Probabilistic Simulation Studies for Repetitive Construction Processes
Publication: Journal of Construction Engineering and Management
Volume 116, Issue 4
Abstract
Before full adaptation of simulation techniques for the analysis and design of construction operations can be implemented, the appropriate statistical tools must be understood and applied as part of the simulation experiment. Most simulation models in construction can be treated as stochastic models. The proper analysis of such models requires: (1) Application of input modeling techniques; (2) appropriate analysis of output parameters of concern based on multiple runs; and (3) validation and verification of the results. This paper describes techniques applicable to the simulation of repetitive construction operations and presents a practical example application to demonstrate how they can be applied. Procedures for selecting input models, methods for solving for the parameters of selected distributions, and goodness‐of‐fit testing for construction data are reviewed. The discussions on output analysis were limited to simulation output that is normal because it is frequently encountered in construction simulation. Methods for checking the normality of output data, building confidence intervals for various output parameters, and validation of simulation models are also addressed.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
AbouRizk, S. M. (1988). “Statistical considerations in simulating construction operations.” Independent Research Study Report, Division of Construction Engineering and Management, Purdue Univ., West Lafayette, Ind.
2.
AbouRizk, S. M. (1989). BetaFit user's guide. Division of Construction Engineering and Management, Purdue Univ., West Lafayette, Ind.
3.
AbouRizk, S., Hijazi, A., and Halpin, D. W. (1989). “Effect of input modeling on simulation output.” Proc., Sixth Conf. on Computing in Civ. Engrg., ASCE, 605–612.
4.
Adrian, J., and Boyer, L. T. (1976). “Modeling method‐productivity.” J. Constr. Div., ASCE, 103(3), 154–168.
5.
Banks, J., and Carson, J. S. (1984). Discrete‐event system simulation. Prentice‐Hall, Inc., Englewood Cliffs, N.J.
6.
Bernold, L. E. (1985). “Productivity transient in construction processes,” thesis presented to the Georgia Institute of Technology, at Atlanta, Ga., in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
7.
Biles, W. E. (1987). “Introduction to simulation.” Proc., 1987 Winter Simulation Conference, American Statistical Assoc., 7–15.
8.
Cottrell, G. B. (1989). Class report: Productivity study of indoor training facility. Division of Construction Engineering and Management, Purdue Univ., West Lafayette, Ind.
9.
Dabbas, M. A., and Halpin, D. W. (1982). “Integrated project and process management.” J. Constr. Div., ASCE, 108(3), 361–374.
10.
Debrota, D., et al. (1988). “Visual interactive fitting of probability distributions.” Simulation, 52, 199–205.
11.
Fishman, G. S. (1973). Concepts and methods in discrete‐event digital simulation. John Wiley, New York, N.Y.
12.
Hahn, G. J., and Shapiro, S. S. (1967). Statistical models in engineering, John Wiley and Sons, New York, N.Y.
13.
Halpin, D. W. (1973). “An investigation of the use of simulation networks for modeling construction operations,” thesis presented to the University of Illinois, at Urbana‐Champaign, Ill., in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
14.
Halpin, D. W. (1977). “CYCLONE: Method for modeling of job site processes.” J. Constr. Div., ASCE, 103(3), 489–499.
15.
Halpin, D. W. (1989). Microcyclone user's manual. Division of Construction Engineering and Management, Purdue Univ., West Lafayette, Ind.
16.
Halpin, D. W., and Woodhead, R. W. (1976). Design of construction and process operations. John Wiley and Sons, New York, N.Y.
17.
Hijazi, A. M. (1989). “Simulation analysis of linear construction processes,” thesis presented to Purdue University, at West Lafayette, Ind., in partial fulfillment of the requirements for the degree of Doctor of Philosophy.
18.
Ioannou, P. G. (1989). UM‐CYCLONE user's guide. Department of Civil Engineering, The Univ. of Michigan, Ann Arbor, Mich.
19.
Kelton, D. W. (1986). “Statistical design and analysis.” Proc. 1986 Winter Simulation Conf., Washington, D.C., 45–51.
20.
Law, A. M., and Kelton, W. D. (1982). Simulation modeling and analysis. McGraw‐Hill, New York, N.Y.
21.
Law, A. M., and McComas, M. G. (1986). “Pitfalls in the simulation of manufacturing systems.” Proc. 1986 Winter Simulation Conf., Washington, D.C., 539–542.
22.
Law, A. M., and Vincent, S. G. (1985). UniFit user's guide. Simulation Modeling and Analysis Co., Tucson, Ariz.
23.
Lluch, J., and Halpin, D. W. (1982). “Construction operations and microcomputers.” J. Constr. Div., ASCE, 108(1), 129–145.
24.
Paulson, B. C., Jr. (1978). “Interactive graphics for simulating construction operations.” J. Constr. Div., ASCE, 104(1), 69–76.
25.
Pearson, E. S., D'Agostino, R. B., and Bowman, K. O. (1977). “Test for departure from normality: Comparison of powers.” Biometrica, 64, 231–246.
26.
Pritsker, A. A. B. (1985). Introduction to simulation and SLAM‐II. John Wiley, New York, N.Y.
27.
Riggs, L. S. (1980). “Sensitivity analysis of construction operations.” J. Tech. Councils, ASCE, 106(1), 145–163.
28.
Riggs, L. S. (1989). “Interactive graphing of simulation networks.” J. Comput. Civ. Engrg., ASCE, 3(2), 173–182.
29.
Royston, J. P. (1982). “The W. test for normality.” Appl. Statistics, 31, 176–180.
30.
Schmeiser, B. (1982). “Batch size effects in the analysis of simulation output.” Operations Res., 30(3), 556–568.
31.
Schmeiser, B., and Wilson, J. R. (1988). “Building simulation metamodels: Diagnostic check for normality.” FORTRAN program developed at Purdue Univ., West Lafayette, Ind.
32.
Shapiro, S. S., and Wilk, M. B. (1965). “An analysis of variance test for normality.” Biometrica, 52, 591–611.
33.
Sturges, H. A. (1926). “The choice of class intervals.” J. Am. Statistical Assoc., 21, 65–66.
34.
Swain, J., Venkatraman, S., and Wilson, J. (1988). “Least squares estimation of distribution functions in Johnson's translation system.” J. Statist. Comput. Simul., 29, 271–297.
35.
Venkatraman, S., and Wilson, J. R. (1988). “Modeling univariate populations with Johnson's translation systems—Description of the FITTR1 software.” Research Memorandum No. 87‐21, Purdue Univ., West Lafayette, Ind.
36.
Welch, P. D. (1983). “The statistical analysis of simulation results.” Computer performance modeling handbook, S. S. Lavenberg, ed., Academic Press, New York, N.Y.
37.
Wilson, J. R. (1984). “Statistical aspects of simulation.” Operational Research '84: Proc., 10th Annual Int. Conf. on Operational Res., J. P. Brans, ed., Elsevier Science Publishers B. V., Amsterdam, The Netherlands, 921–937.
Information & Authors
Information
Published In
Journal of Construction Engineering and Management
Volume 116 • Issue 4 • December 1990
Pages: 575 - 594
Copyright
Copyright © 1990 ASCE.
History
Published online: Dec 1, 1990
Published in print: Dec 1990
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.