Dynamic Mechanical Properties of Self-Compacting Rubberized Concrete under High Strain Rates
Publication: Journal of Materials in Civil Engineering
Volume 33, Issue 2
Abstract
Self-compacting rubberized concrete (SCRC), as the primary material of road construction, is produced by adding rubber particles instead of sand to self-compacting concrete (SCC). Four kinds of concrete with different rubber contents (0%, 5%, 10%, and 15%) are tested in this study. The materials testing systems (MTS) and split Hopkinson pressure bar (SHPB) are employed to obtain quasi-static mechanical properties (compressive, splitting tensile, and bending) and dynamic mechanical properties at high strain rates (). The results reveal that quasi-static mechanical strength decreases with the increase in rubber content. Compared with SCC, SCRC is dramatically high in ductility. With the increase of the strain rate, the dynamic compressive strength, peak toughness, specific energy absorption (SEA), and dynamic increase factors (DIF) all rise. The dynamic compressive strength decreases with the ascending of rubber content, while the toughness index, peak toughness, and SEA increase with the increasing rubber content. Exponential and linear fittings are utilized to help further understand the influence of strain rates. The craze-shear band-cavitation theory can also help well explain the transition strain rate of peak toughness curves. The failure modes under high strain rates are observed. The results reveal that SCRC exhibits a stronger sensitivity to rubber content and has better impact toughness than SCC.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and codes generated or utilized during the study appear in the published article.
Acknowledgments
This paper was supported by the National Natural Science Foundation of China (Grant Nos. 51979156, 51778623, and 51779134) and the Open Research Fund of State Key Laboratory of Research Center on Levee Safety Disaster Prevention, MWR, (Grant No. 2019002), granted to the corresponding author, Xiaojing Li.
References
Aamr-Daya, E., T. Langlet, A. Benazzouk, and M. Quéneudec. 2008. “Feasibility study of lightweight cement composite containing flax by-product particles: Physico-mechanical properties.” Cem. Concr. Compos. 30 (10): 957–963. https://doi.org/10.1016/j.cemconcomp.2008.06.002.
Al-Tayeb, M. M., B. A. Bakar, H. M. Akil, and H. Ismail. 2013a. “Performance of rubberized and hybrid rubberized concrete structures under static and impact load conditions.” Exp. Mech. 53 (3): 377–384. https://doi.org/10.1007/s11340-012-9651-z.
Al-Tayeb, M. M., B. A. Bakar, H. Ismail, and H. M. Akil. 2012. “Impact resistance of concrete with partial replacements of sand and cement by waste rubber.” Polym. Plast. Technol. Eng. 51 (12): 1230–1236. https://doi.org/10.1080/03602559.2012.696767.
Al-Tayeb, M. M., B. A. Bakar, H. Ismail, and H. M. Akil. 2013b. “Effect of partial replacement of sand by fine crumb rubber on impact load behavior of concrete beam: Experiment and nonlinear dynamic analysis.” Mater. Struct. 46 (8): 1299–1307. https://doi.org/10.1617/s11527-012-9974-3.
ASTM. 1997. Standard test method for flexural toughness and first-crack strength of fiber-reinforced concrete (using beam with third-point loading). ASTM C1018/C1018-M. West Conshohocken, PA: ASTM.
ASTM. 2002. Standard test method for compressive strength of hydraulic-cement mortars (using portions of prisms broken in flexure). ASTM C349. West Conshohocken, PA: ASTM.
ASTM. 2004. Standard practice for making and curing concrete tests specimens in the laboratory. ASTM C192-98. West Conshohocken, PA: ASTM.
ASTM. 2005. Standard specification for portland cement. ASTM C150-04a. West Conshohocken, PA: ASTM.
ASTM. 2011. Standard test method for splitting tensile strength of cylindrical concrete specimens. ASTM C496/C496M-11. West Conshohocken, PA: ASTM.
Atahan, A. O., and U. K. Sevim. 2008. “Testing and comparison of concrete barriers containing shredded waste tire chips.” Mater. Lett. 62 (21): 3754–3757. https://doi.org/10.1016/j.matlet.2008.04.068.
Atahan, A. O., and A. Ö. Yücel. 2012. “Crumb rubber in concrete: Static and dynamic evaluation.” Constr. Build. Mater. 36 (36): 617–622. https://doi.org/10.1016/j.conbuildmat.2012.04.068.
