Research on Rock Support Technology of Railway Tunnels Based on Geomechanical Model Tests
Publication: International Journal of Geomechanics
Volume 24, Issue 8
Abstract
The technology of combining a negative Poisson's ratio (NPR) anchor cable with a double-layer truss support technology (N-DTST) is a new support technology for deeply buried tunnels. To evaluate the stability of the surrounding rock support after the application of this new support technology in the Sichuan–Tibet Railway tunnels, geomechanical model tests were conducted for the first time. A model test loading system with intelligent numerical control and automated analysis was developed to reveal the changing patterns of displacement and stress in the surrounding rock of tunnels. The test results revealed the following: (1) After the burial depth exceeds 800 m, the tunnel undergoes large deformations with displacements greater than 37.5 mm, and the traditional anchor cable support fails; (2) In the burial depth range of 800–2,000 m, the new support technology can control the surrounding rock deformation, and the surrounding rock displacement is less than 10 mm; (3) After the tunnel excavation, the radial stress decreases and the tangential stress concentrates. When the burial depth is greater than 800 m, the radial stress compensation provided by the anchor cable no longer meets the stability of the tunnel surrounding rock, and the new support technology can provide high stress to support the deeply buried tunnel; (4) After the burial depth exceeds 2,000 m, butterfly-shaped damage occurs on the tunnel surface, the truss structure inside the tunnel is damaged, and the support structure fails, so it is recommended to carry out reinforcement support at the arch shoulder. The research results verify the effectiveness of the new support technology and provide an important reference for the support of the surrounding rock in deeply buried tunnels.
Practical Applications
Common Poisson's ratio anchors/ropes or shotcrete are widely used in tunnels as the core support structure. They often fail to meet the requirements of fractured rock, expansive rock, and high-ground-stress soft rock tunnels because they cannot adapt to the large deformation characteristics of the catastrophic rock mass. Based on this, this paper proposed a new support technology: an anchor rod/rope with a negative Poisson's ratio material combined with a double-layer three-dimensional truss for joint support of the tunnel. To verify the feasibility of this technology, the research and development team developed a new design for the structure. To verify the feasibility of this technology, a large-scale geomechanical model test system was developed, and a comparative model test was conducted using this test system in combination with the ground stress environment of the Sichuan–Tibet Railway to verify the effectiveness of the new support technology proposed in this paper, which provides a reference for the world's deep buried tunnel support technology.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and codes generated or used during the study appear in the published article.
Acknowledgments
This work was supported by the National Natural Science Foundation of China (Grant No. 41941018).
References
Cantieni, L., and G. Anagnostou. 2009. “The interaction between yielding supports and squeezing ground.” Tunnelling Underground Space Technol. 24: 309–322. https://doi.org/10.1016/j.tust.2008.10.001.
Chen, A., J. Gu, J. Shen, Z. Ming, L. Gu, and Z. Lu. 2004. “Application study on the geomechanical model experiment techniques.” Chin. J. Rock Mech. Eng. 23: 3785–3789.
Chen, F. 2009. In Research on failure evolution and control mechanism of surrounding rock of deep roadways and its application, 18–20. Xuzhou, China: China University of Mining and Technology.
Chen, X., Q. Zhang, D. Liu, N. Zhang, and S. Li. 2011. “A 3-D geomechanics model test study of the anchoring character for deep tunnel excavations.” China Civil Eng. J. 44: 107–113.
He, M., and Z. Guo. 2014. “Mechanical property and engineering application of anchor bolt with constant resistance and large deformation.” Chin. J. Rock Mech. Eng. 33: 1297–1308.
He, M., C. Li, W. Gong, J. Wang, and Z. Tao. 2016. “Support principles of NPR bolts/cables and control techniques of large deformation.” Chin. J. Rock Mech. Eng. 35: 1513–1529.
He, M., Q. Sui, M. Li, Z. Wang, and Z. Tao. 2022. “Compensation excavation method control for large deformation disaster of mountain soft rock tunnel.” Int. J. Min. Sci. Technol. 32: 951–963. https://doi.org/10.1016/j.ijmst.2022.08.004.
He, M., H. Xie, S. Peng, and Y. Jiang. 2005. “Study on rock mechanics in deep mining engineering.” Chin. J. Rock Mech. Eng. 24: 2803–2813.
Huo, J., C. Lin, and Z. Liu. 2021. “Experimental study on high performance fiber shotcrete ratio for tunnel support.” Railway Stand. Des. 65: 65–73.
