Shear Strength of Unstiffened Steel I-Section Members
Publication: Journal of Structural Engineering
Volume 143, Issue 3
Abstract
Ultimate shear strengths of 20 unstiffened I-girder specimens from the literature and seven new specimens designed to fill gaps in the experimental data are compared with predictions from models recommended by Basler, Höglund, and Lee and colleagues. Basler’s model, which is based solely on an idealized web shear buckling resistance, is shown to be accurate for webs with slenderness between 60 and 100. However, it is very conservative for members with typical plate girder web slenderness ratios. Höglund’s methods, which aim to characterize the shear postbuckling capacity of unstiffened webs, are found to be accurate to conservative. The method by Lee and colleagues, which aims to predict the shear postbuckling strength of webs with widely spaced stiffeners, is accurate on average. However, this method significantly overpredicts the strength of several specimens. A proposed adaptation of Höglund’s recommendations from a 1997 article matches the current AISC shear buckling strength equations for stocky web panels, is very simple to apply, and provides predictions that are in between those of Höglund’s methods. This adaptation of Höglund’s equations gives shear resistances that are as high as 3.66 times the capacity from Basler’s model. The specific characteristics of the different shear resistance equations are discussed, and recommendations for potential further improvement are offered. The interaction between the shear and moment capacities is found to be insignificant, although many of the specimens are subjected simultaneously to shears and moments close to the calculated nominal strengths. Resistance factors are computed to facilitate potential inclusion in modern specifications.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors are thankful for the financial support provided by the Metal Building Manufacturers Association (MBMA) and American Institute of Steel Construction. They are also thankful for the guidance provided by the MBMA Steering Committee and for the laboratory assistance from Mr. Robert Day and Ms. Qiana Flewellen of the University of Kentucky.
References
AASHTO. (2014). LRFD bridge design specifications, Washington, DC.
AISC. (2010). “Specification for structural steel buildings.”, Chicago.
AISC. (2016). “Specification for structural steel buildings.”, Chicago.
ASCE. (1971). Plastic design in steel: A guide and commentary, Reston, VA.
ASTM. (2009). “Standard test methods for tension testing of metallic materials.” ASTM E8/E8M, West Conshohocken, PA.
Basler, K. (1960). “Web buckling tests on welded plate girders.”, Lehigh Univ. Libraries, Bethlehem, PA.
Basler, K. (1961). “Strength of plate girders in shear.” J. Struct. Div., 87(ST7), 151–180.
Basler, K. (1963). “Discussion of K. Basler ‘Strength of plate girders in shear.’” Trans. Am. Soc. Civ. Eng., 128(2), 712–719.
Carskaddan, P. S. (1968). “Shear buckling of unstiffened hybrid beams.” J. Struct. Div., 94(ST8), 1965–1992.
CEN (European Committee for Standardization). (2006). “Eurocode 3: Design of steel structures—Part 1–5: Plated structural elements.” EN 1993-1-5, Brussels, Belgium.
Daley, A., and Davis, B. (2015). “Shear strength of prismatic steel I-shaped members.”, Metal Building Manufacturers Association, Cleveland.
Frey, F., and Anslijn, R. (1977). “Shear tests on unstiffened plate girders.” Proc., 2nd Int. Colloquium, Stability of Steel Structures, Preliminary Rep., European Convention for Constructional Steelwork (ECCS), Brussels, Belgium, 321–326.
Gaylord, E. H. (1963). “Discussion of K. Basler ‘Strength of plate girders in shear.” Trans. Am. Soc. Civ. Eng., 128(2), 712–719.
Höglund, T. (1971). “Behaviour and strength of the web of thin plate I-girders.”, Royal Institute of Technology, Stockholm, Sweden.
Höglund, T. (1973). “Design of thin plate I-girders in shear and bending, with special reference to web buckling.”, Royal Institute of Technology, Stockholm, Sweden.
Höglund, T. (1997). “Shear buckling resistance of steel and aluminum plate girders.” Thin Walled Struct., 29(1–4), 13–30.
Lee, S. C., Davidson, J. S., and Yoo, C. H. (1996). “Shear buckling coefficients of plate girder web panels.” J. Comput. Struct., 59(5), 789–795.
Lee, S. C., Lee, D. S., and Yoo, C. H. (2008). “Ultimate shear strength of long web panels.” J. Constr. Steel Res., 64(12), 1357–1365.
Lee, S. C., and Yoo, C. H. (1998). “Strength of plate girder web panels under pure shear.” J. Struct. Eng., 184–194.
Lee, S. C., and Yoo, C. H. (1999). “Experimental study on ultimate shear strength of web panels.” J. Struct. Eng., 838–846.
Ravinger, J. (1983). “Girders with unstiffened slender webs.” J. Constr. Steel Res., 3(2), 14–22.
Vincent, G. S. (1969). “Tentative criteria for load factor design of steel highway bridges.”, American Iron and Steel Institute, Washington, DC.
White, D. W. (2008). “Unified flexural resistance equations for stability design of steel I-section members: Overview.” J. Struct. Eng., 1450–1470.
White, D. W., and Barker, M. G. (2008). “Shear resistance of transversely stiffened steel I-girders.” J. Struct. Eng., 1425–1436.
Yoo, C. H., and Lee, S. C. (2006). “Mechanics of web panel post-buckling behavior in shear.” J. Struct. Eng., 1580–1589.
Ziemian, R. D. (2010). Guide to stability design criteria for metal structures, 6th Ed., Wiley, Hoboken, NJ.
Information & Authors
Information
Published In
Copyright
©2016 American Society of Civil Engineers.
History
Received: Aug 31, 2015
Accepted: Jul 13, 2016
Published online: Oct 14, 2016
Published in print: Mar 1, 2017
Discussion open until: Mar 14, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.