Statistical Study on Compression Flange Plates
Publication: Journal of Structural Engineering
Volume 109, Issue 2
Abstract
This paper summarizes the reduced ultimate strength of the compression flange of plate girders containing initial deflection. The major findings are as follows: There is no interrelation between the maximum initial deflection and plate dimension such as width, thickness or width‐thickness ratio of the flange. The slenderness parameter of plate, R, a function of the widththickness ratio, and the aspect ratio, are the two factors reducing the ultimate strength. The ultimate strength is minimum with the aspect ratio in the range of 2 to 3. However, the reducing effect does not increase when the aspect ratio is beyond 3. Among the three initial deflection modes—plate bending, cylindrical bending and simple twisting, the simple twisting has the least effect. is the most sensitive value to the initial deflection in reducing the ultimate strength. A procedure has been established to obtain expected and theoretical ultimate strength by a probability density function through Weibull distribution or Gamma distribution.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Beulsicherhei tsnachweise für Platten, Deutscher Ausschuβ für Stahlbau, Richtlinie 012 (DASt Ri012), 1978.
2.
Ellis, L. G., “Statistical Appraisal of the Measured Deformations in Several Steel Box Girder Bridges,” Journal of Strain Analysis, Vol. 12, No. 2, 1977, pp. 97–106.
3.
European Recommendation for Steel Constructions, ECCS, 1981.
4.
Kato, T., Ishioka, H., and Nakanishi, M., “Initial Imperfections of π‐girder Bridges with Wide Steel Deck,” The Bridge and Foundation Engineering, July, 1979, pp. 38–43 (in Japanese).
5.
Kitada, T., “Study on Ultimate Strength of Steel Plates and Stiffened Plates under Compression,” thesis presented to the Osaka University, at Osaka, Japan, in 1980, in partial fulfillment of the requirements for the degree of Doctor of Engineering.
6.
Komatsu, S., Kitada, T., and Miyazaki, S., “Elasto‐Plastic Analysis of Compressed Plate with Residual Stress and Initial Deflection,” Proceedings of Japan Society of Civil Engineers (JSCE), No. 244, Dec., 1975, pp. 1–14 (in Japanese).
7.
Komatsu, S., Nara, S., and Kitada, T., “Elasto‐Plastic Analysis of Orthogonally Stiffened Plates with Initial Imperfections under Uniaxial Compression,” Computers & Structures, Vol. 11, No. 5, 1980, pp. 429–437.
8.
Komatsu, S., and Kitada, T., “Ultimate Strength Characteristics of Outstanding Steel Plates with Initial Imperfections,” Proceedings of JSCE, No. 314, Oct., 1981, pp. 15–27 (in Japanese).
9.
Leonhardt, F., and Hommel, D., “The Necessity of Quantifying Imperfections of All Structural Members for Stability of Box Girders,” Steel Box Girder Bridges, P. Cartledge, ed., The Institution of Civil Engineers, London, England, 1973, pp. 5–13.
10.
Maquoi, R., “Essais de détermination des fléches initials des panneaux radis des grands ponts en caisson,” IABSE publication, No. 31‐2, 1971, pp. 141–151.
11.
Massonnet, C., “Tolerances in Steel Plated Structures,” IABSE Periodica, 3, s‐14, Aug., 1980.
12.
ÖNORM B4600/4, Stahlbau, Stabilitätsnachweis, Grundfälle, 1, Dec., 1972.
13.
Proposed Design Specifications for Steel Box Girder Bridges, Final Report, Federal Highway Administration, Jan., 1980.
14.
Specifications for Highway Bridges, Part II, Steel bridges, Japan Road Association, 1973.
15.
Specifications for Highway Bridges, Part II, Steel bridges, Japan Road Association, 1980.
16.
“Statistical Study on the Initial Deformations and the Ultimate Strength of Steel Bridge Members,” Committee of Initial Deflection Measurement, Journal of Society of Steel Construction of Japan, Vol. 16, No. 179, 1980, pp. 10–43 (in Japanese).
17.
Steel, Concrete and Composite, Part 6 Specification for Material and Workmanship, Steel, British Standards Institution BS5400, 1980.
18.
Thompson, J. D., “Control of Distortion due to Welding and the Additional Cost Involved,” Journal of Strain Analysis, Vol. 12, No. 2, 1977, pp. 148–152.
19.
Tordoff, D., “Workmanship and Fabrication,” The Design of Steel Bridges, K. C. Rockey, and H. R. Evans, ed., Gradana, London, England, 1981, pp. 73–82.
Information & Authors
Information
Published In
Copyright
Copyright © 1983 ASCE.
History
Published online: Feb 1, 1983
Published in print: Feb 1983
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.