Experimental and Numerical Evaluation of Older Chevron Concentrically Braced Frames with Hollow and Concrete-Filled Braces
This article has been corrected.
VIEW CORRECTIONPublication: Journal of Structural Engineering
Volume 144, Issue 3
Abstract
Detailed seismic provisions for concentrically braced frames have evolved continuously since 1988. Thus, vintage-era braced frames, especially those designed prior to 1988, may be prone to a number of significant deficiencies. These deficiencies include interdependent failures at the braces, connections, and beams, making them difficult to predict without system-level tests. An experimental study was undertaken to evaluate current retrofit provisions’ ability to predict the seismic response of pre-1988 existing braced frames. A nearly full-scale test specimen—representative of a 1985 chevron braced frame—was subjected to cyclic lateral loading. The specimen was subsequently upgraded with concrete-filled braces and retested. Test results demonstrate that pre-1988 braced frames are highly susceptible to weak-story behavior and local failure modes. Numerical models using standard nonlinear static methods predicted some, but not all, of these failures. Accordingly, recommendations to improve the efficacy of these numerical models are presented.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported by National Science Foundation (NSF) under Grant No. CMMI-1208002. The principal investigator was Charles Roeder of the University of Washington, Seattle. The work reported on herein was carried out as a subaward from this project under the supervision of the second author. Special thanks go to Dr. Jiun-Wei Lai and the many practicing engineers whose advice was invaluable to this research. The writers also wish to express their appreciation to the technical staff of the Berkeley site for the NSF George E. Brown, Jr., Network for Earthquake Engineering Simulation for its invaluable assistance. The findings, opinions, recommendations, and conclusions in this paper are those of the authors alone and do not necessarily reflect the views of others, including the sponsors.
References
AISC. (1978). Specification for the design, fabrication and erection of structural steel for buildings, Chicago.
AISC. (1990). Seismic provisions for structural steel buildings, Chicago.
AISC. (1997). Seismic provisions for structural steel buildings, Chicago.
AISC. (1999). Seismic provisions for structural steel buildings (1997), Chicago.
AISC. (2010a). “Seismic provisions for structural steel buildings.” ANSI/AISC-341-10, Chicago.
AISC. (2010b). “Specification for structural steel buildings.” ANSI/AISC-360-10, Chicago.
ASCE. (2010). “Minimum design loads for buildings and other structures.” ASCE/SEI Standard 7-10, Reston, VA.
ASCE. (2013). “Seismic evaluation and retrofit of existing buildings.” ASCE-41-13, Reston, VA.
Astaneh-Asl, A., Goel, S., and Hanson, R. (1985). “Cyclic out-of-plane buckling of double-angle bracing.” J. Struct. Eng., 1135–1153.
Astaneh-Asl, A., Liu, J., and McMullin, K. M. (2002). “Behavior and design of single plate shear connections.” J. Constr. Steel Res., 58(5–8), 1121–1141.
ASTM. (2011a). “Standard test method for compressive strength of cylindrical concrete specimens.” ASTM C39/C39M-11a, West Conshohocken, PA.
ASTM. (2011b). “Standard test method for splitting tensile strength of cylindrical concrete specimens.” ASTM C496/C496M-11, West Conshohocken, PA.
AWS (American Welding Society). (2005). “Specification for carbon steel electrodes for flux cored arc welding.” ANSI/AWS A5.20-05, Miami.
Baker, J. W., Lin, T., and Shahi, S. K. (2011). “New ground motion selection procedures and selected motions for the PEER transportation research program.”, Pacific Earthquake Engineering Research Center, Berkeley, CA.
Black, R. G., Wenger, W. A., and Popov, E. P. (1980). “Inelastic buckling of steel struts under cyclic load reversals.”, Univ. of California, Berkeley, CA.
Bradley, C., Fahnestock, L., Hines, E., and Sizemore, J. (2017). “Full-scale cyclic testing of low-ductility concentrically-braced frames.” J. Struct. Eng., 04017029.
Broderick, B. M., Elghazouli, A. Y., and Goggins, J. (2008). “Earthquake testing and response analysis of concentrically-braced sub-frames.” J. Constr. Steel Res., 64(9), 997–1007.
Brown, V. L. S. (1988). “Stability of gusseted connections in steel structures.” Ph.D. dissertation, Univ. of Delaware, Newark, DE.
Fell, B. V. (2008). “Large-scale testing and simulation of earthquake-induced ultra low cycle fatigue in bracing members subjected to cyclic inelastic buckling.” Ph.D. dissertation, Univ. of California, Davis, CA.
FEMA. (2000). “State of art report on connection performance.” FEMA-355D, Washington, DC.
Foutch, D., Goel, S., and Roeder, C. (1987). “Seismic testing of full-scale steel building—Part I.” J. Struct. Eng., 2111–2129.
Fukuta, T., Nishiyama, I., Yamanouchi, H., and Kato, B. (1989). “Seismic performance of steel frames with inverted v braces.” J. Struct. Eng., 2016–2028.
Gardner, N. J., and Jacobson, E. R. (1967). “Structural behaviour of concrete filled steel tubes.” ACI J., 64(7), 404–412.
