State-of-the-Art Review of Approaches for the Design of Timber Beams with Notches
Publication: Journal of Structural Engineering
Volume 140, Issue 3
Abstract
Notches are details that significantly reduce the load-carrying capacity of beams made of timber. The amount of reduction was the subject of investigation in numerous studies from an experimental or theoretical point of view. The singular stress distribution around the notch corner can be described by equations based on linear elastic fracture mechanics, fracture energy, or complex solutions. From experimental tests, simplified equations can be proposed. Standards, codes, and handbooks for the design of timber structures are based on such equations. When comparing the dimensions of notched beams tested in experiments with those that are relevant in practical applications, specimens of small dimensions were primarily tested. The application of design approaches verified by tests on specimens of small dimensions and the use of material properties determined from small clear specimens do not account for size effects that are important when working with beams of large dimensions. The influence of duration of load, moisture variation, and cyclic loading on the fracture of the notch has to be studied. An extension of tests on notched beams and relevant material properties that are now gained from small clear specimens to those of large dimensions is necessary.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This state-of-the-art review is part of the “Structural behaviour of glued laminated timber” project (project number 200021–126655), funded by the Swiss National Science Foundation SNSF, which is gratefully acknowledged.
References
Aicher, S. (1994). “Bruchenergien, kritische Energiefreisetzungsraten und Bruchzähigkeiten von Fichte bei Zugbeanspruchung senkrecht zur Faserrichtung.” Holz als Roh- und Werkstoff, 52(6), 361–370.
American Institute of Timber Construction. (2005). Timber construction manual, Wiley, New York.
American Wood Council. (2006). National design specifications (NDS) for wood construction commentary, 2005 edition, American Forest & Paper Association, Washington DC.
Angst, V., and Malo, K. A. (2012). “The effect of climate variations on glulam—an experimental study.” Eur. J. Wood Wood Prod., 70(5), 603–613.
APA—The Engineered Wood Assoc. (2006). Field notching and drilling of glued laminated timber beams, APA, Tacoma, WA.
Ashby, M. F., Easterling, K. E., Harrysson, R., and Maiti, S. K. (1984). “Fracture and toughness of woods.”, Cambridge Univ. Engineering Dept., Cambridge, UK.
Asiz, A., and Smith, I. (2008). “Design of inclined glulam members with an end notch on the tension face.” Paper CIB-W18/41-6-1Proc., Meeting 41 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Canadian Institute of Timber Construction. (1963). Timber construction. Canadian Institute of Timber Construction, Ottawa, Canada.
Canadian Standards Assoc. (CSA). (2009). O86-09: Engineering design of wood, CSA, Mississauga, Canada.
Ehlbeck, J., and Kürth, J. (1992). Bewertung eines neuen Bemessungskonzeptes für ausgeklinkte Träger auf der Grundlage der Bruchmechanik. Versuchsanstalt für Stahl, Holz und Steine, Abteilung Ingenieurholzbau, Universität Fridericiana Karlsruhe, Karlsruhe, Germany.
European Committee for Standardization (CEN). (2004). EN 1995-1-1: Eurocode 5: Design of timber structures—Part 1-1: General—Common rules and rules for buildings, CEN, Bruxelles, Belgium.
Foliente, G. C., and McLain, T. E. (1992a). “Design of notched wood beams.” J. Struct. Eng., 2407–2420.
Foliente, G. C., and McLain, T. E. (1992b). “Strength of end-notched wood beams: A critcal fillet hoop stress approach.” Wood Fiber Sci., 24(2), 168–180.
Foliente, G. C., McLain, T. E., and Pneuman, F. C. (1992). “Draft design criteria for notched wood beams.” Wood Design Focus, 3(4), 3–8.
Fonselius, M. (1993). “Long-term experiments with end-cracked wooden beams.” Wood Sci. Tech., 27(2), 137–150.
Forest Products Laboratory. (1987). Wood handbook: Wood as an engineering material, U.S. Dept. of Agriculture, Forest Service, Forest Products Laboratory, Madison, WI.