Kovari, K., and J. Staus. 1996. “Basic considerations on tunnelling in squeezing ground.” Rock Mech. Rock Eng. 29: 203–210. https://doi.org/10.1007/BF01042533.
Lan, H., et al. 2021. “Risk analysis of major engineering geological hazards for Sichuan–Tibet railway in the phase of feasibility study.” J. Eng. Geol. 29: 326–341.
Lei, S., and W. Zhao. 2020. “Study on mechanism of circumferential yielding support for soft rock tunnel with large deformation.” Rock Soil Mech. 41: 1039–1047.
Li, G., Y. Hu, S.-M. Tian, M. Weibin, and H.-L. Huang. 2021. “Analysis of deformation control mechanism of prestressed anchor on jointed soft rock in large cross-section tunnel.” Bull. Eng. Geol. Environ. 80: 9089–9103. https://doi.org/10.1007/s10064-021-02470-5.
Li, L., S. Li, Y. Zhao, S. Li, H. Wang, Q. Liu, Y. Zhao, and X. Yuan. 2012. “3D geomechanical model for progressive failure progress of weak broken surrounding rock in super large section tunnel.” Chin. J. Rock Mech. Eng. 31: 550–560.
Li, S., D. Wang, Q. Wang, F. Wang, P. Peng, W. Li, B. Jiang, and H. Wang. 2013. “Development and application of large-scale geomechanical model test system for deep thick top coal roadway.” J. China Coal Soc. 38: 1522–1530.
Li, Y. 2011. “Construction control technology of high geostress soft rock and large deformation in Mao Yu mountain tunnel.” Mod. Tunnelling Technol. 48: 59–67.
Li, Z., D. Lu, S. Zhong, J. Xi, and J. Sun. 2003. “Development and application of new technology for 3D geo-mechanics model test of large underground houses.” Chin. J. Rock Mech. Eng. 22: 1430–1436.
Li, Z., Q. Xu, G. Luo, and A. Wang. 2002. “Three-dimensional geomechanical model test of large underground hydroelectric power plant cavern group.” Shuili Xuebao 4: 31–36.
Liu, G. 2011. “Research on support measures for soft rock with large deformation section in Muzhailing tunnel.” Mod. Tunnelling Technol. 48: 135–141+147.
Liu, Y., C. Xia, F. Wu, C. Xu, and Y. Deng. 2020. “A combined support technology of long and short bolts of soft rock tunnels under high ground stresses.” Chin. J. Rock Mech. Eng. 39: 105–114.
Ma, F., Z. Li, and G. Luo. 2004. “NIOS model material and its use in geo-mechanical similarity model test.” J. Hydroelectric Eng. 23: 48–51.
Oparin, V. N., V. F. Yushkin, G. N. Polyankin, A. N. Grishin, A. O. Kuznetsov, and D. E. Rublev. 2016. “Geomechanical monitoring of temporal lining in railway tunneling in complex geological conditions.” J. Min. Sci. 51: 839–859. https://doi.org/10.1134/S1062739115040226.
Tao, Z., S. Luo, M. Li, S. Ren, and M. He. 2020. “Optimization of large deformation control parameters of layered slate tunnels based on numerical simulation and field test.” Chin. J. Rock Mech. Eng. 39: 491–506.
Tao, Z., H. Zhang, Y. Peng, S. Zhao, and M. He. 2017. “Frame structure and engineering applications of multi-source system cloud service platform for landslide monitoring.” Chin. J. Rock Mech. Eng. 36: 1649–1658.
Tian, H., W. Chen, X. Tan, H. Wang, and T. Tian. 2011. “Study of reasonable support scheme for soft rock tunnel in high geostress zone.” Chin. J. Rock Mech. Eng. 30: 2285–2292.
Tian, S., W. Wang, G. Li, W. Tao, and S. Shi. 2021. “Design concept and main principles of tunnel on Sichuan–Tibet railway.” Tunnel Constr. 41: 519.
Wang, C., G. Gao, S. Yang, R. Yao, and L. Huang. 2019. “Analysis and prediction of stress fields of Sichuan–Tibet railway area based on contemporary tectonic stress field zoning in western China.” Chin. J. Rock Mech. Eng. 38: 2242–2253.
Wang, H., S. Li, X. Zheng, and W. Zhu. 2009. “Research progress of geomechanical model test with new technology and its engineering application.” Chin. J. Rock Mech. Eng. 28: 2765–2771.
