 408–414.
9.
Kliger, I. R., and Pellicane, P. J.(1996a). “Time-dependent bending properties of lumber.”J. Testing and Evaluation, JTEVA, 24(3), 187–193.
10.
Kliger, I. R., and Pellicane, P. J.(1996b). “Shear properties of components used in stressed-skin panels.”J. Mat. in Civ. Engrg., 8(2), 77–82.
11.
Kliger, I. R., and Pellicane, P. J.(1997). “Stressed-skin panels of mixed construction—creep behavior.”J. Struct. Engrg., 123(7), 934–942.
12.
König, J. (1989). “Thin-walled wood-based flanges in composite beams.”CIB-W18A, Paper 22-10-3, Berlin, Germany.
13.
Kuenzi, E. W., and Wilkinson, T. E. (1972). “Composite beams—effects of adhesive or fastener rigidity.”Res. Paper FPL 152, U.S. Forest Prod. Lab., Madison, Wis.
14.
McCutcheon, W. J. (1977). “Method for predicting the stiffness of wood-joist system with partial composite action.”Res. Paper FPL 289, U.S. Forest Prod. Lab., Madison, Wis.
15.
McCutcheon, W. J.(1986). “Stiffness of framing members with partial composite action.”J. Struct. Engrg., 112(7), 1623–1637.
16.
Newmark, N. M., Siess, C. P., and Viest, I. M.(1951). “Tests and analysis of composite beams with incomplete interaction.”Proc., Soc. for Experimental Stress Anal., 9(1), 75–92.
17.
Norén, B. (1968). “Nailed joint—their strength and rigidity under short-term and long-term loading.” Byggforskningen 22, Stockholm, Sweden.
18.
Smith, I.(1980). “Series type solutions for built-up timber beams with semi-rigid connections.”Proc., Inst. of Civ. Engrg., 2(69), 707–719.
19.
Wright, H. D., and Oduyemi, T. O. S.(1991). “Partial interaction analysis of double skin composite beams.”J. Constr. Steel Res., 19(4), 253–283.
Information & Authors
Information
Published In
Copyright
Copyright © 1997 American Society of Civil Engineers.
History
Published online: Aug 1, 1997
Published in print: Aug 1997
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.