Structural Evaluation of Flexible Pavement Constructed with Steel Slag–Fly Ash–Lime Mix in the Base Layer
Publication: Journal of Materials in Civil Engineering
Volume 33, Issue 6
Abstract
The concept of utilizing industrial wastes for road construction can be materialized only by evaluating the field performance of roads constructed with these wastes. The present study encompasses the laboratory investigation of steel slag–fly ash–lime (SFL) mix substantiated by field evaluation of flexible pavement test sections constructed with SFL mix in the base layer. Based on grain size analysis and unconfined compressive strength (UCS) test, 75% steel fly lime mix was chosen as a potential replacement for wet mix macadam (WMM) in the base layer of flexible pavement. The UCS test results were supported by the shear strength parameters and resilient moduli of optimum SFL mix. The superior stiffness characteristics of the SFL mix obtained in laboratory investigation were validated with a detailed structural evaluation of flexible pavement test sections constructed with 150 and 250 mm thick SFL base. Stiffness-based quality control approach was adopted during the construction of test sections through light weight deflectometer (LWD). SFL base layers exhibited higher in situ stiffness when compared to that of WMM. From the structural evaluation of test sections with falling weight deflectometer (FWD), sections with SFL base layer exhibited lower peak deflections than that of conventional WMM. The back-calculated elastic modulus computed from FWD test for SFL base layers was more than five times that of WMM. Furthermore, test sections with SFL base layer showed a service life ratio up to 2.6 and a notable cost saving up to 15% compared to conventional WMM layer.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors would like to thank the Department of Science and Technology, Ministry of Science and Technology, India (Grant No. DST/TSG/WM/2015/521/G) for funding this research. The authors also appreciate the Road and Building Department, Surat, Gujarat, India for the execution of test sections.
References
AASHTO. 2000. Determining the resilient modulus of soils and aggregate materials. AASHTO T 307. Washington, DC: AASHTO.
Akinwumi, I. I., J. B. Adeyeri, and O. A. Ejohwomu. 2013. “Effects of steel slag addition on the plasticity, strength and permeability of lateritic soil.” In Proc., Int. Conf. on Sustainable Design, Engineering, and Construction 2012, 457–464. Lawrence, KS: Construction Institute of ASCE, Univ. of Kansas. https://doi.org/10.1061/9780784412688.055.
ASTM. 2007. Standard test method for measuring deflections with a lightweight deflectometer (LWD). ASTM D2583. West Conshohocken, PA: ASTM.
ASTM. 2009a. Standard specification for coal fly ash and raw or calcined natural pozzolan for use as a mineral admixture in concrete. ASTM C618. West Conshohocken, PA: ASTM.
ASTM. 2009b. Standard test methods for unconfined compressive strength of compacted soil-lime mixtures. ASTM D5102. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard specification for graded aggregate material for bases or subbases for highways or airports. ASTM D2940. West Conshohocken, PA: ASTM.
ASTM. 2019. Standard test method for potential expansion of aggregates from hydration reactions. ASTM D4792. West Conshohocken, PA: ASTM.
Bakare, M. D., R. R. Pai, S. Patel, and J. T. Shahu. 2019. “Environmental sustainability by bulk utilization of fly ash and GBFS as road subbase materials.” J. Hazard. Toxic Radioact. Waste 23 (4): 04019011. https://doi.org/10.1061/(ASCE)HZ.2153-5515.0000450.
Barstis, W. F., and J. Metcalf. 2005. “Practical approach to criteria for the use of lime-fly ash stabilization in base courses.” Transp. Res. Rec. 1936 (1): 20–27. https://doi.org/10.1177/0361198105193600103.
Bazi, G., R. Briggs, S. Saboundjian, and P. Ullidtz. 2015. “Seasonal effects on a low-volume road flexible pavement.” Transp. Res. Rec. 2510 (1): 81–89. https://doi.org/10.3141/2510-10.
BIS (Bureau of Indian Standards). 2002. Classification and identification of soils for general engineering purposes. IS 1498. New Delhi, India: BSI.
