Postbuckling Behavior of FRP Bending-Active Arches Subjected to a Central Point Load
Publication: Journal of Composites for Construction
Volume 27, Issue 5
Abstract
A bending-active arch derives its curved shape from elastic bending of an initially straight strut. The recent revival of interest in this special structural form has been largely driven by the use of pultruded hollow-section fiber-reinforced polymer (FRP) profiles. Stability is a crucial concern for bending-active arches, because their unique forming method demands a sufficiently high flexibility (slenderness) to facilitate curvature development. However, previous theoretical results, especially those associated with postbuckling behavior, have not been verified with test results due to the lack of loading tests. To fill this gap, this study conducted central point loading tests on FRP bending-active arches, which successfully captured the full-range postbuckling response. The test data fulfilled the intended goal of verifying a nonlinear load–deflection (equilibrium path) analysis. In this paper, the results of the loading tests are first presented. The differential equations governing the equilibrium path are next formulated and then solved as a boundary value problem (BVP) using a numerical BVP solver. Finally, the results of parametric studies performed using the verified BVP solver are presented. The results show that the effect of gravity on the mechanical behavior of FRP bending-active arches is negligible, whereas the forming-induced prestresses have a negative effect on the buckling load. In the range of practical arch shapes, the loss in buckling load due to this effect is approximately 10%.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors are grateful for the financial support provided by the Zhejiang Provincial Natural Science Foundation (Project No.: LY15E080007).
Notation
The following symbols are used in this paper:
- b
- width of an FRP strip;
- D
- outer diameter of an FRP pipe;
- Ef
- flexural modulus;
- Et
- tensile modulus;
- HA
- horizontal reaction force at Point A;
- Hcr
- Euler’s buckling load;
- h
- rise of an arch;
- I
- area moment of inertia;
- L
- length of an arch;
- l
- span of an arch;
- M
- moment;
- MA
- reaction moment at Point A;
- Mnom
- normalized moment;
- Q
- vertical point load at the arch crown;
- Qnom
- normalized vertical point load at the arch crown;
- Qp
- arch buckling load;
- normalized buckling load;
- Qv
- valley load;
- s
- arc length from Point A;
- s0
- varying arc length from Point A in the range of 0 and s;
- t
- thickness of an FRP strip;
- tw
- wall thickness of FRP pipe;
- VA
- vertical reaction force at Point A;
- w
- gravity per unit length;
- x
- abscissa value;
- x0
- abscissa value corresponding to s0;
- y
- ordinate value;
- ΔL
- displacement of an arch end;
- Δmid
- midspan deflection;
- normalized midspan deflection;
- axial strain capacity;
- η
- buckling load ratio;
- θ
- rotation;
- θ0
- initial tangential angle of an companion arch segment;
- θ1
- rotation of an companion arch segment;
- θA
- rotation at Point A;
- κ
- curvature;
- λ
- slenderness ratio;
- ξ
- percentage loss of buckling load; and
- ρ
- density.
References
Armanini, C., F. Dal Corso, D. Misseroni, and D. Bigoni. 2017. “From the elastica compass to the elastica catapult: An essay on the mechanics of soft robot arm.” Proc. R. Soc. A 473 (2198): 20160870. https://doi.org/10.1098/rspa.2016.0870.
ASTM. 2017. Standard test method for tensile properties of polymer matrix composite materials. ASTM D3039/D3039M-17. West Conshohocken, PA: ASTM.
ASTM. 2021. Standard test method for flexural properties of polymer matrix composite materials. ASTM D7264/D7264M-21. West Conshohocken, PA: ASTM.
Austin, W. J. 1971. “In-plane bending and buckling of arches.” J. Struct. Div. 97 (5): 1575–1592.
Bai, Y., and T. Keller. 2009. “Shear failure of pultruded fiber-reinforced polymer composites under axial compression.” J. Compos. Constr. 13 (3): 234–242.