Fortino, S., Mirianon, F., and Toratti, T. (2009). “A 3D moisture-stress FEM analysis for time dependent problems in timber structures.” Mech. Time-Dependent Mater., 13(4), 333–356.
Foschi, R. O., and Barrett, J. D. (1980). “Consideration of size effects in longitudinal shear strength for uncracked beams.” Paper No. CIB-W18/13-6-2., Proc., Meeting 13 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Franke, B. (2008). “Zur Bewertung der Tragfähigkeit von Trägerausklinkungen in Nadelholz” Doctoral thesis, Bauhaus-Universität, Weimar, Germany.
Gerhardt, T. D. (1984). Strength and stiffness analysis of notched green oak pallet stringers, U.S, Dept. of Agriculture, Forest Service, Forest Products Laboratory, Madison. WI.
Gustafsson, P. J. (1988). “A study of strength of notched beams.” Paper No. CIB-W18/21-10-1, Proc., Meeting 21 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Gustafsson, P. J., Hoffmeyer, P., and Valentin, G. (1998). “DOL behaviour of end-notched beams.” Holz als Roh-und Werkstoff, 56(5), 307–317.
Henrici, D. (1984). “Beitrag zur Spannungsermittlung in ausgeklinkten Biegeträgern aus Holz.” Doctoral thesis, Technische Universität München, Munich, Germany.
Hinkes, F.-J. (1988). “Experimentelle und rechnerische Untersuchungen zur Ermittlung der Tragfähigkeit von Zapfenverbindungen.” Fortschrittsberichte VDI, Reihe 4: Bauingenieurwesen, VDI Verlag, Düsseldorf, Germany.
Hunt, D. G., and Croager, W. P. (1982). “Mode II fracture toughness of wood measured by a mixed-mode test method.” J. Mater. Sci. Lett., 1(2), 77–79.
Hunt, D. G., and Rukhadze, M. (1991). “Mixed-mode- fracture of beams with notched ends.” Proc., Int. Timber Eng. Conf., London.
Irwin, G. R. (1957). “Analysis of stresses and strains near the end of a crack traversing a plate.” J. Appl. Mech., 24, 361–364.
Jockwer, R., Steiger, R., Frangi, A., and Köhler, J. (2011). “Impact of material properties on the fracture mechanics design approach for notched beams in Eurocode 5.” Paper No. CIB-W18/44-6-1, Proc., Meeting 44 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Larsen, H. J., and Gustafsson, P. J. (1990). “The fracture energy of wood in tension perpendicular to the grain.” Paper No. CIB-W18/23-19-2, Proc., Meeting 23 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Larsen, H. J., Riberholt, H., and Gustafsson, P. J. (1992). “Annex to paper CIB-W18/25-102-1—Eurocode 5 - Design of notched beams.” Paper No. CIB-W18/25-102-1AProc., Meeting 25 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Leicester, R. H. (1969). “The size effect of notches.” Proc., 2nd Australasian Conf. on Mech. of Struct. and Mater., Vol. 4, 1–20.
Leicester, R. H. (1971). “Some aspects of stress fields at sharp notches in orthotropic material.” Division of Forest Products Technological Paper No. 57, Commonwealth Scientific and Industrial Research Organization, Melbourne, Australia.
Leicester, R. H. (1973). “Effect of size on the strength of structures.” Division of Building Research Technological Paper no. 71, Commonwealth Scientific and Industrial Research Organization, Melbourne, Australia.
Leicester, R. H. (2005). “Design specifications for notched beams in AS 1720.” Paper No. CIB-W18/38-6-1Proc., Meeting 38 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Leicester, R. H. (2006). “Application of linear fracture mechanics to notched timber elements.” Progress Struct. Eng. Mater., 8(1), 29–37.
Logemann, M. (1991). “Abschätzung der Tragfähigkeit von Bauteilen mit Ausklinkungen oder Durchbrüchen.” Fortschrittsberichte VDI, Reihe 4: Bauingenieurwesen, VDI Verlag, Düsseldorf, Germany.
