Development of an Axial Load Capacity Equation for Doubly Symmetric Built-Up Cold-Formed Sections
Publication: Journal of Structural Engineering
Volume 139, Issue 12
Abstract
This work aims to develop an axial load capacity equation for doubly symmetric built-up cold-formed sections with a sufficient number of intermediate, symmetrical connections. A numerical parametric study involving a total of 360 different configurations was conducted, and the numerical results were compared with the experimental data and specifications from the American Iron and Steel Institute (AISI). In this process, the axial load capacities and failure modes, which were influenced by out-of-straightness and out-of-flatness, were thoroughly investigated. To address the issues of an unnecessarily complicated AISI specification for doubly symmetric members subject to distortional buckling, a simple and reliable axial load capacity equation was developed based on a regression analysis of a three-dimensional surface fitting and calibration with the experimental data. This proposed equation exhibited good agreement with the numerically simulated and experimentally measured capacities, while simultaneously ensuring safety and efficiency.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The work presented in this paper was funded by the University of Oklahoma, Star Building Systems, and Engineering Research Institute and College of Engineering of Seoul National University. Also, this work was supported by the National Research Foundation of Korea (2012-005905). The views expressed are those of authors, and do not necessarily represent those of the sponsors.
References
ABAQUS [Computer software]. Dassault Systèmes, Paris.
AISC. (2005). Steel construction manual, 13th Ed., Chicago.
American Iron, and Steel Institute. (1986). Cold-formed steel design manual, Washington, DC.
American Iron, and Steel Institute. (1991). Cold-formed steel design manual, Washington, DC.
American Iron, and Steel Institute. (1996). Cold-formed steel design manual, Washington, DC.
American Iron, and Steel Institute. (2001). North American specification for the design of cold-formed steel structural members, Washington, DC.
American Iron, and Steel Institute. (2007). North American specification for the design of cold-formed steel structural members, Washington, DC.
ANSYS [Computer software]. Ansys, Inc., Canonsburg, PA.
Ashraf, M., Gardner, L., and Nethercot, D. (2005). “Strength enhancement of corners regions of stainless steel cross sections.” J. Constr. Steel Res., 61(1), 37–52.
Bakker, M. C. M., and Peköz, T. (2001). “The finite element method for thin-walled members—Basic principles.” 3rd Int. Conf. on Thin-Walled Structures, Elsevier, Oxford, UK, 427–436.
Becque, J., and Rasmussen, J. R. (2009). “Numerical investigation of the interaction of local and overall buckling of stainless steel I-columns.” J. Struct. Eng., 135(11), 1349–1356.
Biggs, K. A. (2008). “Axial load capacity of cold-formed, built-up members.” M.S. thesis, Univ. of Oklahoma, Norman, OK.
Bjørhovde, R. (1992). “Compression members.” Chapter 2.3, Constructional steel design—An international guide, P. J. Dowling, J. E. Harding, and R. Bjorhovde, eds., Elsevier Applied Science, Philadelphia.
Brueggen, B., and Ramseyer, C. (2003). “Cold-formed steel joist member buckling capacity testing.” Technical Rep., Donald G. Fears Structural Engineering Laboratory, Univ. of Oklahoma, Norman, OK.
Hancock, G., Murray, T., and Ellifritt, D. (2001). Cold-formed steel structures to the AISI specification, Marcel Dekker, New York, NY.
Harman, T., Dabney, J., and Richert, N. (2000). Advanced engineering mathematics with MATLAB, Brooks/Cole, Stamford, CT.
Madenci, E., and Guven, I. (2006). The finite element method and applications in engineering using ANSYS, Springer Science and Business Media, Heidelberg, Germany.
Mathews, J., and Fink, K. (2004). Numerical methods using MATLAB, Pearson Prentice Hall, Upper Saddle River, NJ.
Piyawat, K. (2011). “A suggested design approach for built-up cold-formed columns based on research using nonlinear finite element method.” Ph.D. thesis, Univ. of Oklahoma, Norman, OK.
Piyawat, K., Ramseyer, C., and Kang, T. H.-K. (2011). “Nonlinear buckling of built-up cold-formed sections.” Int. J. Theoret. Appl. Multiscale Mech., 2(2), 146–164.
Whittle, J. (2007). “Buckling capacities of axial loaded cold-formed built-up members.” M.S. thesis, Univ. of Oklahoma, Norman, OK.
Whittle, J., and Ramseyer, C. (2009). “Buckling capacities of axially loaded, cold-formed, built-up c-channels.” Thin Walled Struct., 47(2), 190–201.
Yang, D., and Hancock, G. (2004). “Compression tests of cold-reduced high strength steel sections. I: Stub columns.” J. Struct. Eng., 130(11), 1772–1781.
Yang, D., Hancock, G., and Rasmussen, K. (2004). “Compression tests of cold-reduced high strength steel sections. II: Long columns.” J. Struct. Eng., 130(11), 1782–1788.
Yu, W. W., and LaBoube, R. (2010). Cold-formed steel design, 4th Ed., Wiley, New York.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Mar 28, 2012
Accepted: Nov 28, 2012
Published online: Dec 1, 2012
Published in print: Dec 1, 2013
Discussion open until: Feb 5, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.