Bai, Y., T. Vallée, and T. Keller. 2009. “Delamination of pultruded glass fiber-reinforced polymer composites subjected to axial compression.” Compos. Struct. 91 (1): 66–73.
Baverel, O., J.-F. Caron, F. Tayeb, and L. Du Peloux. 2012. “Gridshells in composite materials: construction of a 300 m2 forum for the solidays’ festival in Paris.” Struct. Eng. Int. 22 (3): 408–414. https://doi.org/10.2749/101686612X13363869853572.
Bessini, J., C. Lázaro, J. Casanova, and S. Monleón. 2019. “Efficiency-based design of bending-active tied arches.” Eng. Struct. 200: 109681. https://doi.org/10.1016/j.engstruct.2019.109681.
Bessini, J., S. Monleón, J. Casanova, and C. Lázaro. 2021. “Shape generation of bending-active braced arches based on elastica curves.” J. Int. Assoc. Shell Spatial Struct. 62 (2): 138–152.
Caron, J.-F., S. Julich, and O. Baverel. 2009. “Selfstressed bowstring footbridge in FRP.” Compos. Struct. 89 (3): 489–496. https://doi.org/10.1016/j.compstruct.2008.11.009.
Chen, J.-S., and H.-W. Tsao. 2013. “Static snapping load of a hinged extensible elastica.” Appl. Math. Modell. 37 (18–19): 8401–8408. https://doi.org/10.1016/j.apm.2013.03.040.
Chilton, J., and G. Tang. 2016. Timber gridshells: Architecture, structure and craft. London: Routledge.
Douthe, C., J.-F. Caron, and O. Baverel. 2010. “Gridshell structures in glass fibre reinforced polymers.” Constr. Build. Mater. 24 (9): 1580–1589. https://doi.org/10.1016/j.conbuildmat.2010.02.037.
Du Peloux, L., F. Tayeb, O. Baverel, and J.-F. Caron. 2016. “Construction of a large composite gridshell structure: A lightweight structure made with pultruded glass fibre reinforced polymer tubes.” Struct. Eng. Int. 26 (2): 160–167. https://doi.org/10.2749/101686616X14555428758885.
Euler, L. 1744. Methodus inveniendi lineas curvas maximi minimive proprietate gaudentes, sive solutio problematis isoperimetrici latissimo sensu accepti. Genevæ: Apud Marcum-Michaelem Bousquet et socios.
Garikipati, K., S. Göktepe, and C. Miehe. 2008. “Elastica-based strain energy functions for soft biological tissue.” J. Mech. Phys. Solids 56 (4): 1693–1713. https://doi.org/10.1016/j.jmps.2007.07.005.
Glassmaker, N., and C. Hui. 2004. “Elastica solution for a nanotube formed by self-adhesion of a folded thin film.” J. Appl. Phys. 96 (6): 3429–3434. https://doi.org/10.1063/1.1779974.
Habibi, T., L. Rhode-Barbarigos, and T. Keller. 2022. “Fiber-polymer composites for permanent large-scale bending-active elastica beams.” Compos. Struct. 294: 115809.
Happold, E., and W. Liddell. 1975. “Timber lattice roof for the Mannheim Bundesgartenschau.” Struct. Eng. 53: 99–135.
Harris, R., S. Haskins, and J. Roynon. 2008. “The Savill Garden gridshell: Design and construction.” Struct. Eng. 86 (17): 27–34.
Harris, R., J. Romer, O. Kelly, and S. Johnson. 2003. “Design and construction of the Downland Gridshell.” Build. Res. Inf. 31 (6): 427–454. https://doi.org/10.1080/0961321032000088007.
Hu, N., and R. Burgueño. 2015. “Buckling-induced smart applications: Recent advances and trends.” Smart Mater. Struct. 24 (6): 063001.
Jeon, J.-H., T.-H. Cheng, and I.-K. Oh. 2010. “Snap-through dynamics of buckled IPMC actuator.” Sens. Actuators, A 158 (2): 300–305.
