Technical Papers
Jul 6, 2023

Cooling Methods under High-Temperature Effects on Creep Properties and Nonlinear Creep Damage Model of Quartz Sandstone

Publication: International Journal of Geomechanics
Volume 23, Issue 9

Abstract

In order to compare and study the creep mechanical behavior of quartz sandstone under the action of different cooling methods in high temperature, firstly, triaxial creep tests of quartz sandstone after natural cooling and water cooling are carried out, and creep curves under two conditions and different temperatures are obtained, respectively. Meanwhile, the mesodamage characteristics of quartz sandstone under the action of different cooling methods are analyzed. Based on experimental data and statistical damage theory, an improved Burgers creep damage model is proposed, and the model parameters are subjected to sensitivity analysis. The test results show that the creep process of quartz sandstone under different cooling methods has three-stage characteristics, and the creep rate increases gradually with temperature, whereas the long-term strength decreases gradually. Under the same temperature, the creep rate of quartz sandstone under water cooling is higher than that under natural cooling, whereas the long-term strength is lower than that of natural cooling. The mesoscopic test also shows that the damage degree of water cooling to the rock is higher than that of natural cooling. Finally, by comparing with the experimental data, it is found that the proposed improved Burgers creep damage model can effectively reflect the influence of different cooling methods on the creep properties of quartz sandstone. The results of this paper can provide important scientific significance for the damage assessment, repair, and reinforcement of tunnel surrounding rock and other structures under high temperatures.

Get full access to this article

View all available purchase options and get full access to this article.

Acknowledgments

This work was supported by the National Natural Science Foundation of China (Nos. 52078093 and 51678101) and the Liao Ning Revitalization Talents Program (No. XLYC1905015). The authors are thankful for this institutional support and to the reviewers for their valuable comments to improve this manuscript.