Gross, J. L., and Cheok, G. (1988). “Experimental study of gusseted connections for laterally braced steel buildings.”, National Institute of Standards and Technology, Gaithersburg, MD.
Gugerli, H., and Goel, S. C. (1982). “Inelastic cyclic behavior of steel bracing members.”, Univ. of Michigan, Ann Arbor, MI.
Hines, E. M., Appel, M. E., and Cheever, P. J. (2009). “Collapse performance of low-ductility chevron braced steel frames in moderate seismic regions.” AISC Eng. J., 46(3), 149–180.
Hsiao, P.-C., Lehman, D. E., Berman, J. W., Roeder, C. W., and Powell, J. (2014). “Seismic vulnerability of older braced frames.” J. Perform. Constr. Facil., 108–120.
ICBO (International Conference of Building Officials). (1985). Uniform building code, Whittier, CA.
ICBO (International Conference of Building Officials). (1988). Uniform building code, Whittier, CA.
Jain, A. K., Goel, S. C., and Hanson, R. D. (1978). “Inelastic response of restrained steel tubes.” J. Struct. Div., 104(6), 897–910.
Khatib, I. F., Mahin, S. A., and Pister, K. S. (1988). “Seismic behavior of concentrically braced steel frames.”, Univ. of California, Berkeley, CA.
Lai, J. W., and Mahin, S. A. (2013). “Experimental and analytical studies on the seismic behavior of conventional and hybrid braced frames.”, Pacific Earthquake Engineering Research Center, Berkeley, CA.
Lee, K., and Bruneau, M. (2005). “Energy dissipation of compression members in concentrically braced frames: Review of experimental data.” J. Struct. Eng., 552–559.
Lehman, D., Roeder, C., Herman, D., Johnson, S., and Kotulka, B. (2008). “Improved seismic performance of gusset plate connections.” J. Struct. Eng., 890–901.
Liu, Z., and Goel, S. (1988). “Cyclic load behavior of concrete-filled tubular braces.” J. Struct. Eng., 1488–1506.
Malley, J. O. (1989). The 1988 UBC: Revisions and additions to the requirements for braced steel frames, Structural Engineers Association of California, Sacramento, CA.
McKenna, F. (1997). “Object oriented finite element programming frameworks for analysis, algorithms and parallel computing.” Ph.D. dissertation, Univ. of California, Berkeley, CA.
McManus, P. S., MacMahon, A., and Puckett, J. A. (2013). “Buckling restrained braced frame with all-bolted gusset connections.” Eng. J., 50, 89–116.
Naeim, F. (1989). The seismic design handbook, Springer, New York.
OpenSees version 2.4.6 [Computer software]. Pacific Earthquake Engineering Research Center, Berkeley, CA.
PEER and ATC (Pacific Earthquake Engineering Research Center and Applied Technology Council). (2010). “Modeling and acceptance criteria for seismic design and analysis of tall buildings.”, Berkeley/Redwood City, CA.
Rai, D. C., and Goel, S. C. (2003). “Seismic evaluation and upgrading of chevron braced frames.” J. Constr. Steel Res., 59(8), 971–994.
SEAOC (Structural Engineers Association of California). (1988). Recommended lateral force requirements, Sacramento, CA.
Sen, A. D., et al. (2016a). “Experimental evaluation of the seismic vulnerability of braces and connections in older concentrically braced frames.” J. Struct. Eng., 04016052.
Sen, A. D., et al. (2016b). “Experimental investigation of chevron concentrically braced frames with yielding beams.” J. Struct. Eng., 04016123.
Simpson, B. G., Mahin, S. A., and Lai, J. W. (2017). “Cyclic testing of older steel braced frames.”, Pacific Earthquake Engineering Research Center, Berkeley, CA.
Sloat, D. A. (2014). “Evaluation and retrofit of non-capacity designed braced frames.” M.S. thesis, Univ. of Washington, Seattle.
Stoakes, C. D., and Fahnestock, L. A. (2011). “Cyclic flexural testing of concentrically braced frame beam-column connections.” J. Struct. Eng., 739–747.
Stoakes, C. D., and Fahnestock, L. A. (2012). “Cyclic flexural analysis and behavior of beam-column connections with gusset plates.” J. Constr. Steel Res., 72, 227–239.
Tremblay, R. (2002). “Inelastic seismic response of steel bracing members.” J. Constr. Steel Res., 58(5–8), 665–701.
Tremblay, R., Bruneau, M., Nakashima, M., Prion, H. G. L., Filiatrault, A., and DeVall, R. (1996). “Seismic design of steel buildings: Lessons from the 1995 Hyogoken-Nanbu earthquake.” Can. J. Civ. Eng., 23(3), 727–756.
Tremblay, R., Timler, P., Bruneau, M., and Filiatrault, A. (1995). “Performance of steel structures during the January 17, 1994 Northridge earthquake.” Can. J. Civ. Eng., 22(2), 338–360.
Uriz, P., and Mahin, S. A. (2008). “Toward earthquake-resistance design of concentrically braced steel-frame structures.”, Pacific Earthquake Engineering Research Center, Berkeley, CA.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Feb 14, 2017
Accepted: Sep 14, 2017
Published online: Jan 10, 2018
Published in print: Mar 1, 2018
Discussion open until: Jun 10, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.