Kierzenka, J., and L. F. Shampine. 2001. “A BVP solver based on residual control and the Maltab PSE.” ACM Trans. Math. Software 27 (3): 299–316. https://doi.org/10.1145/502800.502801.
Lázaro, C., S. Monleón, and J. Bessini. 2017. “Tangent stiffness in point-loaded elastica arches.” In Proc., IASS Annual Symp., 1–8. Hamburg, Germany: International Association for Shell and Spatial Structures (IASS).
Lázaro, C., S. Monleón, and J. Casanova. 2015. “Can the force density method be extended for active bending structures?” In Proc., IASS Annual Symp., 1–12. Amsterdam, The Netherlands: International Association for Shell and Spatial Structures (IASS).
Lee, T.-U., and Y. M. Xie. 2021. “From ruled surfaces to elastica-ruled surfaces: New possibilities for creating architectural forms.” J. Int. Assoc. Shell Spatial Struct. 62 (4): 271–281. https://doi.org/10.20898/j.iass.2021.014.
Lee, T.-U., Z. You, and J. M. Gattas. 2018. “Elastica surface generation of curved-crease origami.” Int. J. Solids Struct. 136: 13–27. https://doi.org/10.1016/j.ijsolstr.2017.11.029.
Liddell, I. 2015. “Frei Otto and the development of gridshells.” Case Stud. Struct. Eng. 4: 39–49. https://doi.org/10.1016/j.csse.2015.08.001.
Lienhard, J. 2014. “Bending-active structures: form-finding strategies using elastic deformation in static and kinetic systems and the structural potentials therein.” Ph.D. thesis, Institute of Building Structures and Structural Design, Univ. of Stuttgart.
Lienhard, J., H. Alpermann, C. Gengnagel, and J. Knippers. 2013. “Active bending, a review on structures where bending is used as a self-formation process.” Int. J. Space Struct. 28 (3–4): 187–196. https://doi.org/10.1260/0266-3511.28.3-4.187.
Love, A. E. H. 1892. A treatise on the mathematical theory of elasticity. Cambridge: Cambridge University Press.
Mesnil, R., J. Ochsendorf, and C. Douthe. 2015. “Stability of pseudo-funicular elastic grid shells.” Int. J. Space Struct. 30 (1): 27–36.
Mujika, F., N. Carbajal, A. Arrese, and I. Mondragon. 2006. “Determination of tensile and compressive moduli by flexural tests.” Polym. Test. 25 (6): 766–771. https://doi.org/10.1016/j.polymertesting.2006.05.003.
Naicu, D.-I. 2012. “Geometry and performance of timber gridshells.” Ph.D. thesis, Department of Architecture and Civil Engineering, Univ. of Bath.
Nallathambi, A. K., C. L. Rao, and S. M. Srinivasan. 2010. “Large deflection of constant curvature cantilever beam under follower load.” Int. J. Mech. Sci. 52 (3): 440–445. https://doi.org/10.1016/j.ijmecsci.2009.11.004.
Pi, Y.-L., M. Bradford, and B. Uy. 2002. “In-plane stability of arches.” Int. J. Solids Struct. 39 (1): 105–125.
Pippard, A. 1990. “The elastic arch and its modes of instability.” Eur. J. Phys. 11 (6): 359–365.
Sonntag, D., S. Bechert, and J. Knippers. 2017. “Biomimetic timber shells made of bending-active segments.” Int. J. Space Struct. 32 (3–4): 149–159.
Toussaint, M. 2007. “A design tool for timber gridshells: the development of a grid generation tool.” Master’s thesis, Faculty of Civil Engineering and Geosciences, Delft Univ. of Technology.
Information & Authors
Information
Published In
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Aug 18, 2022
Accepted: Apr 13, 2023
Published online: Jun 20, 2023
Published in print: Oct 1, 2023
Discussion open until: Nov 20, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.