Ultimate Bearing Capacity of Helical Piles as Electric Transmission Tower Foundations in Unsaturated Soils: Analytical, Numerical, and Experimental Investigations
Publication: International Journal of Geomechanics
Volume 22, Issue 11
Abstract
In this paper, the compressive and tensile ultimate bearing capacity of helical piles, in the load range required for designing 63-kV transmission towers, are studied by conducting analytical and numerical investigations. In this light, an explicit easy-to-use analytical framework was developed by considering the unsaturated soil condition that was validated against experimental records. Also, finite-element models were constructed for fully saturated and fully dry soil conditions. Then, to validate the analytical and numerical solutions in fully saturated and fully dry soil conditions, three compressive and one tensile field tests were carried out, and the results were compared quantitatively with analytical and numerical calculations. Comparative studies showed that the analytical, numerical, and experimental results have a high level of conformity. In accordance with the load ranges of transmission towers, analytical parametric studies were conducted for different geometrical aspects of the helical piles in different soils. Also, for two typical unsaturated sand and clay soils, the ultimate load of helical piles was calculated versus matric suction. Moreover, a vast numerical parametric study was performed to investigate the role of the geometrical aspects of helical piles and soil characteristics on the load-transfer mechanism and ultimate bearing-capacity values for helical piles driven in sandy and undrained saturated clayey soils. Results showed that the maximum load capacity of helical piles occurred in a matric suction less than that of a fully dry soil. In addition, the soil type and the geometrical aspects of the helical pile were shown to have significant effects on the load–displacement behavior and ultimate bearing-capacity values.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was financially supported by the Niroo Research Institute (NRI) of Iran, which is greatly acknowledged.
References
Al-Baghdadi, T. A., M. J. Brown, J. A. Knappett, and A. H. Al-Defae. 2017. “Effects of vertical loading on lateral screw pile performance.” Proc. Inst. Civ. Eng. Geotech. Eng. 170 (3): 259–272. https://doi.org/10.1680/jgeen.16.00114.
ASTM. 2007a. Standard test methods for deep foundations under static axial compressive load. ASTM 1143/D1143M-07. Annual Book of ASTM Standards. West Conshohocken, PA: ASTM.
ASTM. 2007b. Standard test methods for deep foundations under static axial tensile load. ASTM D3689-07. Annual Book of ASTM Standards. West Conshohocken, PA: ASTM.
Bishop, A. W. 1959. “The principle of effective stress.” Teknik Ukeblad 39: 859–863.
Brown, D. A., J. P. Turner, R. J. Castelli, and P. B. Americas. 2010. Drilled shafts: Construction procedures and LRFD design methods. FHWA-NHI-10-016. Washington, DC: Federal Highway Administration.
Budhu, M. 2010. Soil mechanics and foundations. 3rd ed. Hoboken, NJ: Wiley.
Byrne, B. W., and G. T. Houlsby. 2015. “Helical piles: An innovative foundation design option for offshore wind turbines.” Philos. Trans. R. Soc. London, Ser. A 373 (2035): 20140081. https://doi.org/10.1098/rsta.2014.0081.
Carter, M., and S. P. Bentley. 2016. Correlations of soil properties. Hoboken, NJ: Wiley.
CGS (Canadian Geotechnical Society). 2006. Canadian foundation engineering manual. 4th ed. Vancouver, BC: CGS c/o BiTech Publishers.
Darin Willis, P. E. 2010. “How to design helical piles per the 2009 international building code.” Ram Jack Foundation Solution. Accessed April 2, 2014. http://www.foundationrepairnetwork.com/design-helical-piles.pdf.
Dib, M., S. Kouloughli, and M. Hecini. 2019. “Numerical analysis of high capacity helical piles subjected to ground movement in weathered unstable clayey slope.” Comput. Geotech. 110: 319–325. https://doi.org/10.1016/j.compgeo.2019.01.024.
Donal, J., and P. E. Calyton. 2005. Basic helical screw pile design. ECP torque Anchor Brand of helical screw piles, 1–28. Olathe, KS: Earth Contact Products Company.
