Characterization of the Stiffness of Unbound Materials for Pavement Design: Do We Follow the Right Approach?
Publication: Journal of Transportation Engineering
Volume 140, Issue 4
Abstract
Two main approaches have been followed to determine the modulus of unbound materials in six asphalt pavement sections tested at the CEDEX test track. The first one consists on back-calculation from the deflection bowls measured under the load of a falling weight deflectometer. In the second approach, a nonlinear constitutive relationship is calibrated from repeated load triaxial testing, and layer modulus is estimated through this relationship for the stresses calculated under traffic loads by using a multilayer linear elastic model. Significant differences were found between the two procedures, with back-calculation resulting in higher modulus. The two approaches were evaluated by comparing model predictions to actual response measured under the load of the traffic simulation vehicles of the test track. The results indicate that back-calculation provided more realistic estimations of the stiffness of unbound materials than the laboratory approach. This last approach significantly underestimated the stiffness of granular materials located at shallow depths in the pavement structure.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Results presented here come from a full-scale experiment that was funded by the Spanish General Road Directorate. The authors of this paper would like to express their gratitude to this institution.
References
AASHTO. (2007). “Standard method of test for determining the resilient modulus of soils and aggregate materials.” T 307-99, Washington, DC.
AASHTO. (2008). “Mechanistic-empirical pavement design guide, interim edition: A manual of practice.” Washington, DC.
De Jong, L., Peutz, M. G. F., and Korswagen, A. R. (1979). Computer program BISAR, layered systems under normal and tangential surface loads, Koninklijke/Shell-Laboratorium, Amsterdam, Netherlands.
Evercalc 5.20 [Computer software]. Washington State Dept. of Transportation Materials Laboratory, Olympia, WA.
Hoff, I., Nordal, S., and Nordal, R. S. (1999). “Constitutive model for unbound granular materials based on hyperelasticity.” Unbound granular materials—laboratory testing, in-situ testing and modelling, A. Gomes Correia, ed., A. A. Balkema, Rotterdam, Netherlands, 187–196.
Huang, H. (1993). Pavement analysis and design, Prentice Hall, Englewood Cliffs, NJ.
Ji, Y., Siddiki, N., Nantung, T., and Kim, D. (2012). “Effect of moisture variation on subgrade and base material MR design values and its implementation in MEPDG.” Proc., Transportation Research Board 91st Annual Meeting, Transportation Research Board, Washington, DC.
Mateos, A., Ayuso, J., Cadavid, B., and Marrón, J. (2012a). “Lessons learned from the application of CalME asphalt fatigue model to experimental data from CEDEX test track.” Advances in Pavement Design through Full-scale Accelerated Pavement Testing, Taylor & Francis Group, London.
Mateos, A., Ayuso, J., and Cadavid, B. (2012b). “Evolution of asphalt mixture stiffness under the combined effects of damage, aging and densification under traffic.”, Transportation Research Board, Washington, DC, 185–194.
Nazarian, S., Rojas, J., Pezo, R., Yuan, D., Abdallah, I., and Scullion, T. (1998). “Relating laboratory and field moduli of Texas base materials.”, Transportation Research Board, Washington, DC, 1–11.
Parker, F., and Elton, D. J. (1990). Methods for evaluating resilient moduli of paving materials, Auburn Univ. Highway Research Center, Auburn, AL.
Pérez Ayuso, J., Cadavid, B., and Mateos, A. (2008). “Managing data from instrumentation in the CEDEX test track.” Proc., 3rd Int. Conf. on Accelerated Pavement Testing, Transportation Research Board, Madrid.
Ping, W. V., Yang, Z., and Gao, Z. (2002). “Field and laboratory determination of granular subgrade moduli.” J. Perform. Constr. Facil., 149–159.
Rahim, A. A., and George, K. P. (2003). “Falling weight deflectometer for estimating subgrade elastic moduli.” J. Transp. Eng., 100–107.
Seeds, S. B., Alavi, S. H., Ott, W. C., Mikhail, M., and Mactutis, J. A. (2000). “Evaluation of laboratory determined and nondestructive test based resilient modulus values from the westrack experiment.” Nondestructive testing and backcalculation of moduli, ASTM, West Conshohocken, PA.
Soares, J. B., Mateos, A., and Goretti da Motta, L. M. (2009). “Aspectos gerais de métodos de dimensionamento de pavimentos asfálticos de vários países e a relação com um novo método Brasileiro.” Revista Pavimentação, 4(14), 20–35 (in Portuguese).
Ullidtz, P. (1997). “Modelling of granular materials using the discrete element method.” Proc., 8th Int. Conf. on Asphalt Pavements, International Society for Asphalt Pavements, Lino Lakes, MN.
Uzan, J. (1985). “Characterization of granular materials.”, Transportation Research Board, Washington, DC, 52–59.
Uzan, J. (1992). “Resilient characterization of pavement materials.” Int. J. Numer. Anal. Meth. Geomech., 16(6), 453–459.
Von Quintus, H. R., and Killingsworth, B. (1997). “Design pamphlet for the determination of design subgrade in support of the AASHTO guide for the design of pavement structures.”, Federal Highway Administration, McLean, VA.
Von Quintus, H. R., and Killingsworth, B. (1998). “Analyses relating to pavement material characterizations and their effects on pavement performance.”, Federal Highway Administration, McLean, VA.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: May 21, 2013
Accepted: Nov 7, 2013
Published online: Jan 6, 2014
Published in print: Apr 1, 2014
Discussion open until: Jun 6, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.