Test-Based Calibration of Safety Factors for Capacity Models
Publication: Journal of Structural Engineering
Volume 142, Issue 11
Abstract
A simple procedure to calibrate the safety factor of capacity models is presented. The calibration can be carried out based on any available database of experimental tests, even of limited size. The procedure aims to assess the model capability of predicting the test results and to calibrate the safety factor so that the capacity equation meets the target reliability level required by the code or sought by the calibrator. After predicting each test of the database with the capacity equation under consideration, the test-prediction pairs are checked for the property of linearity, and the relative error for the properties of homoscedasticity and normality. Once these properties are fulfilled—which may require a nonlinear transformation of the test values and/or the predictions—the closed-form equation proposed in this paper is employed to compute a target design value. The model safety factor is finally obtained by comparing such target design value with the design value obtained from the code. The paper also proposes two approximate analytical equations to compute the tolerance factor, used to attain any given fractile, as a function of the (even small) number of tests, with any assigned confidence level. A fundamental outcome of the procedure is that it yields an objective indicator of the model accuracy, measured by the standard deviation of its error, which may be regarded as a parameter useful for selecting the most reliable model among different competing ones. In the long run, the application of the proposed procedure will allow achieving a uniform reliability level throughout all capacity models used in codes and guidelines. A further advantage is that the partial safety factors so derived can be straightforwardly updated when more experiments become available. As an example, the proposed procedure is herein applied to the ACI 318 shear design capacity equation for concrete members unreinforced in shear.
Get full access to this article
View all available purchase options and get full access to this article.
References
ACI (American Concrete Institute). (2011a). “Guide for design of anchorage to concrete: Examples using ACI 318 appendix D.” ACI 355.3R-11, Farmington Hills, MI.
ACI (American Concrete Institute). (2011b). “Guide to evaluation of strength test results of concrete.” ACI 214R-11, Farmington Hills, MI.
ACI (American Concrete Institute). (2013). “Report on nondestructive test methods for evaluation of concrete in structures.” ACI 228.2R-13, Farmington Hills, MI.
ACI (American Concrete Institute). (2014). “Building code requirements for structural concrete.” ACI 318-14, Farmington Hills, MI.
Burdekin, F. M. (2007). “General principles of the use of safety factors in design and assessment.” Eng. Fail. Anal., 14(3), 420–433.
CEN (European Committee for Standardization). (2002). “Basis of structural design.” EN-1990, Eurocode 0, Milano, Italy.
CEN (European Committee for Standardization). (2005). “Design of concrete structures. Part 1-1: General rules and rules for buildings.” EN-1992-1-1, Eurocode 2, Milano, Italy.
Goldfeld, S. M., and Quandt, R. E. (1965). “Some tests for homoscedasticity.” J. Am. Stat. Assoc., 60(310), 539–547.
Jennett, W. J., and Welch, B. L. (1939). “The control of proportion defective as judged by a single quality characteristic varying on a continuous scale.” J. R. Stat. Soc., 6(1), 80–88.
Johnson, N. L., and Welch, B. L. (1940). “Application of the non-central t-distribution.” Biometrika, 31(3–4), 362–389.
Melchers, R. E. (1987). Structural reliability. Analysis and prediction, Wiley, New York.
Montgomery, D. C., and Runger, G. C. (2011). Applied statistics and probability for engineers, Wiley, New York.
Natrella, M. G. (1963). “Experimental statistics.”, U.S. Dept. of Commerce, Washington, DC.
Reineck, K. -H., Kuchma, D. A., Kim, K. S., and Marx, S. (2003). “Shear database for reinforced concrete members without shear reinforcement.” ACI Struct. J., 100(2), 240–249.
Sedlacek, G., and Kraus, O. (2007). “Use of safety factors for the design of steel structures according to the Eurocodes.” Eng. Fail. Anal., 14(3), 434–441.
Wallis, W. A. (1947). “Use of variables in acceptance inspection for percent defective.” Selected techniques of statistical analysis, C. Eisenhart, M. W. Hastay, and W. A. Wallis, eds., McGraw Hill Book Company, New York, 7–93.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: May 28, 2015
Accepted: Mar 21, 2016
Published online: Jun 8, 2016
Published in print: Nov 1, 2016
Discussion open until: Nov 8, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.