BIS (Bureau of Indian Standards). 2005. Determination of dry density of soils in place, by the sand replacement method. IS 2720 Part 28. New Delhi, India: BSI.
BIS (Bureau of Indian Standards). 2010. Methods of sampling and test for quicklime and hydrated lime. IS 1514. New Delhi, India: BSI.
BIS (Bureau of Indian Standards). 2015. Determination of water content-dry density relation using heavy compaction. IS 2720 Part 8. New Delhi, India: BSI.
CEA (Central Electricity Authority). 2018. “Report on fly ash generation at coal/lignite based thermal power stations and its utilization in the country for the year 2017–18.” Accessed February 1, 2019. http://www.cea.nic.in/.
Consoli, N. C., P. D. M. Prietto, J. A. H. Carraro, and K. S. Heineck. 2001. “Behavior of compacted soil-fly ash-carbide lime mixtures.” J. Geotech. Geoenviron. Eng. 127 (9): 774–782. https://doi.org/10.1061/(ASCE)1090-0241(2001)127:9(774).
Dawson, T. A., G. Y. Baladi, C. P. Sessions, and S. W. Haider. 2009. “Backcalculated and laboratory-measured resilient modulus values.” Transp. Res. Rec. 2094 (1): 71–78. https://doi.org/10.3141/2094-08.
FHWA (Federal Highway Administration). 1994. Pavement deflection analysis. FHWA-HI-94-021. Washington, DC: USDOT.
FHWA (Federal Highway Administration). 2015. National performance management measures: Assessing pavement condition for the national highway performance program and bridge condition for the national highway performance program. FHWA-2013-0053. Washington, DC: USDOT.
Fleming, P. R., M. W. Frost, and J. P. Lambert. 2007. “Review of lightweight deflectometer for routine in-situ assessment of pavement material stiffness.” Transp. Res. Rec. 2004 (1): 80–87. https://doi.org/10.3141/2004-09.
Hall, K. T., M. I. Darter, T. E. Hoemer, and L. Khazanovich. 1997. LTPP data analysis-phase I: Validation of guidelines for k-value selection and concrete pavement performance prediction. Washington, DC: USDOT.
Huang, Y. H. 2004. Pavement analysis and design. 2nd ed. Upper Saddle River, NJ: Pearson.
IRC (Indian Road Congress). 1972. Traffic census on non-urban roads. IRC 9. New Delhi, India: IRC.
IRC (Indian Road Congress). 2002. Rural roads manual. IRC SP 20. New Delhi, India: IRC.
IRC (Indian Road Congress). 2004. Guidelines for surface evenness of highway pavements. IRC SP 16. New Delhi, India: IRC.
IRC (Indian Road Congress). 2012. Guidelines for the design of flexible pavements—Third revision.” IRC 37. New Delhi, India: IRC.
IRC (Indian Road Congress). 2015. Guidelines for structural evaluation and strengthening of flexible road pavement using Falling weight deflectometer (FWD) technique. IRC 115. New Delhi, India: IRC.
Johanneck, L., and D. Shongtao. 2013. “Responses and performance of stabilized full-depth reclaimed pavements at the Minnesota road research facility.” Transp. Res. Rec. 2368 (1): 114–125. https://doi.org/10.3141/2368-11.
John, E. 1984. “Steel slag utilization in asphalt mixes.” Proc. Can. Tech. Asphalt Assoc. 186 (1): 1–11.
Kumar, R., V. K. Adigopula, and S. D. Guzzarlapudi. 2017. “Stiffness-based quality control evaluation of modified subgrade soil using lightweight deflectometer.” J. Mater. Civ. Eng. 29 (9): 04017137. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001958.
Li, L., C. H. Benson, T. B. Edil, B. Hatipoglu, and O. Tastan. 2007. “Evaluation of recycled asphalt pavement material stabilized with fly ash.” In Proc., GeoDenver, 1–10. Reston, VA: ASCE.
