Simplified Procedure for Seismic Evaluation of Piles with Partial-Moment Connection to the Deck in Marine Oil Terminals
Publication: Journal of Structural Engineering
Volume 136, Issue 5
Abstract
This paper presents development of a simplified procedure for seismic evaluation of piles with partial-moment connection typically used in marine oil terminals. The current seismic evaluation procedure of the piles in marine oil terminals includes monitoring material strains specified in the Marine Oil Terminal Engineering and Maintenance Standard (MOTEMS) during the nonlinear static pushover analysis to estimate the displacement capacity of piles. This investigation developed closed-form formulas for estimating the displacement capacity of piles by using a simple pile-deck connection system. The displacement capacity estimated from these formulas ensures that the material stain limits specified in the MOTEMS is not exceeded. These formulas are demonstrated to be “accurate” by comparing results from these formulas against those from the nonlinear finite-element analysis. The formulas developed in this investigation utilize the curvature ductility capacity of the pile section and rotation ductility capacity of the connection at the selected seismic design level, along with the parameter which depends on the relative stiffness of the pile and the connection and the parameter which depends on the relative strength of the connection and the pile.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research investigation is supported by the California State Lands Commission (CSLC) under Contract No. UNSPECIFIEDC2005-051 with Martin Eskijian as the project manager. This support is gratefully acknowledged.
References
Chai, Y. H. (2002). “Flexural strength and ductility of extended pile-shafts. I: Analytical model.” J. Struct. Eng., 128(5), 586–594.
Chai, Y. H., and Hutchinson, T. C. (2002). “Flexural strength and ductility of extended pile-shafts. II: Experimental study.” J. Struct. Eng., 128(5), 595–602.
Eskijian, M. (2007). “Marine oil terminal engineering and maintenance standards (MOTEMS).” Proc., 2007 Structures Congress, ASCE, Reston, Va.
Ferritto, J., Deckenson, S., Priestley, N., Werner, S., and Taylor, C. (1999). “Seismic criteria for California marine oil terminals.” Technical Rep. No. TR-2103-SHR, Naval Facilities Engineering Service Center, Shore Facilities Dept., Structures Div., Port Hueneme, Calif.
Goel, R. K. (2008a). “Simplified procedure for seismic analysis of piles in marine oil terminals.” Proc., 2008 Structures Congress, ASCE, Reston, Va.
Goel, R. K. (2008b). “Simplified procedures for seismic analysis and design of piers and wharves in marine oil and LNG terminals.” Draft Rep. No. CP/SEAM-08/01, California Polytechnic State Univ., San Luis Obispo, Calif.
Klusmeyer, L., and Harn, R. (2004). “Displacement-based seismic design of large naval pier.” Proc., PORTS 2004, ASCE, Reston, Va.
Marine Oil Terminal Engineering and Maintenance Standards (MOTEMS). (2006). Marine Oil Terminal Engineering And Maintenance Standards, Chapter 31F, Title 24, Part 2, California State Lands Commission, Long Beach, Calif. ⟨http://www.slc.ca.gov/Division_pages/MFD/MOTEMS.html⟩ (April 28, 2006).
McKenna, F., and Fenves, G. (2001). The OpenSees command language manual: Version 1.2, Pacific Earthquake Engineering Center, Univ. of California, Berkeley, Calif., ⟨http://opensees.berkeley.edu⟩ (June 3, 2003).
Nezamian, A., Al-Mahaidi, R., and Grundy, P. (2006). “Bond strength of concrete plugs embedded in tubular steel piles under cyclic loading.” Can. J. Civ. Eng., 33(2), 111–125.
Park, R. J. T., Priestly, M. J. N., and Berrill, J. B. (1987). “Seismic performance of steel-encased concrete piles.” Rep. No. 87-5, Dept. of Civil Engineering, Univ. of Canterbury, New Zealand.
Priestley, M. J. N., and Park, R. (1984). “Strength and ductility of bridge substructures.” Rep. No. 84-20, Dept. of Civil Engineering, Univ. of Canterbury, New Zealand.
Priestley, M. J. N., Seible, F., and Calvi, G. M. (1996). Seismic design and retrofit of bridges, Wiley, New York.
Raynor, D. J., Lehman, D. E., and Stanton, J. F. (2002). “Bond-slip response of reinforcing bars grouted in ducts.” ACI Struct. J., 99(5), 568–576.
Restrepo, J. I., Yin, P., Jaradat, O., and Weismair, M. (2007). “Performance of new pile-deck connections under earthquakes.” Proc., 2007 Structures Congress, ASCE, Reston, Va.
Roeder, C. W., Graff, R., Sonderstrom, J., and Yoo, J. H. (2005). “Seismic performance of pile-wharf connections.” J. Struct. Eng., 131(3), 428–437.
Wray, M., Harn, R., and Jacob, J. (2007). “Port of Everett rail/barge transfer facility seismic design Everett, Washington.” Proc., PORTS 2007, ASCE, Reston, Va.
Information & Authors
Information
Published In
Copyright
© 2010 ASCE.
History
Received: May 27, 2008
Accepted: Nov 2, 2009
Published online: Nov 13, 2009
Published in print: May 2010
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.