Lum, C., and Foschi, R. O. (1988). “Arbitrary V-notches in orthotropic plates.” J. Eng. Mech., 114(4), 638–655.
Mall, S., Murphy, J. F., and Shottafer, J. E. (1983). “Criterion for mixed mode fracture in wood.” J. Eng. Mech., 680–690.
Masuda, M. (1996). “Application of the finite small area fracture criteria to bending of beams with end sloped notches.” Proc., Int. Wood Engineering Conf., Vol. 4, 136–143.
Mistler, H.-L. (1979). “Die Tragfähigkeit des am Endauflager unten rechtwinklig ausgeklinkten Brettschichtträgers.” Doctoral thesis, Technische Hochschule Karlsruhe, Karlsruhe, Germany.
Möhler, K., and Mistler, H.-L. (1978). Untersuchungen über den Einfluss von Ausklinkungen im Auflagerbereich von Holzbiegeträgern auf die Tragfestigkeit, Fraunhofer IRB Verlag.
Morlier, P., and Ranta-Maunus, A. (1998). “DOL effect of different sized timber beams.” Holz als Roh-und Werkstoff, 56(5), 279–284.
Murphy, J. F. (1979). “Using fracture mechanics to predict failure in notched wood beams.” Proc., 1st Int. Conf. on Wood Fracture, Forintek Canada Corp., Western Forest Products Laboratory, Vancouver, BC, 159–173.
Murphy, J. F. (1986). “Strength and stiffness reduction of large notched beams.” J. Struct. Eng., 1989–2000.
Petersson, H. (1992). “On design criteria for tension perpendicular to grain.” Paper No. CIB-W18/25-6-4Proc., Meeting 25 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Rammer, D. R. (2010). “Structural analysis equations.” Chapter 9, Wood handbook: Wood as an engineering material, R. J. Ross, ed., U.S. Dept. of Agriculture, Forest Service, Forest Products Laboratory, Madison, WI, 9-1–9-11.
Rautenstrauch, K., Franke, B., Franke, S., and Schober, K. U. (2008a). “A new design approach for end-notched beams: View in code.” Paper No. CIB-W18/41-6-2, Proc., Meeting 41 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Rautenstrauch, K., Schwarz, W., Franke, S., Franke, B., Seyler, S., and Fichtmüller, D. (2008b). Beanspruchungsanalyse von Bauteilen aus Voll- und Brettschichtholz durch Industriephotogrammetrie am Beispiel von Ausklinkungen und Durchbrüchen. Schlussbericht, Fraunhofer IRB Verlag, Stuttgart, Germany.
Riberholt, H., Enquist, B., Gustafsson, P. J., and Jensen, R. B. (1991). Timber beams notched at the support, Afdelingen for Baerende Konstruktioner, Lyngby, Denmark.
Riipola, K. (1990). “Dimensioning of beams with cracks, notches and holes. An application of fracture mechanics.” Paper No. CIB-W18/23-10-2, Proc., Meeting 23 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Rug, W., Badstube, M., and Schöne, W. (1990). “Determination of the fracture energy of wood for tension perpendicular to the grain.” Paper No. CIB-W18/23-19-1Proc., Meeting 23 of the Working Commission W18-Timber Structures, CIB, International Council for Research and Innovation in Building and Construction, Rotterdam, The Netherlands.
Schelling, W., and Hinkes, F.-J. (1985). Tragverhalten von Zapfenverbindungen Untersuchungen, Institut für Bautechnik und Holzbau Hannover, IRB-Verlag, Stuttgart, Germany.
Scholten, J. A. (1935). “Rounding notches makes stronger joists.” Pacific Logging Congress, Vol. 46, American Lumberman, Chicago, IL.
Sih, G. C., Paris, P. C., and Irwin, G. R. (1965). “On cracks in rectilinearly anisotropic bodies.” Int. J. Fracture Mech., 1(3), 189–203.
Smith, I., and Chui, Y. H. (1994). “Factors affecting mode I fracture energy of plantation-grown red pine.” Wood Sci. Technol., 28(2), 147–157.