Mooney, M. A., and P. K. Miller. 2009. “Analysis of lightweight deflectometer test based on in situ stress and strain response.” J. Geotech. Geoenviron. Eng. 135 (2): 199–208. https://doi.org/10.1061/(ASCE)1090-0241(2009)135:2(199).
MORTH (Ministry of Road Transport and Highways). 2013. Specifications for road and bridge works (5th revision). New Delhi, India: Indian Road Congress.
Mucka, P. 2016. “International roughness Index specifications around the world.” Road Mater. Pavement Des. 18 (4): 929–965. https://doi.org/10.1080/14680629.2016.1197144.
NCHRP (National Cooperative Highway Research Program). 1976. Lime-fly ash-stabilized bases and subbases. Washington, DC: NCHRP.
NCHRP (National Cooperative Highway Research Program). 1997. Laboratory determination of resilient modulus for flexible pavement design. Washington, DC: Transportation Research Board.
NCHRP (National Cooperative Highway Research Program). 2003. Harmonized test methods for laboratory determination of resilient modulus for flexible pavement design. Washington, DC: NCHRP.
NCHRP (National Cooperative Highway Research Program). 2004. Guide for mechanistic-empirical design of new and rehabilitated pavement structures. Part 2: Design inputs. Washington, DC: NCHRP.
Patel, S., and J. T. Shahu. 2016. “Resilient response and permanent strain of steel slag-fly ash-dolime mix.” J. Mater. Civ. Eng. 28 (10): 04016106. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001619.
Patel, S., and J. T. Shahu. 2017. “Comparative study of slags stabilized with fly ash and dolime for utilization in base course.” J. Mater. Civ. Eng. 29 (10): 04017168. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002017.
Patel, S., and J. T. Shahu. 2018. “Comparison of industrial waste mixtures for use in subbase course of flexible pavements.” J. Mater. Civ. Eng. 30 (7): 04018124. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002320.
Puppala, A. J., L. R. Hoyos, and A. K. Potturi. 2011. “Resilient moduli response of moderately cement-treated reclaimed asphalt pavement aggregates.” J. Mater. Civ. Eng. 23 (7): 990–998. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000268.
Saghafi, B., H. A. Nageim, and W. Atherton. 2013. “Mechanical behavior of a new base material containing high volumes of limestone waste dust, PFA, and APC residues.” J. Mater. Civ. Eng. 25 (4): 450–461. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000517.
Shen, W., M. Zhou, W. Ma, J. Hu, and Z. Cai. 2009. “Investigation on the application of steel slag-fly ash-phosphogypsum solidified material as road base material.” J. Hazard. Mater. 164 (1): 99–104. https://doi.org/10.1016/j.jhazmat.2008.07.125.
Tanyu, B. F., W. H. Kim, T. B. Edil, and C. H. Benson. 2003. “Comparison of laboratory resilient modulus with back-calculated elastic moduli from large-scale model experiments and FWD tests on granular materials.” In Resilient modulus testing for pavement components, 191–208. West Conshohocken, PA: ASTM.
USEPA. 1992. Toxicity characteristic leaching procedure. Washington, DC: USEPA.
World Steel Association. 2020. “Global crude steel output in 2019.” Accessed February 4, 2020. https://www.worldsteel.org/.
Yildirim, I. Z., and M. Prezzi. 2015. “Geotechnical properties of fresh and aged basic oxygen furnace steel slag.” J. Mater. Civ. Eng. 27 (12): 04015046. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001310.
Yildirim, I. Z., and M. Prezzi. 2017. “Experimental evaluation of EAF ladle steel slag as a geo-fill material: Mineralogical, physical and mechanical properties.” Constr. Build. Mater. 154 (Nov): 23–33. https://doi.org/10.1016/j.conbuildmat.2017.07.149.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Apr 7, 2020
Accepted: Oct 13, 2020
Published online: Mar 22, 2021
Published in print: Jun 1, 2021
Discussion open until: Aug 22, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.