Transport Properties and Deicing Salt Resistance of Blended Ultrahigh-Performance Concrete
Publication: Journal of Cold Regions Engineering
Volume 38, Issue 2
Abstract
Premature degradation of concrete, caused by frost damage, has been associated with inadequate transport properties and poor resistance to deicing salt. In this study, transport properties and deicing salt resistance of various kinds of ultrahigh-performance concrete (UHPC) containing Type V portland cement, fly ash, and microsilica were investigated. Seven combinations of cementitious materials (one reference, three binary, and three ternary) were used to batch UHPCs using a water-to-cementitious material ratio (w/cm) of 0.21. The aggregate-to-cementitious material ratio (Va/Vcm) of 1.20 was kept constant for all mixtures. The investigated transport properties included water absorption, volume of permeable voids, water penetration, rapid chloride penetration, and surface resistivity. The transport properties of the plain UHPCs were also compared to those of the corresponding steel fiber–reinforced UHPCs. The test results showed that the transport properties and deicing salt resistance of the studied binary and ternary UHPCs improved with the inclusion and increases in microsilica, replacing a portion of cement. The addition of steel fiber had a minor effect on strength and transport properties and a moderate increase in deicing salt resistance of the studied UHPCs. While rapid chloride penetration and surface resistivity tests were found appropriate to assess chloride transport through the studied plain UHPCs, both tests were deemed unsuitable for the companion steel fiber–reinforced UHPCs.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some data that support the findings of this study are available from the corresponding author upon reasonable request. These data include tabular results, graphical results, and photographs of the laboratory tests.
Acknowledgments
This study was funded by the US Department of Transportation through the University Transportation Center (Grant No. GR09035). Thanks are extended to the suppliers who donated materials.
References
AASHTO. 2019. Standard method of test for surface resistivity indication of concrete’s ability to resist chloride ion penetration. AASHTO T 358. Washington, DC: AASHTO
Abbas, S., A. M. Soliman, and M. L. Nehdi. 2015. “Exploring mechanical and durability properties of ultra-high performance concrete incorporating various steel fiber lengths and dosages.” Constr. Build. Mater. 75: 429–441. https://doi.org/10.1016/j.conbuildmat.2014.11.017.
Abellán García, J., J. Fernandez Gómez, and N. Torres Castellanos. 2022. “Properties prediction of environmentally friendly ultra-high-performance concrete using artificial neural networks.” Eur. J. Environ. Civ. Eng. 26 (6): 2319–2343. https://doi.org/10.1080/19648189.2020.1762749.
Acker, P., and M. Behloul. 2004. “Ductal® technology: A large spectrum of properties, a wide range of applications.” In Proc., Int. Symp. on Ultra High Performance Concrete, 11–23. Kassel, Germany: Kassel Univ. Press GmbH
Ahlborn, T. M., E. J. Peuse, and D. L. Misson. 2008. Ultra-high performance concrete for Michigan bridges, material performance: Phase I. RC-1525. Lansing, MI: Michigan Dept. of Transportation.
Ahlborn, T. T. M., D. K. Harris, D. L. Misson, and E. J. Peuse. 2011. “Characterization of strength and durability of ultra-high-performance concrete under variable curing conditions.” Transp. Res. Rec. 2251 (1): 68–75. https://doi.org/10.3141/2251-07.
Akhnoukh, A. K., and C. Buckhalter. 2021. “Ultra-high-performance concrete: Constituents, mechanical properties, applications and current challenges.” Case Stud. Constr. Mater. 15: e00559. https://doi.org/10.1016/j.cscm.2021.e00559.
Alkaysi, M., S. El-Tawil, Z. Liu, and W. Hansen. 2016. “Effects of silica powder and cement type on durability of ultra high performance concrete (UHPC).” Cem. Concr. Compos. 66: 47–56. https://doi.org/10.1016/j.cemconcomp.2015.11.005.
Arora, A., A. Almujaddidi, F. Kianmofrad, B. Mobasher, and N. Neithalath. 2019. “Material design of economical ultra-high performance concrete (UHPC) and evaluation of their properties.” Cem. Concr. Compos. 104: 103346. https://doi.org/10.1016/j.cemconcomp.2019.103346.
ASTM. 2013. Standard test method for density, absorption, and voids in hardened concrete. ASTM C642. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard specification for steel fibers for fiber-reinforced concrete. ASTM A820/A820M. West Conshohocken, PA: ASTM.
ASTM. 2017. Standard practice for fabricating and testing specimens of ultra-high performance concrete. ASTM C1856/C1856M. West Conshohocken, PA: ASTM.
