Analytical Evaluation of FRP Wrapping Effectiveness in Restraining Reinforcement Bar Buckling
Publication: Journal of Structural Engineering
Volume 140, Issue 7
Abstract
Internal transverse steel reinforcements (e.g., stirrups) are the main internal devices that prevent the longitudinal steel bar buckling, but in many existing reinforced concrete (RC) structures the amount and the spacing between steel stirrups are inadequate. In these structures, longitudinal bar buckling can be prevented by applying external reinforcement, in particular, by means of fiber-reinforced polymer (FRP) wrapping. A novel analytical approach for the study of longitudinal bar buckling in columns wrapped with FRP is proposed. Longitudinal bars have been considered as axially loaded beams, whereas the mechanical effect of FRP wrapping on the bars has been modeled by means of springs. The effect of elastic and inelastic behavior has been taken into account by means of the reduced modulus theory. The well-known relations for steel stirrups have been revisited in the case of FRP wrapping to propose an analytical formulation, valid both for circular and noncircular cross sections of columns, for the evaluation of the FRP thickness needed to prevent the longitudinal bar buckling.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The analyses were developed within the activities of Rete dei Laboratori Universitari di Ingegneria Sismica—ReLUIS for the research program funded by the Dipartimento di Protezione Civile—Progetto Esecutivo 2010–2013.
References
American Concrete Institute (ACI). (2011). “Building code requirements for structural concrete and commentary.”, Detroit, 503.
Chajes, A. (1974). Principles of structural stability theory, Prentice Hall, Upper Saddle River, NJ.
Consiglio Nazionale Delle Ricerche (CNR). (2012). “Guide for the design and construction of externally bonded FRP systems for strengthening existing structures guidelines.”, Rome, Italy.
Cosenza, E., and Prota, A. (2006). “Experimental behaviour and numerical modelling of smooth steel bars under compression.” J. Earthquake Eng. 10(3), 313–329.
Dei Poli, S., Di Prisco, M., and Gambarovam, P. G. (1988). “Dowel action as a means of shear transmission in RC elements: A state of art and new test result.” Studi e Ricerche, School for the design of R/C Structures, Milan Univ. of Technology, 9(87), 217–303 (in Italian).
European Committee for Standardization (CEN). (2004a). “Design of concrete structures. Part 1-1: General rules and rules for buildings.” Eurocode 2, Brussels, Belgium.
European Committee for Standardization (CEN). (2004b). “Design of structures for earthquake resistance. Part 1: General rules, seismic actions and rules for buildings.” Eurocode 8, Brussels, Belgium.
Jimenez-Perez, R., White, R. N., and Gergely, P. (1979). “Bond and dowel capacities of reinforced concrete.” ACI J. Proc., 76(1), 73–92.
Lignola, G. P., Prota, A., Manfredi, G., and Cosenza, E. (2009). “Non linear modeling of RC hollow piers confined with CFRP.” Compos. Struct., 88(1), 56–64.
Lignola, G. P., Prota, A., Manfredi, G., and Cosenza, E. (2012). “Multiscale non linear analysis of RC hollow piers wrapped with CFRP under shear-type load.” Construct. Build. Mater., 35, 947–959.
Papia, M., Russo, G., and Zingone, G. (1988). “Instability of longitudinal bars in R.C. columns.” J. Struct. Eng., 445–461.
Pellegrino, C., and Modena, C. (2010). “Analytical model for FRP confinement of concrete columns with and without internal steel reinforcement.” J. Comp. Construct., 693–705.
Priestley, M. J. N., Seible, F., and Calvi, G. M. (1996). Retrofit design, in seismic design and retrofit of bridges, Wiley, Hoboken, NJ.
Ramberg, W., and Osgood, W. R. (1943). “Description of stress-strain curves by three parameters.” Technical Note No. 902, National Advisory Committee for Aeronautics, Washington, DC.
Rousakis, T. C., and Karabinis, A. I. (2012). “Adequately FRP confined reinforced concrete columns under axial compressive monotonic or cyclic loading.” Mater. Struct., 45(7), 957–975.
Sakai, K., and Sheikh, S. A. (1989). “What do we know about confinement in reinforced concrete columns? (A critical review of previous work and code provisions).” ACI Struct. J., 86(2), 192–207.
Shanley, F. R. (1947). “Inelastic column theory.” J. Aeronaut. Sci., 14(5), 261–268.
Soroushian, P., Obaseki, K., and Rojas, M. C. (1987). “Bearing strength and stiffness of concrete under reinforcing bars.” ACI Mater. J., 84(3), 179–184.
Tastani, S. P., Pantazopoulou, S. J., Zdoumba, D., Plakantaras, V., and Akritidis, E. (2006). “Limitations of FRP jacketing in confining old-type reinforced concrete members in axial compression.” J. Comp. Construct., 13–25.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Mar 15, 2013
Accepted: Oct 25, 2013
Published online: Apr 3, 2014
Published in print: Jul 1, 2014
Discussion open until: Sep 3, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.