References

Akker, I. V., A. Berger, H. Zwingmann, A. Todd, C. E. Schrank, M. W. M. Jones, C. M. Kewish, T. C. Schmid, and M. Herwegh. 2021. “Structural and chemical resetting processes in white mica and their effect on K–Ar data during low temperature metamorphism.” Techonophysics 800: 228708. https://doi.org/10.1016/j.tecto.2020.228708.
Bhat, D. R., J. V. Kozubal, and M. Tankiewicz. 2021. “Extended residual-state creep test and its application for landslide stability assessment.” Materials 14 (8): 1968. https://doi.org/10.3390/ma14081968.
Cheng, H., Y. C. Zhang, and X. P. Zhou. 2021. “Nonlinear creep model for rocks considering damage evolution based on the modified Nishihara model.” Int. J. Geomech. 21 (8): 04021137. https://doi.org/10.1061/(ASCE)GM.1943-5622.0002071.
Daou, I., G. L. Lecomte-Nana, N. Tessier-Doyen, C. Peyratout, M. F. Gonon, and R. Guinebretiere. 2020. “Probing the dehydroxylation of kaolinite and halloysite by in situ high temperature X-ray diffraction.” Minerals 10 (5): 480. https://doi.org/10.3390/min10050480.
Deng, L. C., X. Z. Li, Y. C. Wang, Y. Wu, Z. Huang, and C. L. Jiang. 2022. “Effect of temperature on macroscopic and microscopic properties of sandstone from Qidong coal mine.” Rock Mech. Rock Eng. 55 (1): 71–90. https://doi.org/10.1007/s00603-021-02679-6.
Fan, L. F., H. Li, and Y. Xi. 2022. “Evaluation of the effects of three different cooling methods on the dynamic mechanical properties of thermal-treated sandstone.” Bull. Eng. Geol. Environ. 81 (4): 154. https://doi.org/10.1007/s10064-022-02630-1.
Feng, W. L., C. S. Qiao, and S. J. Niu. 2020. “Study on sandstone creep properties of Jushan Mine affected by degree of damage and confining pressure.” Bull. Eng. Geol. Environ. 79 (2): 869–888. https://doi.org/10.1007/s10064-019-01682-0.
Gao, Y. F., and D. S. Yin. 2021. “A full-stage creep model for rocks based on the variable-order fractional calculus.” Appl. Math. Modell. 95: 435–446. https://doi.org/10.1016/j.apm.2021.02.020.
Gautam, P. K., A. K. Verma, P. Sharma, and T. N. Singh. 2018. “Evolution of thermal damage threshold of Jalore granite.” Rock Mech. Rock Eng. 51 (9): 2949–2956. https://doi.org/10.1007/s00603-018-1493-2.
Gutierrez-Ch, J. G., S. Senent, P. Zeng, and R. Jimenez. 2022. “DEM simulation of rock creep in tunnels using rate process theory.” Comput. Geotech. 142: 104559. https://doi.org/10.1016/j.compgeo.2021.104559.
Hsu, W. S., Y. H. Huang, T. S. Shen, C. Y. Cheng, and T. Y. Chen. 2017. “Analysis of the Hsuehshan tunnel fire in Taiwan.” Tunnelling Underground Space Technol. 69: 108–115. https://doi.org/10.1016/j.tust.2017.06.011.
Huang, Z., W. Zeng, Q. X. Gu, Y. Wu, W. Zhong, and K. Zhao. 2021. “Investigations of variations in physical and mechanical properties of granite, sandstone, and marble after temperature and acid solution treatments.” Constr. Build. Mater. 307: 124943. https://doi.org/10.1016/j.conbuildmat.2021.124943.
Jin, A. B., S. L. Wang, Y. D. Wei, H. Sun, and L. C. Wei. 2020. “Effect of different cooling conditions on physical and mechanical properties of high-temperature sandstone.” [In Chinese.] Rock Soil. Mech. 41 (11): 1–10. https://doi.org/10.16285/j.rsm.2020.0232.
Kang, F. C., T. R. Jia, Y. C. Li, J. H. Deng, C. A. Tang, and X. Huang. 2021. “Experimental study on the physical and mechanical variations of hot granite under different cooling treatments.” Renewable Energy 179: 1316–1328. https://doi.org/10.1016/j.renene.2021.07.132.
Lee, A. L., H. Stunitz, M. Soret, and M. A. Battisti. 2022. “Dissolution precipitation creep as a process for the strain localisation in mafic rocks.” J. Struct. Geol. 155: 104505. https://doi.org/10.1016/j.jsg.2021.104505.
Li, D. Y., S. H. Du, C. S. Zhang, D. W. Mao, and B. Ruan. 2021. “Time-dependent deformation behavior of completely weathered granite subjected to wetting immersion.” Rock Mech. Rock Eng. 54 (12): 6373–6391. https://doi.org/10.1007/s00603-021-02615-8.
Li, Z. H., L. N. Y. Wong, and C. I. The. 2017. “Low cost colorimetry for assessment of fire damage in rock.” Eng. Geol. 228: 50–60. https://doi.org/10.1016/j.enggeo.2017.07.006.
Liu, Y. R., W. Q. Wa, Z. He, S. Lyv, and Q. Yang. 2020. “Nonlinear creep damage model considering effect of pore pressure and analysis of long-term stability of rock structure.” Int. J. Damage Mech. 29 (S1): 144–165. https://doi.org/10.1177/1056789519871684.
Lusk, A. D. J., J. P. Plat, and J. A. Platt. 2021. “Natural and experimental constraints on a flow law for dislocation-dominated creep in wet quartz.” J. Geophys. Res. Solid Earth 126 (5): e2020JB021302. https://doi.org/10.1029/2020JB021302.
Lyu, C., J. F. Liu, Y. Ren, C. Liang, and Y. L. Liao. 2021. “Study on very long-term creep tests and nonlinear creep-damage constitutive model of salt rock.” Int. J. Rock Mech. Min. Sci. 146: 104873. https://doi.org/10.1016/j.ijrmms.2021.104873.
Marini, P., and R. Bellopede. 2013. “The use of tunnel muck as industrial raw material: Two case-studies.” Rock Mech. Rock Eng. 46 (2): 397–404. https://doi.org/10.1007/s00603-012-0266-6.
Martin, S., and S. Michael. 1995. “Measurements of the severity of fires involving private motor vehicles.” Fire Mater. 19: 143–151. https://doi.org/10.1002/fam.810190307.
Martinola, G., M. F. Bauml, and A. Walliser. 2007. “Numerical modeling of the long-term behavior of passive fire protection mortars applied on concrete tunnels.” J. Mater. Civ. Eng. 19 (6): 484–491. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:6(484).
Ozeki, G., A. T. Yokobori, and D. Kobayashi. 2022. “Effect of overload on creep deformation, crack initiation and growth behaviors of a C(T) specimen for 12Cr steel.” Eng. Fract. Mech. 264: 108313. https://doi.org/10.1016/j.engfracmech.2022.108313.
Sabitova, A., V. M. Yarushina, S. Stanchits, V. Stukachev, L. Khakimova, and A. Myasnikov. 2021. “Experimental compaction and dilation of porous rocks during triaxial creep and stress relaxation.” Rock Mech. Rock Eng. 54 (11): 5781–5805. https://doi.org/10.1007/s00603-021-02562-4.
Sha, S., G. Rong, Z. H. Chen, B. W. Li, and Z. Y. Zhang. 2020. “Experimental evaluation of physical and mechanical properties of geothermal reservoir rock after different cooling treatments.” Rock Mech. Rock Eng. 53 (11): 4967–4991. https://doi.org/10.1007/s00603-020-02200-5.
Sirdesai, N. N., B. Mahanta, P. G. Ranjith, and T. N. Singh. 2019. “Effects of thermal treatment on physico-morphological properties of Indian fine-grained sandstone.” Bull. Eng. Geol. Environ. 78 (2): 883–897. https://doi.org/10.1007/s10064-017-1149-6.
Sisodiya, M., and Y. D. Zhang. 2022. “A time-dependent directional damage theory for brittle rocks considering the kinetics of microcrack growth.” Rock Mech. Rock Eng. 55: 2693–2710. https://doi.org/10.1007/s00603-021-02577-x.
Tsang, H. L., N. K. Fong, and W. K. Chow. 2020. “A simulation study on fire safety aspects of rock cavern accommodating high occupant load.” Tunnelling Underground Space Technol. 103: 103430. https://doi.org/10.1016/j.tust.2020.103430.
Wallis, D., M. Sep, and L. N. Hansen. 2022. “Transient creep in subduction zones by long-range dislocation interactions in olivine.” J. Geophys. Res. Solid Earth 127 (1): e2021JB022618. https://doi.org/10.1029/2021JB022618.
Wang, F., T. Fruhwirt, H. Konietzky, and Q. Y. Zhu. 2019. “Thermo-mechanical behaviour of granite during high-speed heating.” Eng. Geol. 260: 105258. https://doi.org/10.1016/j.enggeo.2019.105258.
Wang, J. B., Q. Zhang, Z. P. Song, and Y. W. Zhang. 2020. “Creep properties and damage constitutive model of salt rock under uniaxial compression.” Int. J. Damage Mech. 29 (6): 902–922. https://doi.org/10.1177/1056789519891768.
Wasantha, P. L. P., M. Guerrieri, and T. Xu. 2021. “Effects of tunnel fires on the mechanical behaviour of rocks in the vicinity—A review.” Tunnelling Underground Space Technol. 108: 103667. https://doi.org/10.1016/j.tust.2020.103667.
Wu, L. Z., B. Li, R. Q. Huang, and P. Sun. 2017. “Experimental study and modeling of shear rheology in sandstone with non-persistent joints.” Eng. Geol. 222: 201–211. https://doi.org/10.1016/j.enggeo.2017.04.003.
Wu, X. G., Z. W. Huang, X. W. Dai, H. Y. Song, and S. K. Zhang. 2020. “Thermo-coupled FSI analysis of LN2 jet impinging on hot dry rock.” Appl. Therm. Eng. 165: 114621. https://doi.org/10.1016/j.applthermaleng.2019.114621.
Yang, S. Q., and B. Hu. 2020. “Creep and permeability evolution behavior of red sandstone containing a single fissure under a confining pressure of 30 MPa.” Sci. Rep. 10 (1): 1900. https://doi.org/10.1038/s41598-020-58595-2.
Yang, S. Q., P. G. Ranjith, H. W. Jing, W. L. Tian, and Y. Ju. 2018. “An experimental investigation on thermal damage and failure mechanical behavior of granite after exposure to different high temperature treatments.” Geothermics 65: 180–197. https://doi.org/10.1016/j.geothermics.2016.09.008.
Zhang, L., H. W. Zhou, X. Y. Wang, L. Wang, T. Su, Q. Wei, and T. F. Deng. 2021. “A triaxial creep model for deep coal considering temperature effect based on fractional derivative.” Acta Geotech. 17 (5): 1739–1751. https://doi.org/10.1007/s11440-021-01302-w.
Zhao, X., H. W. Zhang, H. P. Lai, H. P. Yang, X. H. Yang, X. Y. Wang, and X. L. Zhao. 2020. “Temperature field characteristics and influencing factors on frost depth of a highway tunnel in a cold region.” Cold. Reg. Sci. Technol. 179: 103141. https://doi.org/10.1016/j.coldregions.2020.103141.
Zhao, Y. Y., Q. Sun, S. F. Wang, L. W. Zhang, and Z. Q. Jiang. 2022. “Pore characteristics and permeability changes of high-temperature limestone after rapid cooling by dry ice.” Heat Mass Transfer 58 (1): 1339–1352. https://doi.org/10.1007/s00231-021-03171-1.