Elkasabgy, M., and M. H. El Naggar. 2015. “Axial compressive response of large-capacity helical and driven steel piles in cohesive soil.” Can. Geotech. J. 52 (2): 224–243. https://doi.org/10.1139/cgj-2012-0331.
El Sharnouby, M. M., and M. H. El Naggar. 2012. “Field investigation of axial monotonic and cyclic performance of reinforced helical pulldown micropiles.” Can. Geotech. J. 49 (5): 560–573. https://doi.org/10.1139/t2012-017.
Elsherbiny, Z. H., and M. H. El Naggar. 2013. “Axial compressive capacity of helical piles from field tests and numerical study.” Can. Geotech. J. 50 (12): 1191–1203. https://doi.org/10.1139/cgj-2012-0487.
Fahmy, A., and M. H. El Naggar. 2017. “Axial performance of helical tapered piles in sand.” Geotech. Geol. Eng. 35 (4): 1549–1576. https://doi.org/10.1007/s10706-017-0192-1.
Fateh, A. M. A., A. Eslami, and A. Fahimifar. 2018. “A study of the axial load behaviour of helical piles in sand by frustum confining vessel.” Int. J. Phys. Modell. Geotech. 18 (4): 175–190. https://doi.org/10.1680/jphmg.16.00007.
Garakani, A. A. 2013. “Laboratory assessment of the hydro-mechanical behavior of unsaturated undisturbed collapsible soils – Case study: Gorgan Loess.” Ph.D. thesis, Dept. of Civil Engineering, Sharif Univ. of Technology.
Garakani, A. A. 2020. Compilation of technical knowledge for mechanical design, execution and testing of helical piles in 63 kV lattice towers. [In Farsi.] Tehran, Iran: Niroo Research Institute.
Garakani, A. A., M. M. Birgani, and H. Sadeghi. 2021a. “An effective stress-based parametric study on the seismic stability of unsaturated slopes with implications for preliminary microzonation.” Bull. Eng. Geol. Environ. 80 (10): 7525–7549. https://doi.org/10.1007/s10064-021-02440-x.
Garakani, A. A., S. M. Haeri, D. Y. Cherati, F. A. Givi, M. K. Tadi, A. H. Hashemi, N. Chiti, and F. Qahremani. 2018. “Effect of road salts on the hydro-mechanical behavior of unsaturated collapsible soils.” Transp. Geotech. 17: 77–90. https://doi.org/10.1016/j.trgeo.2018.09.005.
Garakani, A. A., S. M. Haeri, C. S. Desai, S. M. H. S. Ghafouri, B. Sadollahzadeh, and H. H. Senejani. 2019. “Testing and constitutive modeling of lime-stabilized collapsible loess. II: Modeling and validations.” Int. J. Geomech. 19 (4): 4019007. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001386.
Garakani, A. A., S. M. Haeri, A. Khosravi, and G. Habibagahi. 2015. “Hydro-mechanical behavior of undisturbed collapsible loessial soils under different stress state conditions.” Eng. Geol. 195: 28–41. https://doi.org/10.1016/j.enggeo.2015.05.026.
Garakani, A. A., and J. Maleki. 2020. “Load capacity of helical piles with different geometrical aspects in sandy and clayey soils: A numerical study.” In Proc., Int. Congress and Exhibition, Sustainable Civil Infrastructures, 73–84. Cham, Switzerland: Springer.
Garakani, A. A., A. Pirjalili, and C. S. Desai. 2021b. “An effective stress-based DSC model for predicting the coefficient of lateral soil pressure in unsaturated soils.” Acta Geotech. 16 (12): 3813–3830. https://doi.org/10.1007/s11440-021-01376-6.
Garakani, A. A., H. Sadeghi, S. Saheb, and A. Lamei. 2020. “Bearing capacity of shallow foundations on unsaturated soils: Analytical approach with 3D numerical simulations and experimental validations.” Int. J. Geomech. 20 (3): 4019181. https://doi.org/10.1061/(asce)gm.1943-5622.0001589.
Gavin, K., P. Doherty, and A. Tolooiyan. 2014. “Field investigation of the axial resistance of helical piles in dense sand.” Can. Geotech. J. 51 (11): 1343–1354. https://doi.org/10.1139/cgj-2012-0463.