Smith, I., Chui, Y. H., and Hu, L. J. (1996a). “Reliability analysis for critical reaction forces of lumber members with an end notch.” Can. J. Civil Eng., 23(1), 202–210.
Smith, I., Landis, E., and Gong, M. (2003). Fracture and fatigue in wood, Wiley, Chichester.
Smith, I., and Springer, G. (1993). “Consideration of Gustaffsson’s proposed Eurocode 5 failure criterion for notched timber beams.” Can. J. Civil Eng., 20(6), 1030–1036.
Smith, I., Tan, D., and Chui, Y. H. (1996b). “Critical reaction forces for notched timber members.” Proc., Int. Wood Engineering Conf., Louisiana State Univ., Baton Rouge, LA, 3460–3471.
Smith, I., and Vasic, S. (2003). “Fracture behaviour of softwood.” Mech. Mater., 35(8), 803–815.
Standards Association of Australia. (1972). AS CA65-1972, SAA Timber Engineering Code, Standards Association of Australia, Sydney, Australia, 125 p.
Standards Australia International. (1997). Australian Standard—Timber Structures—Part 1: Design methods, Standards Australia International, Sydney, 181 p.
Stieda, C. K. A. (1966). “Stress concentration around holes and notches and their effect on the strength of wood beams.” J. Mater., 1(3), 560–581.
Swiss Society of Engineers, and Architects. (2012). Standard SIA 265-Timber Structures, Swiss Society of Engineers and Architects, Zurich, Switzerland.
Timber Frame Engineering Council (TFEC). (2007). Standard for Design of Timber Frame Structures and Commentary, Timber Frame Engineering Council, Becket, MA.
Valentin, G., Racois, P., Morlier, P. (1994). “Experiments on the strength of notched beams.” Proc., Timber Engineering Meeting of the International Union of Forestry Research Organiza-tions (Iufro), 241–248.
Vasic, S., and Ceccotti, A. (2009). “Influence of intermediate deformation rates in softwoods characterized with fracture resistance R-curves.” Wood Sci. Technol., 43(7–8), 591–614.
Vasic, S., Ceccotti, A., Smith, I., and Sandak, J. (2009). “Deformation rates effects in softwoods: Crack dynamics with lattice fracture modelling.” Eng. Fracture Mech., 76(9), 1231–1246.
Vasic, S., and Stanzl-Tschegg, S. (2007). “Experimental and numerical investigation of wood fracture mechanisms at different humidity levels.” Holzforschung, 61(4), 367–374.
Walsh, P. F. (1972). “Linear fracture mechanics in orthotropic materials.” Eng. Fracture Mech., 4(3), 533–541.
Walsh, P. F. (1974). “Linear fracture mechanics solutions for zero and right angle notches.” Div. of Building Research Technological Paper No. 2, Commonwealth Scientific and Industrial Research Organization, Melbourne, Australia.
Walsh, P. F., Leicester, R. H., and Ryan, A. (1973). “The strength of glued lap joints in timber.” For. Prod. J., 23(5), 30–33.
Williams, M. L. (1952). “Stress singularities resulting from various boundary conditions in angular corners of plates in extension.” J. Appl. Mech., 19(4), 526–528.
Wood, L. W. (1951). “Relation of strength of wood to duration of load.”, USDA Forest Service, Forest Products Laboratory, Madison, WI.
Wu, E. M. (1967). “Application of fracture mechanics to anisotropic plates.” J. Appl. Mech., 34(4), 967–974.
Zalph, B. L., and McLain, T. E. (1988). “Bending strength of notched wood beams.” Proc., Int. Conf. on Timber Engineering, Forest Products Research Society, Madison, WI.
Zalph, B. L., and McLain, T. E. (1992). “Strength of wood beams with filleted interior notches: A new model.” Wood Fiber Sci., 24(2), 204–215.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 140 • Issue 3 • March 2014
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Aug 3, 2012
Accepted: Mar 8, 2013
Published online: Mar 11, 2013
Published in print: Mar 1, 2014
Discussion open until: Apr 6, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.