ASTM. 2019. Standard test method for electrical indication of concrete’s ability to resist chloride ion penetration. ASTM C1202-12. West Conshohocken, PA: ASTM.
ASTM. 2021a. Standard specification for flow table for use in tests of hydraulic cement. ASTM C230/C230M-14. West Conshohocken, PA: ASTM.
ASTM. 2021b. Standard test method for compressive strength of cylindrical concrete specimens. ASTM C39/C39M-12. West Conshohocken, PA: ASTM.
Bajaber, M. A., and I. Y. Hakeem. 2021. “UHPC evolution, development, and utilization in construction: A review.” J. Mater. Res. Technol. 10: 1058–1074. https://doi.org/10.1016/j.jmrt.2020.12.051.
Birchall, J. D., A. J. Howard, and K. Kendall. 1981. “Flexural strength and porosity of cements.” Nature 289 (5796): 388–390. https://doi.org/10.1038/289388a0.
Bonneau, O., C. Poulin, M. Dugat, and P. C. A. Tcin. 1996. “Reactive powder concretes: From theory to practice.” Concr. Int. 18 (4): 47–49.
BSI (British Standards Institution). 2000. Depth of penetration of water under pressure. BS EN-12390-8. London: BSI.
Bunnori, N. M., A. H. Alani, A. T. Noaman, M. M. Johari, and T. A. Majid. 2020. “Relationships between compressive strength and transport properties of ultrahigh-strength green concrete utilizing ternary-blended binder.” J. Mater. Civ. Eng. 32 (3): 04020011. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003071.
Cigna, R., E. Proverbio, and G. Rocchini. 1993. “A study of reinforcement behaviour in concrete structures using electrochemical techniques.” Corros. Sci. 35 (5–8): 1579–1584. https://doi.org/10.1016/0010-938X(93)90387-V.
Dong, Y. 2018. “Performance assessment and design of ultra-high performance concrete (UHPC) structures incorporating life-cycle cost and environmental impacts.” Constr. Build. Mater. 167: 414–425. https://doi.org/10.1016/j.conbuildmat.2018.02.037.
El-Dieb, A. S. 2009. “Mechanical, durability and microstructural characteristics of ultra-high-strength self-compacting concrete incorporating steel fibers.” Mater. Des. 30 (10): 4286–4292. https://doi.org/10.1016/j.matdes.2009.04.024.
El-Enein, S. A., M. F. Kotkata, G. B. Hanna, M. Saad, and M. M. Abd El Razek. 1995. “Electrical conductivity of concrete containing silica fume.” Cem. Concr. Res. 25 (8): 1615–1620. https://doi.org/10.1016/0008-8846(95)00156-5.
Graybeal, B. A. 2006. Material property characterization of ultra-high performance concrete. FHWA-HRT-06-103. Washington, DC: Federal Highway Administration, Office of Infrastructure Research and Development.
Guzmán, S., J. C. Gálvez, and J. M. Sancho. 2011. “Cover cracking of reinforced concrete due to rebar corrosion induced by chloride penetration.” Cem. Concr. Res. 41 (8): 893–902. https://doi.org/10.1016/j.cemconres.2011.04.008.
Haber, Z. B., J. F. Munoz, I. De la Varga, and B. A. Graybeal. 2018. “Bond characterization of UHPC overlays for concrete bridge decks: Laboratory and field testing.” Constr. Build. Mater. 190: 1056–1068. https://doi.org/10.1016/j.conbuildmat.2018.09.167.
Hasnat, A., and N. Ghafoori. 2021a. “Properties of ultra-high performance concrete using optimization of traditional aggregates and pozzolans.” Constr. Build. Mater. 299: 123907. https://doi.org/10.1016/j.conbuildmat.2021.123907.
Hasnat, A., and N. Ghafoori. 2021b. “Freeze–thaw resistance of nonproprietary ultrahigh-performance concrete.” J. Cold Reg. Eng. 35 (3): 04021008. https://doi.org/10.1061/(ASCE)CR.1943-5495.0000255.
Hasnat, A., and N. Ghafoori. 2021c. “Abrasion resistance of ultra-high-performance concrete for railway sleepers.” Urban Rail Transit, 7 (2): 101–116. https://doi.org/10.1007/s40864-021-00145-8.
Homayoonmehr, R., A. Rahai, and A. A. Ramezanianpour. 2022. “Predicting the chloride diffusion coefficient and surface electrical resistivity of concrete using statistical regression-based models and its application in chloride-induced corrosion service life prediction of RC structures.” Constr. Build. Mater. 357: 129351. https://doi.org/10.1016/j.conbuildmat.2022.129351.