Bai, E. L., J. Y. Xu, S. Lu, K. X. Lin, and Y. M. Zhang. 2018. “Comparative study on the dynamic properties of lightweight porous concrete.” RSC Adv. 8 (26): 14454–14461. https://doi.org/10.1039/C8RA00082D.
Bernal, S. A., R. M. de Gutiérrez, A. L. Pedraza, J. L. Provis, E. D. Rodriguez, and S. Delvasto. 2011. “Effect of binder content on the performance of alkali-activated slag concretes.” Cem. Concr. Res. 41 (1): 1–8. https://doi.org/10.1016/j.cemconres.2010.08.017.
Bignozzi, M. C., and F. Sandrolini. 2006. “Tyre rubber waste recycling in self-compacting concrete.” Cem. Concr. Res. 36 (4): 735–739. https://doi.org/10.1016/j.cemconres.2005.12.011.
Bischoff, P. H., and S. H. Perry. 1991. “Compressive behaviour of concrete at high strain rates.” Mater. Struct. 24 (6): 425–450. https://doi.org/10.1007/BF02472016.
Carroll, J. C., and N. Helminger. 2016. “Fresh and hardened properties of fiber-reinforced rubber concrete.” J. Mater. Civ. Eng. 28 (7): 04016027. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001541.
CEB-FIP (Committee Euro-International for Concrete-International Federation for Prestressing). 1994. CEB-FIP model code 1990: Design code 1994. London: Thomas Telford.
Chen, F., B. Qiu, B. Wang, Y. Shangguan, and Q. Zheng. 2015. “Balanced toughening and strengthening of ethylene–propylene rubber toughened isotactic polypropylene using a poly (styrene-b-ethylene–propylene) diblock copolymer.” RSC Adv. 5 (27): 20831–20837. https://doi.org/10.1039/C5RA00386E.
Chen, X., L. Ge, J. Zhou, and S. Wu. 2016. “Experimental study on split Hopkinson pressure bar pulse-shaping techniques for concrete.” J. Mater. Civ. Eng. 28 (5): 04015196. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001494.
Chen, X., Z. Liu, S. Guo, Y. Huang, and W. Xu. 2019. “Experimental study on fatigue properties of normal and rubberized self-compacting concrete under bending.” Constr. Build. Mater. 205 (Apr): 10–20. https://doi.org/10.1016/j.conbuildmat.2019.01.207.
Chen, X., S. Wu, and J. Zhou. 2013. “Experimental and modeling study of dynamic mechanical properties of cement paste, mortar and concrete.” Constr. Build. Mater. 47 (Oct): 419–430. https://doi.org/10.1016/j.conbuildmat.2013.05.063.
Dong, S., B. Han, X. Yu, and J. Ou. 2018. “Dynamic impact behaviors and constitutive model of super-fine stainless wire reinforced reactive powder concrete.” Constr. Build. Mater. 184 (Sep): 602–616. https://doi.org/10.1016/j.conbuildmat.2018.07.027.
EFNARC. 2005. “The European guidelines for self-compacting concrete: Specification, production and use.” Accessed August 1, 2017. https://www.efnarc.org.
Fattuhi, N. I., and L. A. Clark. 1996. “Cement-based materials containing shredded scrap truck tyre rubber.” Constr. Build. Mater. 10 (4): 229–236. https://doi.org/10.1016/0950-0618(96)00004-9.
Feng, W., F. Liu, F. Yang, L. Li, and L. Jing. 2018. “Experimental study on dynamic split tensile properties of rubber concrete.” Constr. Build. Mater. 165 (Mar): 675–687. https://doi.org/10.1016/j.conbuildmat.2018.01.073.
Frew, D. J., M. J. Forrestal, and W. Chen. 2002. “Pulse shaping techniques for testing brittle materials with a split Hopkinson pressure bar.” Exp. Mech. 42 (1): 93–106. https://doi.org/10.1007/BF02411056.
Fu, Q., D. Niu, J. Zhang, D. Huang, Y. Wang, M. Hong, and L. Zhang. 2018. “Dynamic compressive mechanical behaviour and modelling of basalt–polypropylene fibre-reinforced concrete.” Arch. Civ. Mech. Eng. 18 (3): 914–927. https://doi.org/10.1016/j.acme.2018.01.016.
Gao, J., W. Sun, and K. Morino. 1997. “Mechanical properties of steel fiber-reinforced, high-strength, lightweight concrete.” Cem. Concr. Compos. 19 (4): 307–313. https://doi.org/10.1016/S0958-9465(97)00023-1.
