Design of Gusset Plates and Interface Welds of SCBF Systems with Braces Buckling In-Plane
Publication: Journal of Structural Engineering
Volume 150, Issue 10
Abstract
The design of connections of gusset plates, beams, and columns of concentrically braced frame systems is typically based on the forces generated by brace actions without considering the frame actions. This may result in underestimating the design force demand on gusset plates, potentially leading to the failure of interface weld connections at higher lateral drift levels. The present study aims to estimate the force demands at the connection interfaces, typically about a 2% story-drift ratio (SDR), corresponding to the design-level ground motions for braced frame systems. The study considers both the forces of frame and brace action on the corner gusset plate in the design process. It also aims to develop suitable design recommendations to prevent premature weld failures at higher lateral drift. High-fidelity finite-element models of in-plane buckling (IPB) braced frame systems are developed and analyzed under various loading modes. A current standard design method to determine the interface weld size was found to be inadequate to prevent premature failures at the higher drift levels. This is primarily due to the accumulation of the plastic strain at the tip of the gusset at higher drift. The out-of-plane bending of the gusset plate due to geometric imperfection was also found to contribute toward the development of high plastic strain at the tips of gusset plates. Three different connection configurations are considered and analyzed under critical cyclic loading conditions. Finally, design recommendations are presented to avoid stress concentration and premature fracture of gusset plate connections of the IPB braced frame systems.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or codes that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The financial assistance received from the Ministry of Education, Government of India (Grant No. 35-5/2017-TS-I) toward the Prime Minister Research Fellowship of the first author is gratefully acknowledged.
References
ABAQUS. 2017. ABAQUS analysis user’s manual version 6.17-1. Providence, RI: Dassault Systems Simulia.
AIJ (Architectural Institute of Japan). 2016. Recommendations for design of connections in steel structures. [In Japanese.] Tokyo: AIJ.
AISC. 1992. Manual of steel construction: Allowable stress design. 9th ed. Chicago: AISC.
AISC. 2014. Vertical bracing connections: Analysis and design. AISC design guide 29. Chicago: AISC.
AISC. 2016. Seismic provisions for structural steel buildings. ANSI/AISC 341-16. Chicago: AISC.
AISC. 2022. Seismic provisions for structural steel buildings. ANSI/AISC 341-22. Chicago: AISC.
ASCE. 2022. Minimum design loads and associated criteria for buildings and other structures. ASCE/SEI 7-22. Reston, VA: ASCE.
Astaneh-Asl, A. 1989. “Simple methods for design of steel gusset plates.” In Proc., ASCE Structures Congress, 345–354. Reston, VA: ASCE.
Astaneh-Asl, A. 1998. Seismic behavior and design of gusset plates. Moraga, CA: Structural Steel Educational Council.
Bao, Y., and T. Wierzbicki. 2005. “On the cut-off value of negative triaxiality for fracture.” Eng. Fract. Mech. 72 (7): 1049–1069. https://doi.org/10.1016/j.engfracmech.2004.07.011.
BCJ (Building Center of Japan). 2007. Commentary of structure design provisions for buildings. [In Japanese.] Tokyo: AIJ.
Chou, C.-C., and J.-H. Liu. 2012. “Frame and brace action forces on steel corner gusset plate connections in buckling-restrained braced frames.” Earthquake Spectra 28 (2): 531–551. https://doi.org/10.1193/1.4000007.
Cui, Y., H. Asada, S. Kishiki, and S. Yamada. 2012. “Ultimate strength of gusset plate connections with fillet welds.” J. Constr. Steel Res. 75 (Aug): 104–115. https://doi.org/10.1016/j.jcsr.2012.03.010.
Cui, Y., X. Xu, T. C. Becker, and W. Zhang. 2021. “Incorporating frame action into seismic design of gusset plates.” J. Struct. Eng. 147 (3): 4021005. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002959.
EERI (Earthquake Engineering Research Institute). 2012. Performance of engineered structures in the Mw 9.0 Tohoku, Japan, earthquake of March 11, 2011. Oakland, CA: EERI.
