Experimental Studies of Lipped Channel Beams Subject to Web Crippling under Two-Flange Load Cases
Publication: Journal of Structural Engineering
Volume 142, Issue 9
Abstract
Lipped channel beams (LCBs) are commonly used as flexural members such as floor joists and bearers in the construction industry. These thin-walled LCBs are subjected to specific buckling and failure modes, one of them being web crippling. Despite considerable research in this area, some recent studies have shown that the current web crippling design rules are unable to predict the test capacities under end-two-flange (ETF) and interior-two-flange (ITF) load conditions. In many instances, web crippling predictions by the available design standards such as AISI S100, AS/NZS 4600 and Eurocode 3 Part 1-3 are inconsistent, i.e., unconservative in some cases, although they are conservative in other cases. Hence, experimental studies consisting of 36 tests were conducted in this research to assess the web crippling behavior and capacities of high-strength LCBs under two-flange load cases (ETF and ITF). Experimental results were then compared with the predictions from current design rules. Comparison of the ultimate web crippling capacities from tests showed that the design equations are very unconservative for LCB sections under the ETF load case and are conservative for the ITF load case. Hence, improved equations were proposed to determine the web crippling capacities of LCBs based on the experimental results from this study. Current design equations do not provide the direct strength method (DSM) provisions for web crippling. Hence, suitable design rules were also developed under the DSM format using the test results and buckling analyses using finite-element analyses.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to thank Australian Research Council for their financial support and the Queensland University of Technology for providing the necessary facilities and support to conduct this research project.
References
ABAQUS [Computer software]. Dassault Systèmes, Waltham, MA.
AISI (American Iron and Steel Institute). (2008). “Standard test method for determining the web crippling strength of cold-formed steel beams.” AISI S909, Washington, DC.
AISI (American Iron and Steel Institute). (2012). “Specifications for the cold-formed steel structural members, cold-formed steel design manual.” AISI S100, Washington, DC.
Beshara, B., and Schuster, R. M. (2000). “Web crippling of cold formed steel C- and Z- sections.” 15th Int. Specialty Conf. on Cold-Formed Steel Structures, Department of Civil Engineering Center for Cold-Formed Steel Structures, Univ. of Missouri, Rolla, MO.
CEN (European Committee for Standardization). (2006). “Eurocode 3: Design of steel structures—Part 1-3: General rules—Supplementary rules for cold-formed members and sheeting.” EN 1993-1-3, Brussels, Belgium.
Choy, M. Y., Jia, X. F., Yuan, X., Zhou, J., Wang, H. S., and Yu, C. (2014). “Direct strength method for web crippling of cold-formed steel C- and Z- sections subjected to two-flange loading.” Proc., Annual Stability Conf. Structural Stability Research Council, Toronto, 99–111.
Duarte, A. P. C., and Silvestre, N. (2014). “A new slenderness-based approach for the web crippling design of plain channel steel beams.” Int. J. Steel Struct., 13(3), 421–434.
Gerges, R. R., and Schuster, R. M. (1998). “Web crippling of single web cold-formed steel members subjected to end one flange loading.” 14th Int. Specialty Conf. on Cold-Formed Steel Structures, Dept. of Civil Engineering Center for Cold-Formed Steel Structures, Univ. of Missouri, Rolla, MO.
Hancock, G. J., and Pham, C. H. (2015). “Buckling analysis of thin-walled sections under localised loading using the semi-analytical finite strip method.” Thin-Walled Struct., 86, 35–46.
Heiyantuduwa, M. (2008). “Web crippling behaviour of cold-formed thin walled steel lipped channel beams.” Ph.D. thesis, Glasgow Caledonian Univ., Lanarkshire, U.K.
Keerthan, P., and Mahendran, M. (2014). “Experimental study of web crippling behaviour of hollow flange channel beams under two flange load cases.” Thin-Walled Struct., 85, 207–219.
Macdonald, M., and Heiyantuduwa, M. A. (2012). “A design rule for web crippling of cold-formed steel lipped channel beams based on nonlinear FEA.” Thin-Walled Struct., 53, 123–130.
Macdonald, M., Heiyantuduwa, M. A., Kotelko, M., and Rhodes, J. (2011). “Web crippling behavior of thin-walled lipped channel beams.” Thin-Walled Struct., 49(5), 682–690.
Natário, P. (2015). “Localized failure of thin-walled steel members subjected to concentrated loads: Analysis, behaviour and design.” Ph.D. thesis, Instituto Superior Técnico, Universidade de Lisboa, Portugal.
Natário, P., Silvestre, N., and Camotim, D. (2016). “Direct strength prediction of web crippling failure of beams under ETF loading.” Thin-Walled Struct., 98, 360–374.
Prabakaran, K. (1993). “Web crippling of cold-formed steel sections.”, Dept. of Civil Engineering, Univ. of Waterloo, ON, Canada.
Prabakaran, K., and Schuster, R. M. (1998). “Web crippling of cold-formed steel sections.” 14th Int. Specialty Conf. on Cold-Formed Steel Structures, Dept. of Civil Engineering Center for Cold-Formed Steel Structures, Univ. of Missouri, Rolla, MO.
SA (Standards Australia/Standards New Zealand). (2005). “Australia/New Zealand standard AS/NZS 4600 cold-formed steel structures.” Sydney, Australia.
Schafer, B. W. (2008). “Review: The direct strength method of cold-formed steel member design.” J. Constr. Steel Res., 64(7–8), 766–778.
Timoshenko, S. P., and Gere, G. M. (1961). Theory of elastic stability, 2nd Ed., McGraw-Hill, New York.
Uzzaman, A., Lim, J. B. P., Nash, D., Rhodes, J., and Young, B. (2012a). “Cold-formed steel sections with web openings subjected to web crippling under two-flange loading conditions—Part I: Tests and finite element analysis.” Thin-Walled Struct., 56, 38–48.
Uzzaman, A., Lim, J. B. P., Nash, D., Rhodes, J., and Young, B. (2012b). “Cold-formed steel sections with web openings subjected to web crippling under two-flange loading conditions—Part II: Parametric study and proposed design equations.” Thin-Walled Struct., 56, 79–87.
Uzzaman, A., Lim, J. B. P., Nash, D., Rhodes, J., and Young, B. (2012c). “Web crippling behaviour of cold-formed steel channel sections with offset web holes subjected to interior-two-flange loading.” Thin-Walled Struct., 50(1), 76–86.
Uzzaman, A., Lim, J. B. P., Nash, D., Rhodes, J., and Young, B. (2013). “Effect of offset web holes on web crippling strength of cold-formed steel channel sections under end-two-flange loading condition.” Thin-Walled Struct., 65, 34–48.
Walker, A. C. (1975). Design and analysis of cold-formed sections, Wiley, New York.
Young, B., and Hancock, G. J. (2001). “Design of cold-formed channels subjected to web crippling.” J. Struct. Eng., 1137–1144.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Jul 14, 2015
Accepted: Feb 1, 2016
Published online: Apr 11, 2016
Published in print: Sep 1, 2016
Discussion open until: Sep 11, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.