Information & Authors

Information

Published In

Go to International Journal of Geomechanics
International Journal of Geomechanics
Volume 23Issue 9September 2023

History

Received: Jun 21, 2022
Accepted: Mar 25, 2023
Published online: Jul 6, 2023
Published in print: Sep 1, 2023
Discussion open until: Dec 6, 2023

Permissions

Request permissions for this article.

Authors

Affiliations

Haopeng Jiang [email protected]
Institute of Road and Bridge Engineering, Dalian Maritime Univ., Dalian 116026, P.R. China. Email: [email protected]
Professor, Institute of Road and Bridge Engineering, Dalian Maritime Univ., Dalian 116026, P.R. China (corresponding author). ORCID: https://orcid.org/0000-0003-4045-8799. Email: [email protected]
Fengrui Zhang [email protected]
Institute of Road and Bridge Engineering, Dalian Maritime Univ., Dalian 116026, P.R. China. Email: [email protected]

Metrics & Citations

Metrics

Citations

Download citation

If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.

Cited by

  • Creep Failure Mechanism and Model of Granite under True Triaxial Loading and Unloading Conditions, International Journal of Geomechanics, 10.1061/IJGNAI.GMENG-9622, 24, 10, (2024).

View Options

Get Access

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Get Access

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Media

Figures

Other

Tables

Share

Share

Copy the content Link

Share with email

Email a colleague

Share