Grote, D. L., S. W. Park, and M. Zhou. 2001. “Dynamic behavior of concrete at high strain rates and pressures: Part I. Experimental characterization.” Int. J. Impact Eng. 25 (9): 869–886. https://doi.org/10.1016/S0734-743X(01)00020-3.
Güneyisi, E. 2010. “Fresh properties of self-compacting rubberized concrete incorporated with fly ash.” Mater. Struct. 43 (8): 1037–1048. https://doi.org/10.1617/s11527-009-9564-1.
Gupta, T., S. Chaudhary, and R. K. Sharma. 2016. “Mechanical and durability properties of waste rubber fiber concrete with and without silica fume.” J. Cleaner Prod. 112 (Part 1): 702–711. https://doi.org/10.1016/j.jclepro.2015.07.081.
Gupta, T., R. K. Sharma, and S. Chaudhary. 2015. “Impact resistance of concrete containing waste rubber fiber and silica fume.” Int. J. Impact Eng. 83 (Sep): 76–87. https://doi.org/10.1016/j.ijimpeng.2015.05.002.
Gupta, T., S. Siddique, R. K. Sharma, and S. Chaudhary. 2019. “Behaviour of waste rubber powder and hybrid rubber concrete in aggressive environment.” Constr. Build. Mater. 217 (Aug): 283–291. https://doi.org/10.1016/j.conbuildmat.2019.05.080.
Hartmann, T., A. Pietzsch, and N. Gebbeken. 2010. “A hydrocode material model for concrete.” Int. J. Prot. Struct. 1 (4): 443–468. https://doi.org/10.1260/2041-4196.1.4.443.
Hesami, S., I. S. Hikouei, and S. A. A. Emadi. 2016. “Mechanical behavior of self-compacting concrete pavements incorporating recycled tire rubber crumb and reinforced with polypropylene fiber.” J. Cleaner Prod. 133 (133): 228–234. https://doi.org/10.1016/j.jclepro.2016.04.079.
Jentzsch, J., K. Krause, J. Marz, and K. Weber. 1981. “Testing method and device for the determination of mechanical-properties of rubber blends and rubber products.” Plaste Kautsch. 28 (11): 625–628.
Jiang F. 2004. “The research on the dynamic behavior on rubberized concrete by using split Hopkinson pressure bar.” [In Chinese.] Master dissertation, College of Civil Engineering, Hunan Univ.
Katayama, M., M. Itoh, S. Tamura, M. Beppu, and T. Ohno. 2007. “Numerical analysis method for the RC and geological structures subjected to extreme loading by energetic materials.” Int. J. Impact Eng. 34 (9): 1546–1561. https://doi.org/10.1016/j.ijimpeng.2006.10.013.
Khalil, E., M. Abd-Elmohsen, and A. M. Anwar. 2015. “Impact resistance of rubberized self-compacting concrete.” Water Sci. 29 (1): 45–53. https://doi.org/10.1016/j.wsj.2014.12.002.
Kim, B., and W. J. Weiss. 2003. “Using acoustic emission to quantify damage in restrained fiber-reinforced cement mortars.” Cem. Concr. Res. 33 (2): 207–214. https://doi.org/10.1016/S0008-8846(02)00978-X.
Lai, J., and W. Sun. 2009. “Dynamic behaviour and visco-elastic damage model of ultra-high performance cementitious composite.” Cem. Concr. Res. 39 (11): 1044–1051. https://doi.org/10.1016/j.cemconres.2009.07.012.
Lee, S., K. M. Kim, and J. Y. Cho. 2017. “Investigation into pure rate effect on dynamic increase factor for concrete compressive strength.” Procedia Eng. 210: 11–17. https://doi.org/10.1016/j.proeng.2017.11.042.
Li, L. J., G. R. Tu, C. Lan, and F. Liu. 2016. “Mechanical characterization of waste-rubber-modified recycled-aggregate concrete.” J. Cleaner Prod. 124 (Jun): 325–338. https://doi.org/10.1016/j.jclepro.2016.03.003.
Li, Q. M., and H. Meng. 2003. “About the dynamic strength enhancement of concrete-like materials in a split Hopkinson pressure bar test.” Int. J. Solids Struct. 40 (2): 343–360. https://doi.org/10.1016/S0020-7683(02)00526-7.