Fell, B. V., A. M. Kanvinde, G. G. Deierlein, and A. T. Myers. 2009. “Experimental investigation of inelastic cyclic buckling and fracture of steel braces.” J. Struct. Eng. 135 (1): 19–32. https://doi.org/10.1061/(ASCE)0733-9445(2009)135:1(19).
FEMA. 2000. Recommended seismic design criteria for new steel moment-frame buildings. FEMA-350. Washington, DC: FEMA.
Imanpour, A., R. Tremblay, A. Davaran, C. Stoakes, and L. A. Fahnestock. 2016. “Seismic performance assessment of multitiered steel concentrically braced frames designed in accordance with the 2010 AISC seismic provisions.” J. Struct. Eng. 142 (12): 04016135. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001561.
Jia, L.-J., T. Ikai, K. Shinohara, and H. Ge. 2016. “Ductile crack initiation and propagation of structural steels under cyclic combined shear and normal stress loading.” Constr. Build. Mater. 112 (Jun): 69–83. https://doi.org/10.1016/j.conbuildmat.2016.02.171.
Krawinkler, H. 1992. Guidelines for cyclic seismic testing of components of steel structures. Redwood City, CA: Applied Technology Council.
Lee, C.-H. 2002. “Seismic design of rib-reinforced steel moment connections based on equivalent strut model.” J. Struct. Eng. 128 (9): 1121–1129. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:9(1121).
Lehman, D. E., C. W. Roeder, D. Herman, S. Johnson, and B. Kotulka. 2008. “Improved seismic performance of gusset plate connections.” J. Struct. Eng. 134 (6): 890–901. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:6(890).
Lemaitre, J., and J.-L. Chaboche. 1990. Mechanics of solid materials. Cambridge, UK: Cambridge University Press.
Lumpkin, E. J., P.-C. Hsiao, C. W. Roeder, D. E. Lehman, C.-Y. Tsai, A.-C. Wu, C.-Y. Wei, and K.-C. Tsai. 2012. “Investigation of the seismic response of three-story special concentrically braced frames.” J. Constr. Steel Res. 77 (Oct): 131–144. https://doi.org/10.1016/j.jcsr.2012.04.003.
Muir, L. S. 2008. “Designing compact gussets with the uniform force method.” Eng. J. 45 (1): 13–20. https://doi.org/10.62913/engj.v45i1.928.
Myers, A. T. 2009. Testing and probabilistic simulation of ductile fracture initiation in structural steel components and weldments. Technical Rep. No. 170. Stanford, CA: John A. Blume Earthquake Engineering Center, Stanford Univ.
Okazaki, T., D. G. Lignos, T. Hikino, and K. Kajiwara. 2013. “Dynamic response of a chevron concentrically braced frame.” J. Struct. Eng. 139 (4): 515–525. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000679.
Patra, P., and D. R. Sahoo. 2021. “Influence of types of end connections and detailing of end-protected zones on seismic performance of SCBFs.” J. Struct. Eng. 147 (1): 04020307. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002885.
Patra, P., and D. R. Sahoo. 2023. “Stability assessment and development of design criteria for SCBF systems with in-plane buckling braces.” Earthquake Eng. Struct. Dyn. 52 (4): 1136–1160. https://doi.org/10.1002/eqe.3808.
Ricker, D. T. 1992. Value engineering and steel economy. Moraga, CA: Structural Steel Educational Council.
Roeder, C. W., E. J. Lumpkin, and D. E. Lehman. 2011. “A balanced design procedure for special concentrically braced frame connections.” J. Constr. Steel Res. 67 (11): 1760–1772. https://doi.org/10.1016/j.jcsr.2011.04.016.
Sabelli, R., C. W. Roeder, and J. F. Hajjar. 2013. Seismic design of steel special concentrically braced frame systems. Gaithersburg, MD: National Earthquake Hazards Reduction Program.
Sabelli, R., and B. Saxey. 2021. “Design for local member shear at brace and diagonal-member connections: Full-height and chevron gussets.” Eng. J.-Am. Inst. Steel Constr. 58 (1): 45–78. https://doi.org/10.62913/engj.v58i1.1218.
Sabelli, R., and B. Saxey. 2023. “Closure: Design for local member shear at brace and diagonal-member connections: Full-height and chevron gussets.” Eng. J. 60 (3): 123–127. https://doi.org/10.62913/engj.v60i3.1211.