George, B. E., S. Banerjee, and S. R. Gandhi. 2019. “Helical piles installed in cohesionless soil by displacement method.” Int. J. Geomech. 19 (7): 04019074. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001457.
George, B. E., S. Banerjee, and S. R. Gandhi. 2020. “Numerical analysis of helical piles in cohesionless soil.” Int. J. Geotech. Eng. 14 (4): 361–375. https://doi.org/10.1080/19386362.2017.1419912.
Ghaly, A., and A. Hanna. 1994. “Model investigation of the performance of single anchors and groups of anchors.” Can. Geotech. J. 31 (2): 273–284. https://doi.org/10.1139/t94-032.
Haeri, S. M., A. A. Garakani, and M. Kamali Zarch. 2021. “Unsaturated 3D column method: New method for evaluation of stability of unsaturated slopes subjected to vertical steady-state infiltration and evaporation.” Int. J. Geomech. 21 (10): 04021177. https://doi.org/10.1061/(ASCE)GM.1943-5622.0002125.
Haeri, S. M., A. A. Garakani, A. Khosravi, and C. L. Meehan. 2014. “Assessing the hydro-mechanical behavior of collapsible soils using a modified triaxial test device.” Geotech. Test. J. 37 (2): 20130034. https://doi.org/10.1520/gtj20130034.
Haeri, S. M., A. A. Garakani, H. R. Roohparvar, C. S. Desai, S. M. H. S. Ghafouri, and K. S. Kouchesfahani. 2019. “Testing and constitutive modeling of lime-stabilized collapsible loess. I: Experimental investigations.” Int. J. Geomech. 19 (4): 4019006. https://doi.org/10.1061/(asce)gm.1943-5622.0001364.
Haeri, S. M., A. Khosravi, A. A. Garakani, and S. Ghazizadeh. 2017. “Effect of soil structure and disturbance on hydromechanical behavior of collapsible loessial soils.” Int. J. Geomech. 17 (1): 04016021. https://doi.org/10.1061/(asce)gm.1943-5622.0000656.
Hanna, A., T. Ayadat, and M. Sabry. 2007. “Pullout resistance of single vertical shallow helical and plate anchors in sand.” Geotech. Geol. Eng. 25 (5): 559–573. https://doi.org/10.1007/s10706-007-9129-4.
IrPBO (Iran's Planning and Budget Organization). 2008. General technical specification and execution procedures for transmission and subtransmission networks concrete foundation of overhead line structures - Code 431. [In Farsi.] Tehran, Iran: Office of Deputy for Strategic Supervision, Bureau of Technical Execution System, Plan and Budget Organization.
Khalili, N., and M. H. Khabbaz. 1998. “A unique relationship for χ for the determination of the shear strength of unsaturated soils.” Géotechnique 48 (5): 681–687. https://doi.org/10.1680/geot.1998.48.5.681.
Kurian, N. P., and S. J. Shah. 2009. “Studies on the behaviour of screw piles by the finite element method.” Can. Geotech. J. 46 (6): 627–638. https://doi.org/10.1139/T09-008.
Li, W., and L. Deng. 2019. “Axial load tests and numerical modeling of single-helix piles in cohesive and cohesionless soils.” Acta Geotech. 14 (2): 461–475. https://doi.org/10.1007/s11440-018-0669-y.
Livneh, B., and M. H. El Naggar. 2008. “Axial testing and numerical modeling of square shaft helical piles under compressive and tensile loading.” Can. Geotech. J. 45 (8): 1142–1155. https://doi.org/10.1139/T08-044.
Lu, N., and W. J. Likos. 2004. Unsaturated soil mechanics. Hoboken, NJ: Wiley.
Mahmood, M. R., N. M. Salim, and A. A. Al-Gezzy. 2021. “Effect of different soil saturation conditions on the ultimate uplift resistance of helical pile model.” E3S Web Conf. 318; 01012. https://doi.org/10.1051/e3sconf/202131801012.
Merifield, R. S. 2011. “Ultimate uplift capacity of multiplate helical type anchors in clay.” J. Geotech. Geoenviron. Eng. 137 (7): 704–716. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000478.