Karim, R., M. Najimi, and B. Shafei. 2019. “Assessment of transport properties, volume stability, and frost resistance of non-proprietary ultra-high performance concrete.” Constr. Build. Mater. 227: 117031. https://doi.org/10.1016/j.conbuildmat.2019.117031.
Langan, B. W., K. Weng, and M. A. Ward. 2002. “Effect of silica fume and fly ash on heat of hydration of Portland cement.” Cem. Concr. Res. 32 (7): 1045–1051. https://doi.org/10.1016/S0008-8846(02)00742-1.
Le Hoang, A., and E. Fehling. 2017. “Influence of steel fiber content and aspect ratio on the uniaxial tensile and compressive behavior of ultra high performance concrete.” Constr. Build. Mater. 153: 790–806. https://doi.org/10.1016/j.conbuildmat.2017.07.130.
Li, Z., H. Zhang, and R. Wang. 2022. “Influence of steel fiber distribution on splitting damage and transport properties of ultra-high performance concrete.” Cem. Concr. Compos. 126: 104373. https://doi.org/10.1016/j.cemconcomp.2021.104373.
Liu, T., H. Wei, D. Zou, A. Zhou, and H. Jian. 2020. “Utilization of waste cathode ray tube funnel glass for ultra-high performance concrete.” J. Cleaner Prod. 249: 119333. https://doi.org/10.1016/j.jclepro.2019.119333.
Liu, Z., S. El-Tawil, W. Hansen, and F. Wang. 2018. “Effect of slag cement on the properties of ultra-high performance concrete.” Constr. Build. Mater. 190: 830–837. https://doi.org/10.1016/j.conbuildmat.2018.09.173.
Ma, R., L. Zhang, Y. Song, G. Lin, X. Qian, K. Qian, and S. Ruan. 2023. “Feasibility study on preparing economical and environmentally-friendly high-flowability ultra-high performance cementitious composites with original graded stone powder free recycled manufactured sands.” J. Cleaner Prod. 390: 136190. https://doi.org/10.1016/j.jclepro.2023.136190.
Mehta, P. K., and P. J. Monteiro. 2005. Concrete microstructure, properties and materials. 3rd ed. New York: McGraw Hill.
Mohammed, A. M., A. I. Al-Hadithi, and D. S. Asaad. 2020. “Investigating transport properties of low-binder ultrahigh-performance concretes: Binary and ternary blends of nanosilica, microsilica and cement.” Arabian J. Sci. Eng. 45 (10): 8369–8378. https://doi.org/10.1007/s13369-020-04737-7.
Mosavinejad, S. G., M. A. M. Langaroudi, J. Barandoust, and A. Ghanizadeh. 2020. “Electrical and microstructural analysis of UHPC containing short PVA fibers.” Constr. Build. Mater. 235: 117448. https://doi.org/10.1016/j.conbuildmat.2019.117448.
Muzenski, S., I. Flores-Vivian, and K. Sobolev. 2019. “Ultra-high strength cement-based composites designed with aluminum oxide nano-fibers.” Constr. Build. Mater. 220: 177–186. https://doi.org/10.1016/j.conbuildmat.2019.05.175.
Naber, C., S. Stegmeyer, D. Jansen, F. Goetz-Neunhoeffer, and J. Neubauer. 2019. “The PONKCS method applied for time resolved XRD quantification of supplementary cementitious material reactivity in hydrating mixtures with ordinary Portland cement.” Constr. Build. Mater. 214: 449–457. https://doi.org/10.1016/j.conbuildmat.2019.04.157.
Naik, T. R., R. N. Kraus, B. W. Ramme, and Y. M. Chun. 2005. “Deicing salt-scaling resistance: Laboratory and field evaluation of concrete containing up to 70% class C and class F fly ash.” J. ASTM Int. 2 (7): 1–12.
Onaizi, A. M., G. F. Huseien, N. H. A. S. Lim, M. Amran, and M. Samadi. 2021. “Effect of nanomaterials inclusion on sustainability of cement-based concretes: A comprehensive review.” Constr. Build. Mater. 306: 124850. https://doi.org/10.1016/j.conbuildmat.2021.124850.
Park, J. J., D. Y. Yoo, G. J. Park, and S. W. Kim. 2017. “Feasibility of reducing the fiber content in ultra-high-performance fiber-reinforced concrete under flexure.” Materials 10 (2): 118. https://doi.org/10.3390/ma10020118.
Piérard, J., B. Dooms, and N. Cauberg. 2013. “Durability evaluation of different types of UHPC.” In Proc., RILEM-fib-AFGC Int. Symp. on Ultra-High Performance Fiber-Reinforced Concrete, 1–3. Paris: International Union of Laboratories and Experts in Construction Materials, Systems and Structures.