Seki, A., K. Inoue, T. Okazaki, S. Hashioka, and H. Asada. 2022. “Seismic performance of steel chevron braced frames designed according to Japanese practice.” J. Constr. Steel Res. 189 (Feb): 107066. https://doi.org/10.1016/j.jcsr.2021.107066.
Sen, A. D. 2018. “New methods for seismic performance evaluation and retrofit of nonductile concentrically braced frames.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Univ. of Washington.
Sen, A. D., D. Sloat, R. Ballard, M. M. Johnson, C. W. Roeder, D. E. Lehman, and J. W. Berman. 2016. “Experimental evaluation of the seismic vulnerability of braces and connections in older concentrically braced frames.” J. Struct. Eng. 142 (9): 4016052. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001507.
Sen, A. D., M. A. Swatosh, R. Ballard, D. Sloat, M. M. Johnson, C. W. Roeder, D. E. Lehman, and J. W. Berman. 2017. “Development and evaluation of seismic retrofit alternatives for older concentrically braced frames.” J. Struct. Eng. 143 (5): 4016232. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001738.
Simpson, B. G., and S. A. Mahin. 2018. “Experimental and numerical evaluation of older chevron concentrically braced frames with hollow and concrete-filled braces.” J. Struct. Eng. 144 (3): 4018007. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001988.
Thornton, W. A. 1991. “On the analysis and design of bracing connections.” In Proc., AISC National Steel Construction Conf., 21–26. Chicago: AISC.
Thornton, W. A. 1992. Designing for cost efficient fabrication. Moraga, CA: Structural Steel Educational Council.
Thornton, W. A., and L. S. Muir. 2008. “Vertical bracing connections in the seismic regime.” In Proc., Connections VI. Chicago: AISC.
Tsai, C.-Y., K.-C. Tsai, P.-C. Lin, W.-H. Ao, C. W. Roeder, S. A. Mahin, C.-H. Lin, Y.-J. Yu, K.-J. Wang, and A.-C. Wu. 2013. “Seismic design and hybrid tests of a full-scale three-story concentrically braced frame using in-plane buckling braces.” Earthquake Spectra 29 (3): 1043–1067. https://doi.org/10.1193/1.4000165.
Uriz, P. 2005. “Towards earthquake resistant design of concentrically braced steel structures.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Univ. of California.
von Mises, R. 1913. “Mechanik der festen Körper im plastisch-deformablen Zustand.” Nachrichten von der Gesellschaft der Wissenschaften zu Göttingen, Mathematisch-Physikalische Klasse 1913: 582–592.
Williams, G. C., and R. M. Richard. 1996. “Analysis and design of large diagonal bracing connections.” Struct. Eng. Rev. 1 (8): 1–27. https://doi.org/10.1016%2F0952-5807(94)00042-5.
Xu, F., T.-M. Chan, T. Sheehan, and L. Gardner. 2020. “Prediction of ductile fracture for circular hollow section bracing members under extremely low cycle fatigue.” Eng. Struct. 214 (Jul): 110579. https://doi.org/10.1016/j.engstruct.2020.110579.
Yoo, J.-H., D. E. Lehman, and C. W. Roeder. 2008. “Influence of connection design parameters on the seismic performance of braced frames.” J. Constr. Steel Res. 64 (6): 607–623. https://doi.org/10.1016/j.jcsr.2007.11.005.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 150 • Issue 10 • October 2024
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Jul 7, 2023
Accepted: May 3, 2024
Published online: Jul 29, 2024
Published in print: Oct 1, 2024
Discussion open until: Dec 29, 2024
ASCE Technical Topics:
- Analysis (by type)
- Bracing
- Connections (structural)
- Construction engineering
- Construction methods
- Continuum mechanics
- Dynamic loads
- Dynamics (solid mechanics)
- Earthquake engineering
- Engineering fundamentals
- Engineering mechanics
- Failure analysis
- Frames
- Geotechnical engineering
- Plates
- Seismic loads
- Solid mechanics
- Structural dynamics
- Structural engineering
- Structural members
- Structural systems
- Welded connections
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.