Experimental and Numerical Study of Postbuckling Ductile Fracture of Heat-Treated SHS Stub Columns
Publication: Journal of Structural Engineering
Volume 140, Issue 7
Abstract
Previous studies have proposed a cyclic ductile fracture model by applying the void growth model and an established rule in incremental form, in which only a monotonic tensile coupon test is required to calibrate the parameters of the fracture model and the corresponding plasticity models. The model parameters were deduced from small-scale hourglass steel coupons, but not from large-scale specimens. In practice, however, ductile fracture after the occurrence of local buckling has been observed in steel members during recent huge earthquakes. This paper aims to establish a simulation method for the postbuckling cracking process on the basis of formerly proposed fracture and plasticity models. Experimental results demonstrate that the ultimate behaviors of heat-treated square hollow section (SHS) stub columns associated with plate buckling and ductile fracture under cyclic loading can be simulated with favorable accuracy.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research reported herein was sponsored by the Ministry of Education under the Grant-in-Aid for Scientific Research (A) No. 23246097 with the title “Study on the coupling of buckling and fracture of steel structural members.” This financial support is sincerely acknowledged. The experimental support by Prof. Iyama and Mr. Araki are greatly appreciated.
References
ABAQUS version 6.10 [Computer software]. Hibbitt, Karlsson & Sorensen, Pawtucket, RI.
Architectural Institute of Japan (AIJ). (1995). Fracture in steel structures during a severe earthquake, Tokyo (in Japanese).
Bai, Y. L., Bao, Y. B., and Wierzbicki, T. (2006). “Fracture of prismatic aluminum tubes under reverse straining.” Int. J. Impact Eng., 32(5), 671–701.
Bao, Y. B., and Wierzbicki, T. (2005). “On the cut-off value of negative triaxiality for fracture.” Eng. Fract. Mech., 72(7), 1049–1069.
Belytschko, T., Gracie, R., and Ventura, G. (2009). “A review of extended/generalized finite element methods for material modeling.” Modell. Simul. Mater. Sci. Eng., 17(4), 1–24.
Besson, J., Steglich, D., and Brocks, W. (2001). “Modeling of crack growth in round bars and plane strain specimens.” Int. J. Solids Struct., 38(46–47), 8259–8284.
Chaboche, J. L. (1986). “Time-independent constitutive theories for cyclic plasticity.” Int. J. Plast., 2(2), 149–188.
Chaboche, J. L. (1988). “Continuum damage mechanics: Part I—General concepts.” J. Appl. Mech., 55(1), 59–64.
Chaboche, J. L., Dang Van, K., and Cordier, G. (1979). “Modelization of the strain memory effect on the cyclic hardening of 316 stainless steel.” SMiRT-5, North-Holland Publishing, Berlin.
Chi, W. M., Kanvinde, A. M., and Deierlein, G. G. (2006). “Prediction of ductile fracture in steel connections using SMCS criterion.” J. Struct. Eng., 171–181.
Fell, V., Kanvinde, A. M., and Deierlein, G. G. (2009). “Experimental investigation of inelastic cyclic buckling and fracture of steel braces.” J. Struct. Eng., 19–32.
Goggins, J. M., Broderick, B. M., Elghazouli, A. Y., and Lucas, A. S. (2005). “Experimental cyclic response of cold-formed hollow steel bracings.” Eng. Struct., 27(7), 977–989.
Goggins, J. M., Broderick, B. M., Elghazouli, A. Y., and Lucas, A. S. (2006). “Behaviour of tubular steel members under cyclic axial loading.” J. Constr. Steel Res., 62(1–2), 121–131.
Hancock, J. W., and Cowling, M. J. (1980). “Role of state of stress in crack-tip failure processes.” Met. Sci., 14(8–9), 293–304.
Jia, L. J. (2013). “Ductile fracture of structural steels under cyclic large strain loading.” Doctoral dissertation, University of Tokyo, Tokyo.
Jia, L. J., and Kuwamura, H. (2013). “Ductile fracture simulation of structural steels under monotonic tension.” J. Struct. Eng., 04013115.
Jia, L. J., and Kuwamura, H. (2014). “Prediction of cyclic behaviors of mild steel at large plastic strain using coupon test results.” J. Struct. Eng., 04013056.