Wang, J., L. Chen, R. Su, and X. Zhao. 2018a. “The Beishan underground research laboratory for geological disposal of high-level radioactive waste in China: Planning, site selection, site characterization and in situ tests.” J. Rock Mech. Geotech. Eng. 10: 411–435. https://doi.org/10.1016/j.jrmge.2018.03.002.
Wang, K.-Z., X.-L. Liu, Z.-H. Jin, L. Dong, and K. Yang. 2020. “Experimental study on deformation law of soil layer induced by undercut between existing twin tunnels based on 3D geomechanical model.” IOP Conf. Ser.: Earth Environ. Sci. 570: 052061. https://doi.org/10.1088/1755-1315/570/5/052061.
Wang, S. G., Y. R. Liu, Z. F. Tao, Y. Zhang, D. N. Zhong, Z. S. Wu, C. Lin, and Q. Yang. 2018b. “Geomechanical model test for failure and stability analysis of high arch dam based on acoustic emission technique.” Int. J. Rock Mech. Min. Sci. 112: 95–107. https://doi.org/10.1016/j.ijrmms.2018.10.018.
Wang, Y., W. Cheng, and J. Liu. 2022. “Forming process and mechanisms of geo-hazards in luding section of the Sichuan–Tibet railway.” Earth Sci. J. China Univ. Geosci. 47: 950–958. https://doi.org/10.3799/dqkx.2021.179.
Wang, Y., A. Wu, C. Zhang, and B. Teng. 2006. “Experimental research on similarity model for ore-pillar recovery under complex conditions.” Metal Mine 12: 10–12.
Xia, C., C. Xu, and S. Du. 2021. “Interaction between viscoelastic-plastic surrounding rock and support structure in deep tunnels considering stress path.” Chin. J. Rock Mech. Eng. 40: 1789–1802.
Yuan, P., and Y. Xu. 2019. “Analyses on deformation and fracture evolution of zonal disintegration during axial overloading in 3D geomechanical model tests.” J. Vibroeng. 21: 1163–1174. https://doi.org/10.21595/jve.2019.20619.
Zhang, Q., S. Li, C. You, and X. Guo. 2007. “Development and application of new type combination 3D geomechanical model test rack apparatus.” Chin. J. Rock Mech. Eng. 26: 143–148. https://doi.org/10.3901/JME.2007.03.143.
Zhang, Q., C. Liu, K. Duan, Z. Zhang, and W. Xiang. 2019. “True three-dimensional geomechanical model tests for stability analysis of surrounding rock during the excavation of a deep underground laboratory.” Rock Mech. Rock Eng. 53: 517–537. https://doi.org/10.1007/s00603-019-01927-0.
Zhang, Q. B., L. He, and W. S. Zhu. 2016. “Displacement measurement techniques and numerical verification in 3D geomechanical model tests of an underground cavern group.” Tunnelling Underground Space Technol. 56: 54–64. https://doi.org/10.1016/j.tust.2016.01.029.
Zhang, Z. 1997. “Remediation of large deformation of support during the construction of Jiazhuyi tunnel.” World Tunnels 1: 7–16.
Zhao, Y., S. Li, Y. Zhao, and L. Li. 2012. “Model test study of surrounding rock load releasing during super-large section tunnel excavation.” Chin. J. Rock Mech. Eng. 31: 3821–3830.
Zhu, W., Y. Li, L. Zhang, X. Xin, L. Sun, Q. Ma, W. Chen, J. Li, and L. Zhang. 2008. “Geomechanical model test on stability of cavern group under high geostress.” Chin. J. Rock Mech. Eng. 27: 1308–1314.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 24 • Issue 8 • August 2024
Copyright
© 2024 American Society of Civil Engineers.
History
Received: Jun 24, 2023
Accepted: Feb 1, 2024
Published online: May 20, 2024
Published in print: Aug 1, 2024
Discussion open until: Oct 20, 2024
ASCE Technical Topics:
- Anchors
- Cables
- Continuum mechanics
- Displacement (mechanics)
- Engineering fundamentals
- Engineering mechanics
- Equipment and machinery
- Geology
- Geotechnical engineering
- Infrastructure
- Rail transportation
- Rocks
- Solid mechanics
- Structural engineering
- Structural mechanics
- Structures (by type)
- Transportation engineering
- Tunnels
- Underground structures
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.