Li, Q. M., S. R. Reid, H. M. Wen, and A. R. Telford. 2005. “Local impact effects of hard missiles on concrete targets.” Int. J. Impact Eng. 32 (1): 224–284. https://doi.org/10.1016/j.ijimpeng.2005.04.005.
Li, X., F. Rao, S. Song, M. A. Corona-Arroyo, N. Ortiz-Lara, and E. A. Aguilar-Reyes. 2018. “Effects of aggregates on the mechanical properties and microstructure of geothermal metakaolin-based geopolymers.” Results Phys. 11 (Dec): 267–273. https://doi.org/10.1016/j.rinp.2018.09.018.
Li, Z., J. Xu, and E. Bai. 2012. “Static and dynamic mechanical properties of concrete after high temperature exposure.” Mater. Sci. Eng., A 544 (May): 27–32. https://doi.org/10.1016/j.msea.2012.02.058.
Liu, F., G. Chen, L. Li, and Y. Guo. 2012. “Study of impact performance of rubber reinforced concrete.” Constr. Build. Mater. 36 (Nov): 604–616. https://doi.org/10.1016/j.conbuildmat.2012.06.014.
Ma, Q., and C. Gao. 2018. “Effect of basalt fiber on the dynamic mechanical properties of cement-soil in SHPB test.” J. Mater. Civ. Eng. 30 (8): 04018185. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002386.
Medina, N. F., D. F. Medina, F. Hernández-Olivares, and M. A. Navacerrada. 2017. “Mechanical and thermal properties of concrete incorporating rubber and fibres from tyre recycling.” Constr. Build. Mater. 144 (Jul): 563–573. https://doi.org/10.1016/j.conbuildmat.2017.03.196.
Moustafa, A., and M. A. ElGawady. 2015. “Mechanical properties of high strength concrete with scrap tire rubber.” Constr. Build. Mater. 93 (Sep): 249–256. https://doi.org/10.1016/j.conbuildmat.2015.05.115.
Murr, L. E., K. P. Staudhammer, and S. S. Hecker. 1982. “Effects of strain state and strain rate on deformation-induced transformation in 304 stainless steel: Part II. Microstructural study.” Metall. Trans. A 13 (4): 627–635. https://doi.org/10.1007/BF02644428.
Nagataki, S., and H. Fujiwara. 1995. “Self-compacting property of highly flowable concrete.” In Proc., 2nd CANMET/ACI Int. Symp. on Advances in Concrete Technology, 301–314. Naples, FL: American Concrete Institute. https://doi.org/10.14359/960.
Najim, K. B., and M. R. Hall. 2012. “Mechanical and dynamic properties of self-compacting crumb rubber modified concrete.” Constr. Build. Mater. 27 (1): 521–530. https://doi.org/10.1016/j.conbuildmat.2011.07.013.
Ngo, T., P. Mendis, and T. Krauthammer. 2007. “Behavior of ultrahigh-strength prestressed concrete panels subjected to blast loading.” J. Struct. Eng. 133 (11): 1582–1590. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:11(1582).
Papakonstantinou, C. G., and M. J. Tobolski. 2006. “Use of waste tire steel beads in portland cement concrete.” Cem. Concr. Res. 36 (9): 1686–1691. https://doi.org/10.1016/j.cemconres.2006.05.015.
Pham, T. M., M. Elchalakani, A. Karrech, and H. Hao. 2019. “Axial impact behavior and energy absorption of rubberized concrete with/without fiber-reinforced polymer confinement.” Int. J. Prot. Struct. 10 (2): 154–173. https://doi.org/10.1177/2041419618800771.
Reda Taha, M. M., A. S. El-Dieb, M. A. Abd El-Wahab, and M. E. Abdel-Hameed. 2008. “Mechanical, fracture, and microstructural investigations of rubber concrete.” J. Mater. Civ. Eng. 20 (10): 640–649. https://doi.org/10.1061/(ASCE)0899-1561(2008)20:10(640).
Ross, C. A., J. W. Tedesco, and S. T. Kuennen. 1995. “Effects of strain rate on concrete strength.” Mater. J. 92 (1): 37–47. https://doi.org/10.14359/1175.
Shi, D., and X. Chen. 2018. “Flexural tensile fracture behavior of pervious concrete under static preloading.” J. Mater. Civ. Eng. 30 (11): 06018015. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002477.