Jiao, H., and Zhao, X. L. (2001). “Material ductility of very high strength (VHS) circular steel tubes in tension.” Thin-walled Struct., 39(11), 887–906.
Jiao, Y., Yamada, S., Kishiki, S., and Shimada, Y. (2011). “Evaluation of plastic energy dissipation capacity of steel beams suffering ductile fracture under various loading histories.” Earthquake Eng. Struct. Dyn., 40(14), 1553–1570.
Kanvinde, A. M., and Deierlein, G. G. (2006). “Void growth model and stress modified critical strain model to predict ductile fracture in structural steels.” J. Struct. Eng., 1907–1918.
Kanvinde, A. M., and Deierlein, G. G. (2007). “Cyclic void growth model to assess ductile fracture initiation in structural steels due to ultra low cycle fatigue.” J. Eng. Mech., 701–712.
Kumar, S., and Usami, T. (1996). “Damage evaluation in steel box columns by cyclic loading tests.” J. Struct. Eng., 626–634.
Kuwamura, H. (1997). “Transition between fatigue and ductile fracture in steel.” J. Struct. Eng., 864–870.
Kuwamura, H., and Akiyama, H. (1994). “Brittle fracture under repeated high stresses.” J. Constr. Steel Res., 29(1–3), 5–19.
Kuwamura, H., and Yamamoto, K. (1997). “Ductile crack as trigger of brittle fracture in steel.” J. Struct. Eng., 729–735.
Kuwamura Lab. (1995). Field survey report on structural damage during the 1995 Hyogoken-Nanbu Earthquake, School of Engineering, University of Tokyo (in Japanese).
Mackenzie, A. C., Hancock, J. W., and Brown, D. K. (1977). “On the influence of state of stress on ductile failure initiation in high strength steels.” Eng. Fract. Mech., 9(1), 167–188.
Mahin, S. A. (1998). “Lessons from damage to steel buildings during Northridge earthquake.” Eng. Struct., 20(4–6), 261–270.
Miner, M. A. (1945). “Cumulative damage in fatigue.” J. Appl. Mech., 12(3), A159–A164.
Myers, A., Kanvinde, A. M., and Deierlein, G. G. (2009). “Testing and probabilistic simulation of ductile fracture initiation in structural steel components and weldments.” Blume Center TR170, Stanford University. Stanford, CA, 〈http://blume.stanford.edu〉 (Feb. 3, 2013).
Ohata, M., and Toyoda, M. (2004). “Damage concept for evaluating ductile cracking of steel structure subjected to large-scale cyclic straining.” Sci. Technol. Adv. Mater., 5(1–2), 241–249.
Panontin, T. L., and Sheppard, S. D. (1995). “The relationship between constraint and ductile fracture initiation as defined by micromechanical analyses.” Fracture mechanics: 26th Vol., ASTM STP 1256, ASTM, West Conshohocken, PA, 54–85.
Rousselier, G. (1987). “Ductile fracture models and their potential in local approach of fracture.” Nucl. Eng. Des., 105(1), 97–111.
Toyoda, M., Ohata, M., Ayukawa, N., Ohwaki, G., Ueda, Y., and Takeuchi, I. (2000). “Ductile fracture initiation behavior of pipe under a large scale of cyclic bending.” Proc., 3rd Int. Pipeline Technology Conf., Vol. II, Elsevier Science B.V., Amsterdam, The Netherlands, 87–102.
Yasuda, O., Hirono, M., Terai, M., Ohata, M., and Toyoda, M. (2004). “Application to ductile cracking evaluation for beam-to-column connection of steel pier—Evaluation of ductile crack initiation for welded structures subjected to large scale cyclic loading (Report 2).” Q. J. Jpn. Weld. Soc., 22(3), 467–476 (in Japanese).
Zaverl, J. R., and Lee, D. (1978). “Constitutive relations for nuclear reactor core materials.” J. Nucl. Mater., 75(1), 14–19.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Oct 14, 2013
Accepted: Feb 20, 2014
Published online: Apr 3, 2014
Published in print: Jul 1, 2014
Discussion open until: Sep 3, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.