Determination of Composite Slab Strength Using a New Elemental Test Method
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 133, Issue 9
Abstract
Composite slabs utilizing cold-formed profiled steel decks are commonly used for floor systems in steel framed buildings. The behavior and strength of composite slabs are normally controlled by the horizontal shear bond between the steel deck and the concrete. The strength of the horizontal shear bond depends on many factors and it is not possible to provide representative design values that can be applied to all slab conditions a priori. Thus, present design standards require that the design parameters be obtained from full-size bending tests, which are typically one or two deck panels wide and a single span. However, because these full-size tests can be expensive and time consuming, smaller size specimens, referred to as elemental tests, are desirable and have been the subject of a great deal of research. Details for a new elemental test method for composite slab specimens under bending are presented. Test results consisting of maximum applied load, end slips, and failure modes are presented and compared with the results of full-size specimens with similar end details, spans, etc. It is shown that the performance of the elemental test developed in this study is in good agreement with the performance of the full-size specimens. Application of test data to current design specifications is also presented.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The support provided by the Univ. Teknologi Malaysia enabled the first writer to complete his graduate coursework and research at Virginia Tech.
References
Abdullah, R. (2004). “Experimental evaluation and analytical modeling of shear bond in composite slab.” Ph.D. dissertation, Virginia Polytechnic Institute and State Univ., Blacksburg, Va.
Abdullah, R., and Easterling, W. S. (2003). “Structural evaluation of a new composite deck profile: Phase II.” Rep. No. CEE/VPI-ST03/01, Virginia Polytechnic Institute and State Univ., Blacksburg, Va.
Airumyan, E., Belyaev, V., and Rumyancev, I. (1990). “Efficient embossment for corrugated steel sheeting.” IABSE Symp. on Mixed Structures Including New Materials, Brussels, Belgium, 137–142.
American Society of Civil Engineers (ASCE). (1992). “Standard for the structural design of composite slabs.” ANSI/AASCE 3-91, New York.
An, L. (1993). “Load bearing capacity and behaviour of composite slabs with profiled steel sheet.” Ph.D. dissertation, Chalmers Univ. of Technology, Göteborg, Sweden.
British Standard Institution (BSI). (1994). “Structural use of steelwork in building—Part 4: Code of practice for design of composite slabs with profiled steel sheeting.” BS-5950, London.
Burnet, M. (1998). “Analysis of composite steel and concrete flexural members that exhibit partial shear connection.” Ph.D. thesis, Univ. of Adelaide, Adelaide, Australia.
Canadian Sheet Steel Building Institute (CSSBI). (1996). “Standard for composite steel deck.” CSSBI 12M-96, Rexdale, Ont., Canada.
Chen, S. (2003). “Load carrying capacity of composite slabs with various end constraints.” J. Constr. Steel Res., 59(3), 385–403.
Daniels, B. J. (1988). “Shear bond pull-out tests for cold-formed-steel composite slabs.” ICOM-Construction Metallique, Department de Genie Civil, Ecole Polytechnique Federale de Lausanne, Lausanne, Switzerland.
Easterling, W. S., and Young, C. S. (1992). “Strength of composite slabs.” J. Struct. Eng., 118(9), 2370–2389.
European Committee for Standardization (ECS). (1994). “Design of composite steel and concrete structures. Part 1.1: General rules and rules for buildings.” Eurocode 4, ENV 1994-1-1:1992, Brussels, Belgium.
Jolly, C. K., and Zubair, A. K. (1987). “The efficiency of shear-bond interlock between profiled steel sheeting and concrete.” Proc., Int. Conf. on Steel and Aluminum Structures Composite Steel Structures, Advances, Design and Construction, Cardiff, Wales, U.K., 127–136.
Patrick, M., and Poh, K. W. (1990). “Controlled test for composite slab design parameters.” IABSE Symp., Brussels, Belgium-Mixed Structures, Including New Materials, Zurich, Switzerland, 227–231.
Plooksawasdi, S. (1977). “Evaluation and design formulations for composite steel deck.” Ph.D. dissertation, West Virginia Univ., Morgantown, W.Va.
Porter, M. L., and Ekberg, C. E. (1978). Compendium of ISU research conducted on cold-formed steel deck-reinforced slab systems, Engineering Research Institute, Iowa State Univ., Ames, Iowa.
Stark, J. (1978). “Design of composite floors with profiled steel sheet.” Proc., 4th Int. Specialty Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Rolla, Mo., 893–992.
Terry, A. S., and Easterling, W. S. (1994). “The effect of typical construction details on the strength of composite slabs.” Rep. No. CE/VPI-ST 94/05, Dept. of Civil Engineering, Virginia Polytechnic Institute and State Univ., Blacksburg, Va.
Tremblay, R., Rogers, C. A., Gignac, P., and Degrange, G. (2002). “Variables effecting the shear-bond resistance of composite floor deck systems.” Proc., 16th Int. Specialty Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Rolla, Mo., 663–676.
Veljkovic, M. (1996). “Behaviour and resistance of composite slabs.” Ph.D. thesis, Lulea Univ. of Technology, Lulea, Sweden.
Veljkovic, M. (1998). “Influence of load arrangement on composite slab behaviour and recommendations for design.” J. Constr. Steel Res., 45(2), 149–178.
Wright, H. D., and Veljkovic, M. (1996). “Towards a numerical procedure for composite slab assessment.” Proc., 13th Int. Specialty Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Rolla, Mo., 415–435.
Zubair, A. K. M. (1989). “Improvement of shear-bond in composite steel and concrete floor slabs.” Ph.D. thesis, Univ. of Southampton, Southampton, U.K.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Jul 22, 2005
Accepted: Feb 27, 2007
Published online: Sep 1, 2007
Published in print: Sep 2007
Notes
Note. Associate Editor: Brian Uy
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.