Siddique, R., and T. R. Naik. 2004. “Properties of concrete containing scrap-tire rubber—An overview.” Waste Manage. 24 (6): 563–569. https://doi.org/10.1016/j.wasman.2004.01.006.
Son, K. S., I. Hajirasouliha, and K. Pilakoutas. 2011. “Strength and deformability of waste tyre rubber-filled reinforced concrete columns.” Constr. Build. Mater. 25 (1): 218–226. https://doi.org/10.1016/j.conbuildmat.2010.06.035.
Su, Y., J. Li, C. Wu, P. Wu, and Z. X. Li. 2016. “Effects of steel fibres on dynamic strength of UHPC.” Constr. Build. Mater. 114 (Jul): 708–718. https://doi.org/10.1016/j.conbuildmat.2016.04.007.
Tedesco, J. W., and C. A. Ross. 1998. “Strain-rate-dependent constitutive equations for concrete.” J. Pressure Vessel Technol. 120 (4): 398–405. https://doi.org/10.1115/1.2842350.
Topçu, I. B. 1995. “The properties of rubberized concretes.” Cem. Concr. Res. 25 (2): 304–310. https://doi.org/10.1016/0008-8846(95)00014-3.
Topçu, I. B., and N. Avcular. 1997. “Collision behaviours of rubberized concrete.” Cem. Concr. Res. 27 (12): 1893–1898. https://doi.org/10.1016/S0008-8846(97)00204-4.
Toutanji, H. A. 1996. “The use of rubber tire particles in concrete to replace mineral aggregates.” Cem. Concr. Compos. 18 (2): 135–139. https://doi.org/10.1016/0958-9465(95)00010-0.
Van der Wal, A., J. J. Mulder, J. Oderkerk, and R. J. Gaymans. 1998. “Polypropylene–rubber blends: 1. The effect of the matrix properties on the impact behaviour.” Polymer 39 (26): 6781–6787. https://doi.org/10.1016/S0032-3861(98)00170-0.
Van der Wal, A., R. Nijhof, and R. J. Gaymans. 1999. “Polypropylene–rubber blends: 2. The effect of the rubber content on the deformation and impact behaviour.” Polymer 40 (22): 6031–6044. https://doi.org/10.1016/S0032-3861(99)00213-X.
Wang, C., W. Chen, H. Hao, S. Zhang, R. Song, and X. Wang. 2018. “Experimental investigations of dynamic compressive properties of roller compacted concrete (RCC).” Constr. Build. Mater. 168 (Apr): 671–682. https://doi.org/10.1016/j.conbuildmat.2018.02.112.
Wang, Y., H. C. Wu, and V. C. Li. 2000. “Concrete reinforcement with recycled fibers.” J. Mater. Civ. Eng. 12 (4): 314–319. https://doi.org/10.1061/(ASCE)0899-1561(2000)12:4(314).
Xue, J., and M. Shinozuka. 2013. “Rubberized concrete: A green structural material with enhanced energy-dissipation capability.” Constr. Build. Mater. 42 (May): 196–204. https://doi.org/10.1016/j.conbuildmat.2013.01.005.
Yan, P., Q. Fang, J. Zhang, L. Chen, and H. Wu. 2019. “Experimental and mesoscopic investigation of spherical ceramic particle concrete under static and impact loading.” Int. J. Impact Eng. 128 (Jun): 37–45. https://doi.org/10.1016/j.ijimpeng.2019.01.013.
Yung, W. H., L. C. Yung, and L. H. Hua. 2013. “A study of the durability properties of waste tire rubber applied to self-compacting concrete.” Constr. Build. Mater. 41 (Apr): 665–672. https://doi.org/10.1016/j.conbuildmat.2012.11.019.
Zheng, L., X. S. Huo, and Y. Yuan. 2008. “Experimental investigation on dynamic properties of rubberized concrete.” Constr. Build. Mater. 22 (5): 939–947. https://doi.org/10.1016/j.conbuildmat.2007.03.005.
Zhou, X. Q., and H. Hao. 2008. “Modelling of compressive behaviour of concrete-like materials at high strain rate.” Int. J. Solids Struct. 45 (17): 4648–4661. https://doi.org/10.1016/j.ijsolstr.2008.04.002.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Jul 19, 2019
Accepted: Jul 20, 2020
Published online: Nov 28, 2020
Published in print: Feb 1, 2021
Discussion open until: Apr 28, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.