Estimating Maximum Bending Moment in High-Density Polyethylene Pipes under Traffic Loading
Publication: Journal of Pipeline Systems Engineering and Practice
Volume 12, Issue 2
Abstract
High-density polyethylene (HDPE) pipes have been widely adopted for municipal pipeline projects all over the world. HDPE pipe failures, including reduced flow capacity and wall buckling, have been reported extensively, and traffic loading is one of the major causes. Understanding bending moments in HDPE pipes is essential for pipe safety evaluation under traffic loading. However, existing methods cannot accurately estimate the bending moment in HDPE pipes due to neglecting the installation effect and the pipe-soil interaction under traffic loading. The installation of pipes generates an initial bending moment in the pipe, which should be included in the pipe bending moment calculation. The pipe-soil interaction dominates the load sharing between the pipe and the soil and thus influences the bending moment in the pipe under traffic loading. In this study, numerical modeling was used to investigate the bending moment in HDPE pipes caused by traffic loading. A field trial was firstly used to verify the effectiveness of the numerical modeling procedure. Subsequently, the effects of traffic load magnitude, soil cover thickness, pipe diameter, and pipe stiffness on the maximum bending moment were investigated. An empirical method was then proposed to predict the maximum bending moment in the HDPE pipe caused by the traffic loading based on the numerical results. Finally, a case history from the literature was used to validate the proposed method.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code generated or used during the study are available from the corresponding author by request.
References
AASHTO. 2002. Standard specifications for highway bridges. 17th ed. Washington, DC: AASHTO.
AASHTO. 2012. LRFD bridge design specifications. 2nd ed. Washington, DC: AASHTO.
Acharya, R., J. Han, J. J. Brennan, R. L. Parsons, and D. K. Khatri. 2016. “Structural response of a low-fill box culvert under static and traffic loading.” J. Perform. Constr. Facil. 30 (1): 04014184. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000690.
Arockiasamy, M., O. Chaallal, and T. Limpeteeprakarn. 2006. “Full-scale field tests on flexible pipes under live load application.” J. Perform. Constr. Facil. 20 (1): 21–27. https://doi.org/10.1061/(ASCE)0887-3828(2006)20:1(21).
ASTM. 2011. Standard practice for classification of soils for engineering purpose. ASTM D2487-11. West Conshohocken, PA: ASTM.
ASTM. 2012. Standard test methods for laboratory compaction characteristics of soil using modified effort. ASTM D1557-12. West Conshohocken, PA: ASTM.
Burmister, D. M. 1958. “Evaluation of pavement systems of the WASHO road test by layered system method.” Highway Res. Board Bull. 177: 25–54.
Cao, W. 1994. “Three-dimensional finite element analysis of buried pipes.” Ph.D. dissertation, Dept. of Civil Engineering, Technical Univ. of Nova Scotia.
CECS (China Association for Engineering Construction Standardization). 2004. Technical specification for buried PE pipeline of sewer engineering. Beijing: China Architecture and Building Press.
Corey, R., J. Han, D. K. Khatri, and R. L. Parsons. 2014. “Laboratory study on geosynthetic protection of buried steel-reinforced HDPE pipes from static loading.” J. Geotech. Geoenviron. Eng. 140 (6): 04014019. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001113.
Dhar, A. S., I. D. Moore, and T. J. McGrath. 2004. “Two-dimensional analyses of thermoplastic culvert deformations and strains.” J. Geotech. Geoenviron. Eng. 130 (2): 199–208. https://doi.org/10.1061/(ASCE)1090-0241(2004)130:2(199).
Elshimi, T. M., and I. D. Moore. 2013. “Modeling the effects of backfilling and soil compaction beside shallow buried pipes.” J. Pipeline Syst. Eng. Pract. 4 (4): 04013004. https://doi.org/10.1061/(ASCE)PS.1949-1204.0000136.
Katona, M. G. 1976. CANDE: A modern approach for the structural design and analysis of buried culverts. Washington, DC: Federal Highway Administration.
McGrath, T. J. 2005. Performance of thermoplastic pipe under highway vehicle loading. St. Paul, MN: Minnesota DOT.
McGrath, T. J., I. D. Moore, E. T. Selig, M. C. Webb, and B. Taleb. 2002. Recommended specifications for large span culverts. Washington, DC: Transportation Research Board.
McGrath, T. J., E. T. Selig, M. C. Webb, and G. V. Zoladz. 1999. Pipe interaction with the backfill envelope. Washington, DC: Federal Highway Administration.
Moore, I. D. 1987. “Response of buried cylinder to surface loads.” J. Geotech. Eng. 113 (7): 758–773. https://doi.org/10.1061/(ASCE)0733-9410(1987)113:7(758).
Petersen, D. L., C. R. Nelson, G. Li, T. J. McGrath, and Y. Kitane. 2010. Recommended design specifications for live load distribution to buried structures. Washington, DC: Transportation Research Board.
Phrase, B. M. 1996. “High density polyethylene pipe in highway applications.” M.S. thesis, Dept. of Civil and Construction Engineering, Iowa State Univ.
Wang, F., Y. J. Du, and X. M. Yang. 2015. “Physical modeling on ground response to tunneling in sand considering the existence of HDPE pipes.” ASTM Geotech. Test. J. 38 (1): 1–13.
Wang, F., Y. J. Du, M. Zhou, and Y. J. Zhang. 2016. “Experimental study of the effects produced by a backfilling process on full-scale buried corrugated HDPE pipes in fine-grained soils.” J. Pipeline Syst. Eng. Pract. 7 (1): 05015001. https://doi.org/10.1061/(ASCE)PS.1949-1204.0000208.
Wang, F., J. Han, R. Corey, R. L. Parsons, and X. Sun. 2017. “Numerical modeling of installation of steel-reinforced high-density polyethylene pipes in soil.” J. Geotech. Geoenviron. Eng. 143 (11): 04017084. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001784.
Wang, F., J. Han, R. Parsons, and R. Corey. 2020. “Performance of steel-reinforced high-density polyethylene pipes in soil during installation: A numerical study.” Acta Geotech. 15 (4): 963–974. https://doi.org/10.1007/s11440-019-00822-w.
Wang, Y. Q., X. G. Niu, and Q. W. Tan. 2011. “Safety analysis for buried gas pipelines under heavy vehicle loads.” [In Chinese.] J. Saf. Sci. Technol. 7 (8): 109–114.
Watkins, R. K., and L. R. Anderson. 2000. Structural mechanics of buried pipes. New York: CRC Press.
Zhang, C., and I. D. Moore. 1998. “Nonlinear finite element analysis for thermoplastic pipes.” Transp. Res. Rec. 1624 (1): 225–230. https://doi.org/10.3141/1624-26.
Zhang, Y. J. 2013. “Study on deformation and control technology with dynamic characteristics of low embankment under traffic loading.” [In Chinese.] Ph.D. dissertation, Dept. of Underground Engineering, Southeast Univ.
Zhou, M., Y. J. Du, F. Wang, A. Arulrajah, S. Horpibulsuk, and X. G. Qin. 2017. “Earth pressures on the trenched HDPE pipes in fine-grained soils during construction phase: Full-scale field trial and finite element modeling.” Transp. Geotech. 12: 56–69. https://doi.org/10.1016/j.trgeo.2017.08.002.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Jul 3, 2020
Accepted: Oct 12, 2020
Published online: Jan 7, 2021
Published in print: May 1, 2021
Discussion open until: Jun 7, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.