Pyo, S., and H. K. Kim. 2017. “Fresh and hardened properties of ultra-high performance concrete incorporating coal bottom ash and slag powder.” Constr. Build. Mater. 131: 459–466. https://doi.org/10.1016/j.conbuildmat.2016.10.109.
Pyo, S., M. Tafesse, B. J. Kim, and H. K. Kim. 2018. “Effects of quartz-based mine tailings on characteristics and leaching behavior of ultra-high performance concrete.” Constr. Build. Mater. 166: 110–117. https://doi.org/10.1016/j.conbuildmat.2018.01.087.
Salahuddin, H., L. A. Qureshi, A. Nawaz, and S. S. Raza. 2020. “Effect of recycled fine aggregates on performance of reactive powder concrete.” Constr. Build. Mater. 243: 118223. https://doi.org/10.1016/j.conbuildmat.2020.118223.
Schmidt, M., and E. Fehling. 2005. “Ultra-high-performance concrete: Research, development and application in Europe.” ACI Spec. Publ. 228 (1): 51–78.
Shi, C. 2004. “Effect of mixing proportions of concrete on its electrical conductivity and the rapid chloride permeability test (ASTM C1202 or ASSHTO T277) results.” Cem. Concr. Res. 34 (3): 537–545. https://doi.org/10.1016/j.cemconres.2003.09.007.
Sobhani, J., and M. Najimi. 2013. “Electrochemical impedance behavior and transport properties of silica fume contained concrete.” Constr. Build. Mater. 47: 910–918. https://doi.org/10.1016/j.conbuildmat.2013.05.010.
Sritharan, S., G. Doiron, D. Bierwagen, B. Keierleber, and A. Abu-Hawash. 2018. “First application of UHPC bridge deck overlay in North America.” Transp. Res. Rec. 2672 (26): 40–47. https://doi.org/10.1177/0361198118755665.
Vaitkevičius, V., E. Šerelis, D. Vaičiukynienė, V. Raudonis, and Ž Rudžionis. 2016. “Advanced mechanical properties and frost damage resistance of ultra-high performance fibre reinforced concrete.” Constr. Build. Mater. 126: 26–31. https://doi.org/10.1016/j.conbuildmat.2016.09.012.
Vigneshwari, M., K. Arunachalam, and A. Angayarkanni. 2018. “Replacement of micro silica with thermally treated rice husk ash in reactive powder concrete.” J. Cleaner Prod. 188: 264–277. https://doi.org/10.1016/j.jclepro.2018.04.008.
Walker, R., and S. Pavía. 2011. “Physical properties and reactivity of pozzolans, and their influence on the properties of lime–pozzolan pastes.” Mater. Struct. 44 (6): 1139–1150. https://doi.org/10.1617/s11527-010-9689-2.
Wang, Y., M. Z. An, Z. R. Yu, S. Han, and W. Y. Ji. 2017. “Durability of reactive powder concrete under chloride-salt freeze–thaw cycling.” Mater. Struct. 50 (1): 18. https://doi.org/10.1617/s11527-016-0885-6.
Xi, J., J. Liu, K. Yang, S. Zhang, F. Han, J. Sha, and X. Zheng. 2022. “Role of silica fume on hydration and strength development of ultra-high performance concrete.” Constr. Build. Mater. 338: 127600. https://doi.org/10.1016/j.conbuildmat.2022.127600.
Xie, T., C. Fang, M. M. Ali, and P. Visintin. 2018. “Characterizations of autogenous and drying shrinkage of ultra-high performance concrete (UHPC): An experimental study.” Cem. Concr. Compos. 91: 156–173. https://doi.org/10.1016/j.cemconcomp.2018.05.009.
Yudenfreund, M., I. Odler, and S. Brunauer. 1972. “Hardened Portland cement pastes of low porosity I. Materials and experimental methods.” Cem. Concr. Res. 2 (3): 313–330. https://doi.org/10.1016/0008-8846(72)90073-7.
Zhang, P., Q. Li, Y. Chen, Y. Shi, and Y. F. Ling. 2019. “Durability of steel fiber-reinforced concrete containing SiO2 nano-particles.” Materials 12 (13): 2184. https://doi.org/10.3390/ma12132184.
Information & Authors
Information
Published In
Journal of Cold Regions Engineering
Volume 38 • Issue 2 • June 2024
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Dec 10, 2022
Accepted: Aug 11, 2023
Published online: Jan 24, 2024
Published in print: Jun 1, 2024
Discussion open until: Jun 24, 2024
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.