Tests on Shear Capacity of Reinforced Concrete
Publication: Journal of Structural Engineering
Volume 121, Issue 11
Abstract
The purpose of this research is to contribute to the definition of maximum carrying capacity and rational reinforcement schemes for structures such as deep beams, corbels, and dapped-end beams. The research included laboratory testing of 28 prismatic beam samples with a higher percentage of steel than currently permitted in design practice. The tests revealed that the nominal shear capacity may significantly exceed the current limits of both the American and Canadian codes if proper reinforcement is provided. The ratio of nominal shear stress to the compressive strength of concrete ( v u /f) can be as much as 0.42 when horizontal reinforcement is used, and 0.85 when a sufficient inclined reinforcement is provided. Strut and tie models, composed of multiple compression struts and tension ties corresponding to the configuration of the reinforcement, were used to analyze the test results. In all cases, the strut and tie models rendered results comparable with those from the laboratory tests. The ultimate shear capacity may be governed either by the compression struts (concrete) or the tension ties (steel). The maximum capacity occurs when the amount of reinforcement at least corresponds with the balanced condition, where the capacity of the tension ties is equal to, or greater than, that of the compression struts.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
“Building requirements for reinforced concrete.” (1983). ACI 318-83, American Concrete Institute (ACI), Detroit, Mich.
2.
Collins, M. P., and Mitchell, D.(1986). “A rational approach to shear design—the 1984 Canadian provisions.”J. Am. Concrete Inst., 83(4), 614–623.
3.
“Design of concrete structures for buildings.” (1984). CAN3-A23.3-M84, Can. Standards Assoc. (CSA), Toronto, Ont., Canada.
4.
Kriz, L. B., and Raths, C. H.(1965). “Connections in precast concrete structures—strength of corbels.”PCI J., 10(1), 16–61.
5.
Leonhardt, F., and Walther, R. (1961). “Beitrage zur Behandlung der Schubprobleme im Stahlbetonbau.” Beton und Stahlbetonbau, Hefte 12/1961, 2, 3, 5, 7/1962 (in German).
6.
Mattock, A. H.(1976). “Design proposals for reinforced concrete corbels.”PCI J., 21(3), 18–42.
7.
Mattock, A. H., and Chan, T. C. (1979). “Design and behavior of dapped-end beams.”PCI J., 28–45.
8.
Mattock, A. H., Chen, K. C., and Soongswang, K.(1976). “The behavior of reinforced concrete corbels.”PCI J., 21(2), 52–77.
9.
Mattock, A. H., and Hawkins, N. M.(1972). “Shear transfer in reinforced concrete—recent research.”PCI J., 16(2), 55–75.
10.
Mattock, A. H., Johel, L. S., and Chow, H. C.(1975). “Shear transfer in reinforced concrete with moment or tension acting across the shear plane.”PCI J., 20(4), 76–93.
11.
Mörsch, E. (1909). Concrete-steel construction, 3rd Ed., E. P. Goodrich, translator, McGraw-Hill Book Co., Inc., New York, N.Y.
12.
Schlaich, J., Schater, K., and Jennewein, M.(1987). “Towards a consistent design of reinforced concrete structures.”J. Prestressed Concrete Inst., 32(3), 74–150.
13.
Zielinski, Z. A. (1957). “Prefabrykowane betonowe dzwigary sprezone.”Precast prestressed concrete girders, Arkady, Warsaw, Poland, 1–309, (in Polish).
14.
Zielinski, Z. A. (1958). “Entwurfs—und Verwendungsprobleme wirtschaftlicher Spannbetontragern.”Proc., Paper No. 17, Federation Internationale de la Precontraine (FIP), Berlin, Germany, 1–6.
15.
Zielinski, Z. A. (1967). “Behavior and ultimate strength of rectangular reinforced concrete beams in bending and higher shear.”Engrg. School Bull. No. 81, Dept. of Engrg. Res., North Carolina State Univ., Raleigh, N.C., 1–70.
16.
Zielinski, Z. A. (1971). “A new approach to ultimate strength of reinforced concrete beam in inclined cracking and reduction of web reinforcement in bridge girders.”Proc., SP26 2nd Int. Symp.—Concrete Bridge Des., Am. Concrete Inst. (ACI), Detroit, Mich., 411–456.
17.
Zielinski, Z. A., and Abdulezar, A.(1977). “Ultimate strength in diagonal splitting of reinforced concrete thin wall panels.”Can. J. Civ. Engrg., Ottawa, Canada, 4(2), 226–239.
Information & Authors
Information
Published In
Copyright
Copyright © 1995 American Society of Civil Engineers.
History
Published online: Nov 1, 1995
Published in print: Nov 1995
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.