Mitsch, M., and S. Clemence. 1985. “The uplift capacity of helix anchors in sand.” In Proc., Uplift Behaviour of Anchor Foundations in Soil, edited by S. Clemence, 26–47.
Mohajerani, A., D. Bosnjak, and D. Bromwich. 2016. “Analysis and design methods of screw piles: A review.” Soils Found. 56 (1): 115–128. https://doi.org/10.1016/j.sandf.2016.01.009.
Mooney, J. S., S. Adamczak, and S. P. Clemence. 1985. “Uplift capacity of helical anchors in clay and silt.” In Uplift behavior of anchor foundations in soil, 48–72. Detroit: ASCE.
Nasr, M. 2009. “Performance-based design for helical piles.” In Contemporary Topics in Deep Foundations, Geotechnical Special Publication 185, edited by M. Iskander, D. F. Laefer, and M. H. Hussein, 496–503. Reston, VA: ASCE.
Perko, H. A. 2009. Helical piles: A practical guide to design and installation. Hoboken, NJ: Wiley.
Rao, S. N., Y. Prasad, and M. Shetty. 1991. “The behaviour of model screw piles in cohesive soils.” Soils Found. 31 (2): 35–50. https://doi.org/10.3208/sandf1972.31.2_35.
Stas, C. V., and F. H. Kulhawy. 1984. Critical evaluation of design methods for foundations under axial uplift and compression loading. Final Rep. EPRI-EL-3771. Geotechnical Engineering Group. Ithaca, NY: Cornell Univ.
Tappenden, K., D. Sego, and P. Robertson. 2009. “Load transfer behavior of full-scale instrumented screw anchors.” In Contemporary Topics in Deep Foundations, Geotechnical Special Publication 185, edited by M. Iskander, D. F. Laefer, and M. H. Hussein, 472–479. Reston, VA: ASCE.
Tsuha, C. D. H. C., N. Aoki, G. Rault, L. Thorel, and J. Garnier. 2007. “Physical modelling of helical pile anchors.” Int. J. Phys. Modell. Geotech. 7 (4): 1–12. https://doi.org/10.1680/ijpmg.2007.070401.
Tsuha, C. D. H. C., N. Aoki, G. Rault, L. Thorel, and J. Garnier. 2012. “Evaluation of the efficiencies of helical anchor plates in sand by centrifuge model tests.” Can. Geotech. J. 49 (9): 1102–1114. https://doi.org/10.1139/t2012-064.
Tsuha, C. D. H. C., J. M. S. M. dos Santos Filho, and T. d. C. Santos. 2016. “Helical piles in unsaturated structured soil: A case study.” Can. Geotech. J. 53 (1): 103–117. https://doi.org/10.1139/cgj-2015-0017.
van Genuchten, M. T. 1980. “A closed from equation for predicting the hydraulic conductivity of unsaturated soils.” Soil Sci. Soc. Am. J. 44 (5): 892–898. https://doi.org/10.2136/sssaj1980.03615995004400050002x.
Wang, B., H. Moayedi, H. Nguyen, L. K. Foong, and A. S. A. Rashid. 2020. “Feasibility of a novel predictive technique based on artificial neural network optimized with particle swarm optimization estimating pullout bearing capacity of helical piles.” Eng. Comput. 36 (4): 1315–1324. https://doi.org/10.1007/s00366-019-00764-7.
Zhang, D. J. 1999. “Predicting capacity of helical screw piles in Alberta soils.” M.Sc. thesis, Dept. of Civil and Environmental Engineering, Univ. of Alberta.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 22 • Issue 11 • November 2022
Copyright
© 2022 American Society of Civil Engineers.
History
Received: May 7, 2021
Accepted: Jun 12, 2022
Published online: Aug 23, 2022
Published in print: Nov 1, 2022
Discussion open until: Jan 23, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Ammar Alnmr, Richard Paul Ray, Rashad Alsirawan, A State-of-the-Art Review and Numerical Study of Reinforced Expansive Soil with Granular Anchor Piles and Helical Piles, Sustainability, 10.3390/su15032802, 15, 3, (2802), (2023).