Modified Plastic-Hinge Method for Circular RC Bridge Columns
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 142, Issue 11
Abstract
This paper discusses a research program aimed at defining accurate limit-state displacements that relate to specific levels of damage in reinforced concrete bridge columns subjected to seismic hazards. In design, concrete compressive and steel tensile strain limits are related to column deformations through the use of an equivalent curvature distribution. An experimental study was carried out to assess the performance of 30 circular well-confined bridge columns. Material strains, cross-section curvatures, and fixed-end rotations attributed to strain penetration of reinforcement into the adjoining member were quantified by using a three-dimesional (3D) position monitoring system. An equivalent curvature distribution was created that reflects the measured spread of plasticity and components of deformation. When compared with the current approach, the proposed modified plastic-hinge method improved the accuracy of both tensile and compressive strain-displacement predictions, while maintaining similar levels of accuracy for elastic displacements. These recommendations, combined with material strain limits defined in the larger research program, serve as input into a displacement-based design procedure to achieve a defined level of performance under a specific seismic hazard.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors wish to acknowledge Alaska Department of Transportation and Public Facilities (DOT&PF) and Alaska University Transportation Center (AUTC), who supported this research through a series of grants. Special acknowledgement goes to Elmer Marx of Alaska DOT&PF, who was closely involved in this research as the primary technical contact.
References
Alemdar, Z. F. (2010). “Plastic hinging behavior of reinforced concrete bridge columns.” Ph.D. thesis, Univ. of Kansas, Lawrence, KS.
Baker, A. L. L., and Amarakone, A. M. N. (1964). “Inelastic hyperstatic frame analysis.” Proc., Int. Symp. on the Flexural Mechanics of Reinforced Concrete, ASCE-ACI, Reston, VA, 85–142.
Berry, M. P., Lehman, D. E., and Lowes, L. N. (2008). “Lumped-plasticity models for performance simulation of bridge columns.” ACI Struct. J., 105(3), 270–279.
Corley, W. G. (1966). “Rotational capacity of reinforced concrete beams.” J. Struct. Div., 92(ST5), 121–146.
Goodnight, J. C., Kowalsky, M. J., and Nau, J. M. (2013). “Effect of load history on performance limit states of circular bridge columns.” J. Bridge Eng., 1383–1396.
Goodnight, J. C., Kowalsky, M. J., and Nau, J. M. (2015a). “Strain limit states for circular RC bridge columns.” Earthquake Spectra, in press.
Goodnight, J. C., Kowalsky, M. J., and Nau, J. M. (2015b). “The effects of load history and design variables on performance limit states of circular bridge columns.”, Alaska DOT&PF, Juneau, AK.
Hines, E. M., Restrepo, J. I., and Seible, F. (2004). “Force-displacement characterization of well confined bridge piers.” ACI Struct. J., 101(4), 537–548.
Hines, E. M., and Seible, F. (2002). “Experimental spread of plasticity in reinforced concrete bridge piers.” Univ. of California, San Diego.
Mander, J. B. (1983). “Seismic design of bridge piers.” Ph.D. thesis, Univ. of Canterbury, Christchurch, New Zealand.
Mander, J. B., Priestley, M. J. N., and Park, R. (1988). “Theoretical stress-strain model for confined concrete.” J. Struct. Eng., 1804–1826.
Mattock, A. H. (1967). “Discussion of ‘Rotational capacity of reinforced concrete beams’ by Corley, W. G. (1966).” J. Struct. Div., 93(ST2), 519–522.
Montejo, L. A., and Kowalsky, M. J. (2007). “CUMBIA—Set of codes for the analysis of reinforced concrete members.”, North Carolina State Univ., Raleigh, NC.
Northern Digital. (2015). “OPTOTRAK certus HD dynamic measuring machine.” 〈http://www.ndigital.com/msci/products/certus-hd/〉 (Jan. 21, 2015).
Park, R., and Paulay, T. (1975). Reinforced concrete structures, Wiley, New York.
Park, R., Priestley, M. J. N., and Gill, W. D. (1982). “Ductility of square-confined concrete columns.” J. Struct. Div., 108(ST4), 929–950.
Paulay, T., and Priestley, M. J. N. (1992). Seismic design of reinforced concrete and masonry buildings, Wiley, New York.
Priestley, M. J. N., Calvi, G. M., and Kowalsky, M. J. (2007). Displacement-based seismic design of structures, IUSS Press, Pavia, Italy.
Priestley, M. J. N., and Park, R. (1987). “Strength and ductility of concrete bridge columns under seismic loading.” ACI Struct. J., 84(1), 61–76.
Sawyer, H. A. (1964). “Design of reinforced concrete frames for two failure states.” Proc., Int. Symp. on the Flexural Mechanics of Reinforced Concrete, ASCE-ACI, Reston, VA, 405–431.
Zhao, J., and Sritharan, S. (2007). “Modeling of strain penetration effects in fiber-based analysis of reinforced concrete structures.” ACI Struct. J., 104(2), 133–141.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Mar 3, 2015
Accepted: Mar 18, 2016
Published online: Jun 8, 2016
Published in print: Nov 1, 2016
Discussion open until: Nov 8, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.