Shear Mechanisms in Reinforced Concrete Beams under Impact Loading
Publication: Journal of Structural Engineering
Volume 143, Issue 9
Abstract
A well-instrumented drop-weight test program was developed to investigate shear failure modes of large-scale RC beams under impact loading. Test variables included beam span, transverse reinforcement ratio, impact mass, and impact velocity. The impact and reaction forces, and midspan deflection and accelerations at discrete locations along the beam were measured, and crack propagation was recorded using a high-speed video camera. Nonlinear finite element simulations also were carried out to study the feasibility of modern commercial software to reproduce observed behavior. Findings from the study indicate that as the impact velocity increases, specimens tend to fail in shear with diagonal cracks forming a shear plug near the loading point. These major diagonal cracks develop within a very short duration after impact when stress wave propagation has a significant influence on the impact responses, causing them to deviate from well-known behavior under static loading conditions. Providing additional transverse reinforcement was found to inhibit the development of shear cracks and the effect of stress wave propagation on impact response was more pronounced with increasing beam span.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge the financial support provided for this research by the Major Project of National Key R&D Plan of China (2016YFC0701400) and the Natural Science Foundation of China (No. 51338004).
References
Bhatti, A. Q., Kishi, N., and Mikami, H. (2011). “An applicability of dynamic response analysis of shear-failure type RC beams with lightweight aggregate concrete under falling-weight impact loading.” Mater. Struct., 44(1), 221–231.
Bhatti, A. Q., Kishi, N., Mikami, H., and Ando, T. (2009). “Elasto-plastic impact response analysis of shear-failure-type RC beams with shear rebars.” Mater. Des., 30(3), 502–510.
Comité Euro-International du Béton. (1988). “Concrete structures under impact and impulsive loading.”, Comité Euro-International du Béton, Lausanne, Switzerland.
Cotsovos, D., Stathopoulos, N., and Zeris, C. (2008). “Behavior of RC beams subjected to high rates of concentrated loading.” J. Struct. Eng., 1839–1851.
Cotsovos, D. M. (2010). “A simplified approach for assessing the load-carrying capacity of reinforced concrete beams under concentrated load applied at high rates.” Int. J. Impact Eng., 37(8), 907–917.
Feldman, A., and Siess, C. P. (1956). “Investigation of resistance and behavior of reinforced concrete members subjected to dynamic loading.”, Civil Engineering Studies, Univ. of Illinois, Urbana-Champaign, Champaign, IL.
Feldman, A., and Siess, C. P. (1958). “Investigation of resistance and behavior of reinforced concrete members subjected to dynamic loadings: PART II.”, Civil Engineering Studies, Univ. of Illinois, Urbana-Champaign, Champaign, IL.
Fujikake, K., Li, B., and Soeun, S. (2009). “Impact response of reinforced concrete beam and its analytical evaluation.” J. Struct. Eng., 938–950.
Fujikake, K., Senga, T., Ueda, N., Ohno, T., and Katagiri, M. (2006). “Study on impact response of reactive powder concrete beam and its analytical model.” J. Adv. Concr. Technol., 4(1), 99–108.
Hallquist, J. O. (2006). LS-DYNA theory manual, Livermore Softerware Technology Corporation, Livermore, CA.
Kishi, N., and Mikami, H. (2012). “Empirical formulas for designing reinforced concrete beams under impact loading.” ACI Struct. J., 109(4), 509–519.
Kishi, N., Mikami, H., Matsuoka, K., and Ando, T. (2002). “Impact behavior of shear-failure-type RC beams without shear rebar.” Int. J. Impact Eng., 27(9), 955–968.
Kishi, N., Nakano, O., Matsuoka, K. G., and Anto, T. (2001). “Experimental study on ultimate strength of flexural-failure-type RC beams under impact loading.” Transactions of 16th Int. Conf. on Structural Mechanics in Reactor Technology, International Association for Structural Mechanics in Reactor Technology, Raleigh, NC.
Krauthammer, T., Shahriar, S., and Shanaa, H. (1990). “Response of reinforced concrete elements to severe impulsive loads.” J. Struct. Eng., 1061–1079.
LS-DYNA version 971 [Computer software]. Livermore Software Technology, Livermore, CA.
LSTC (Livermore Software Technology Corp.). (2006). LS-DYNA keyword user’s manual, Livermore, CA.
Murray, Y. D. (2007). “Users manual for LS-DYNA concrete material model 159.”, Federal Highway Administration, McLean, VA.
Ožbolt, J., and Sharma, A. (2011). “Numerical simulation of reinforced concrete beams with different shear reinforcements under dynamic impact loads.” Int. J. Impact Eng., 38(12), 940–950.
Saatci, S., and Vecchio, F. J. (2009a). “Effects of shear mechanisms on impact behavior of reinforced concrete beams.” ACI Struct. J., 106(1), 78–86.
Saatci, S., and Vecchio, F. J. (2009b). “Nonlinear finite element modeling of reinforced concrete structures under impact loads.” ACI Struct. J., 106(5), 717–725.
Tachibana, S., Masuya, H., and Nakamura, S. (2010). “Performance based design of reinforced concrete beams under impact.” Nat. Hazards Earth Syst. Sci., 10(6), 1069–1078.
Wu, K., and Yu, T. (2001). “Simple dynamic models of elastic-plastic structures under impact.” Int. J. Impact Eng., 25(8), 735–754.
Yi, W. J., Zhao, D. B., and Kunnath, S. K. (2016). “Simplified approach for assessing shear resistance of reinforced concrete beams under impact loads.” ACI Struct. J., 113(4), 747–756.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Jul 22, 2016
Accepted: Feb 21, 2017
Published online: May 11, 2017
Published in print: Sep 1, 2017
Discussion open until: Oct 11, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.