Combined Distortional and Overall Flexural-Torsional Buckling of Cold-Formed Stainless Steel Sections: Experimental Investigations
This article is a reply.
VIEW THE ORIGINAL ARTICLEThis article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 136, Issue 4
Abstract
This paper presents a series of 48 full-scale tests on press-braked stainless steel lipped channel section columns subjected to concentric compression. The tests were carried out between fixed ends in the Structures Laboratory of the University of Liège and the test specimens were designed such that distortional buckling developed in the section prior to overall flexural-torsional buckling. The stainless steel alloy was 1.4003 chromium weldable steel, popularly known as 3Cr12. Three different geometries were tested using the same experimental setup. A critical summary of the standards and methods for calculating the carrying capacity of cold-formed stainless steel compression members is presented in a companion paper by the same writers.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
B. Rossi is supported by the Belgian National Fund for Scientific Research (FRS-FNRS), which is gratefully acknowledged. The Rotary District 1630 is also acknowledged for having granted B. Rossi its scholarship to Sydney.
References
Ala-Outinen, T., and Oksanen, T. (1997). “Stainless steel compression members exposed to fire.” Research Note No. 1864, VTT Building Technology, Finland.
Ashraf, M. (2006). “Structural stainless steel design: Resistance based on deformation capacity.” Ph.D. thesis, Imperial College, London.
Ashraf, M., Gardner, L., and Nethercot, D. A. (2006). “Finite element modeling of structural stainless steel cross-sections.” Thin-walled Struct., 44(10), 1048–1062.
Becque, J., Lecce, M., and Rasmussen, K. (2008). “The direct strength method for stainless steel compression members.” J. Constr. Steel Res., 64(11), 1231–1238.
Gardner, L., and Nethercot, D. A. (2004a). “Experiments on stainless steel hollow sections. Part 1: Material and cross-sectional behavior.” J. Constr. Steel Res., 60(9), 1291–1318.
Gardner, L., and Nethercot, D. A. (2004b). “Experiments on stainless steel hollow sections. Part 2: Member behavior of columns and beams.” J. Constr. Steel Res., 60(9), 1319–1332.
Kuwamura, H. (2003). “Local buckling of thin-walled stainless steel members.” Steel Structures, 3, 191–201.
Kyröläinen, A., Sánchez, R., Santacreu, P.-O., Picozzin, V., and Gales, A., (2003). “Stainless steels in bus constructions.” Technical Rep. No. EUR20884, Luxembourg Office for Official Publications of the European Communities, Luxembourg.
Lecce, M. (2006). “Distortional buckling of Stainless steel sections.” Ph.D. thesis, The Univ. of Sydney, Sydney, Australia.
Lecce, M., and Rasmussen, K. J. R. (2006a). “Distortional buckling of cold-formed stainless steel sections: Experimental investigation.” J. Struct. Eng., 132(4), 497–504.
Lecce, M., and Rasmussen, K. J. R. (2006b). “Distortional buckling of cold-formed stainless steel sections: Finite-element modeling and design.” J. Struct. Eng., 132(4), 505–514.
Liu, Y., and Young, B. (2003). “Buckling of stainless steel square hollow section compression members.” J. Constr. Steel Res., 59(2), 165–177.
Rossi, B. (2008). “Mechanical properties, residual stresses and structural behavior of thin-walled stainless steel profiles.” Ph.D. thesis, Univ. of Liège, Liège, Belgium.
Rossi, B. J.-P., J., and Rasmussen, K. J. R. (2010). “Combined distortional and overall flexural-tortional buckling of cold-formed stainless steel sections: Design.” J. Struct. Eng. 136(4), 361–369.
Schepens, M. (2008). “Etude de profilés à parois minces en acier inoxydable.” Graduation thesis, Univ. of Liège, Liège, Belgium.
Talja, A., and Salmi, P. (1995). “Design of stainless steel RHS beams: columns and beam-columns.” Research Note No. 1619, VTT Building Technology, VTT Technical Research Centre of Finland, Finland.
Young, B., and Liu, Y. H. (2003). “Experimental investigation of cold-formed stainless steel columns.” J. Struct. Eng., 129(2), 169–176.
Information & Authors
Information
Published In
Copyright
© 2010 ASCE.
History
Received: Jan 7, 2009
Accepted: Aug 24, 2009
Published online: Oct 8, 2009
Published in print: Apr 2010
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.