Utilizing Site Investigation and Load Tests to Predict Drilled Shaft Design Parameters and Capacities for Various Geological Formations
Publication: Geo-Congress 2023
ABSTRACT
An accurate prediction of design capacities of a drilled shaft on weak rock formations is vital for a better design of deep foundations. Irregularities in rock formations due to weathering cause high inconsistency in actual bearing capacities. The assessment of bearing capacity of these rocks typically requires frequent in situ field tests such as drilled shafts load test at smaller intervals (multiple gauges) that are time consuming and expensive. The current design charts that being used in few states such as Texas and Oklahoma do not distinguish between the various types of rock or degradable materials such as intermediate geomaterials (IGM) or shale formations. This study documents several load tests such as Statnamic and bi-directional (O-cell) load cell testing (Osterberg) that were performed across the United States. The principal goal of this research is to improve methods to predict drilled shaft design capacities by accounting for the geologic formations and learning from past projects. This research developed predictive equations to shaft capacities for various rock formations.
Get full access to this article
View all available purchase options and get full access to this chapter.
REFERENCES
AASHTO, LRFD Bridge Design Specifications. 8th (2017) and 9th (2020) Edition, American Association of State Highway and Transportation Officials, Washington, DC.
Abu-Hejleh, N. M., O’Neill, M. W., Hanneman, D., and Attwooll, W. J. (2003). Improvement of the geotechnical axial design methodology for Colorado’s drilled shafts socketed in weak rocks. https://doi.org/10.3141/1936-12.
Aurora, R. P., and Reese, L. C. (1976). Behavior of axially loaded drilled shafts in clay-shales.
Dass, R. N., and Puri, V. K. “Load Tests on Drilled Shafts for Highway Bridges” (1998). International Conference on Case Histories in Geotechnical Engineering. 56. https://scholarsmine.mst.edu/icchge/4icchge/4icchge-session01/56.
Davisson, M. T. (1972). High-Capacity Piles, Proc. Soil Mechanics lecture series on Innovations in Foundation Construction, ASCE, Illinois section, Chicago, pp. 81–112.
Fellenius, B. H. (2001). What capacity value to choose from the results a static loading test. We have determined the capacity, then what? Deep Foundation Institute, Fulcrum, Winter 2001, pp. 19–22 and Fall 2001, pp. 23–26. https://www.fellenius.net/papers/230%20&%20240%20Analysis%20of%20Pile%20Capacity-DFI.pdf.
Ferrucci, M., Zellers, D., Hanna, S., Adams, R., and Moryl, J. (2019). Performance of an Osterberg Cell (O-Cell) Load Test on a High-Capacity Production Drilled Shaft at the Kosciuszko Bridge. Geo-Congress: Foundations, 199–212. https://doi.org/10.1061/9780784482094.019.
FHWA (Federal Highway Administration). “National Bridge Inventory – Highway Statistics 2020.” Office of Bridges and Structures. Last modified March 20, 2021, https://www.fhwa.dot.gov/bridge/nbi/ascii2020.cfm.
Fuller, F. M., and Hoy, H. E. (1970). “Pile load tests including quick-load test method, conventional methods, and interpretations.” Highway Research Record, (333).
Erik Loehr, J., Lutenegger, A., Rosenblad, B., and Boeckmann, A. (2016). Geotechnical Site Characterization.
Moon, N., O’Neill, M., and Vipulanandan, C. (2004). Correlation between Texas Cone Penetration (TCP) Values and Compressive Strength of Clay Shale in Texas.
Nam, M. S. (2004). Improved design for drilled shafts in rock. Ph.D. Dissertation, Department of Civil and Environmental Engineering, University of Houston, Houston.
Nam, M. S., Liang, R., Cavusoglu, E., O’Neill, M. W., Liu, R. C., and Vipulanandan, C. (2002). Improved Design Economy for Drilled Shafts in Rock-Introduction, Literature Review, Selection of Field Test Sites for Further Testing, and Hardware Prepared for TxDOT https://static.tti.tamu.edu/tti.tamu.edu/documents/0-4372-1.pdf.
Nam, M. S., and Vipulanandan, C. (2008). Roughness and Unit Side Resistances of Drilled Shafts Socketed in Clay Shale and Limestone. Journal of Geotechnical and Geoenvironmental Engineering, 134(9), 1272–1279. https://doi.org/10.1061/(asce)1090-0241(2008)134:9(1272).
Nam, M. S., and Vipulanandan, C. (2010). Relationship between Texas Cone Penetrometer Tests and Axial Resistances of Drilled Shafts Socketed in Clay Shale and Limestone. Journal of Geotechnical and Geoenvironmental Engineering, 136(8), 1161–1165. https://doi.org/10.1061/(asce)gt.1943-5606.0000318.
O’Neill, M. W., and Reese, L. C. (1999). “Drilled shafts: Construction procedures and design methods.”, Dept. of Transportation, Federal Highway Administration, Office of Implementation, McLean, VA.
O’Neill, M. W., Reese, L. C., Barnes, R., Wang, S.-T., Morvant, M., and Ochoa, M. (1992). Effects of stratigraphic and construction details on the load transfer behavior of drilled shafts. Transportation Research Record, 1336, 50–56.
Osterberg, J. O. (1998). “O-cell Testing Case Histories Demonstrate the Importance of Bored Pile (Drilled Shaft) Construction Technique,” Proceedings: Fourth International Conference on Case Histories in Geotechnical Engineering, St. Louis, MO. pp.1103–1115.
Salman, H. PhD Thesis Dissertation-University of Texas Arlington 2021 - Utilizing load tests and site investigation data to predict design load capacities for drilled shafts in different geologic formations.
TxDOT (Texas Department of Transportation). (2020). Geotechnical Manual. Austin, Texas. http://onlinemanuals.txdot.gov/txdotmanuals/geo/geo.pdf.
Thomas, M. G. (2007). Geotechnical Challenges of the Weak Shale Units of North Texas. Problematic Soils and Rocks and In Situ Characterization, 1, 1–8. https://doi.org/10.1061/40906(225)10.
USGS. Texas Geology Map. 2007. https://txpub.usgs.gov/txgeology/.
USDA. (2012). Engineering Classification of Rock Materials. Part 631. Washington DC. Natural Resources Conservation Service, U.S. Government Printing Office. https://directives.sc.egov.usda.gov/viewerFS.aspx?id=3848.
Information & Authors
Information
Published In
Geo-Congress 2023
Pages: 34 - 44
History
Published online: Mar 23, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.