Study of Lower Temperature–Sintered Enamel Coating on Steel Bars: Effect of Coating Cycles
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 9
Abstract
Enamel coating is a novel type of coating for the corrosion protection of reinforcement in concrete. Recently, improved enamel coating was achieved using low-temperature sintering. This study aims to investigate the effect of coating cycles on the microstructure, adhesion, and corrosion resistance of a lower temperature sintered enamel coating. Enamel coated steel bars with single, double, and triple coatings (SC, DC, and TC, respectively) and uncoated (UC) steel bars were prepared. X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive X-ray (EDX) spectroscopy, and pull-off and salt spray tests were performed. The results showed that both the DC and TC had fewer defects and exhibited excellent corrosion resistance compared with that of the SC. However, the transition layer formed at the enamel/steel interface for the DC and TC steel bars weakened the coating adhesion. The related corrosion mechanism was illustrated based on two different corrosion modes: corrosion that occurred at holes (COH) and corrosion that occurred at microcracks (COM).
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The authors would like to thank Zhenwen Xu for assistance in the experimental preparation part and Yu Peng in the microstructural observation part of this study. In addition, the authors appreciate the financial support from the National Science Foundation of China (Nos. 51522905, 51778570, and 51879230) and the Zhejiang Provincial Natural Science Foundation of China (No. LR15E090001).
References
ASTM. 2018. Standard practice for operating salt spray (fog) apparatus. ASTM B117. West Conshohocken, PA: ASTM.
Barcova, K., M. Mashlan, R. Zboril, J. Filip, J. Podjuklova, K. Hrabovska, and P. Schaaf. 2006. “Phase composition of steel–enamel interfaces: Effects of chemical pre-treatment.” Surf. Coat. Technol. 201 (3–4): 1836–1844. https://doi.org/10.1016/j.surfcoat.2006.03.015.
Bhadang, K. A., and K. Gross. 2004. “Influence of fluorapatite on the properties of thermally sprayed hydroxyapatite coatings.” Biomaterials 25 (20): 4935–4945. https://doi.org/10.1016/j.biomaterials.2004.02.043.
Bodaghi, M., and A. Davarpanah. 2011. “The influence of cobalt on the microstructure and adhesion characteristics of enamel on steel sheet.” Process. Appl. Ceram. 5 (4): 215–222. https://doi.org/10.2298/PAC1104215B.
Chen, M., W. Li, M. Shen, S. Zhu, and F. Wang. 2014. “Glass coatings on stainless steels for high-temperature oxidation protection: Mechanisms.” Corros. Sci. 82 (May): 316–327. https://doi.org/10.1016/j.corsci.2014.01.033.
Fan, L., F. Tang, S. T. Reis, G. Chen, and M. L. Koenigstein. 2017a. “Corrosion resistance of transmission pipeline steel coated with five types of enamels.” Acta Metall. Sinica. 30 (4): 390–398. https://doi.org/10.1007/s40195-017-0554-y.
Fan, L., F. Tang, S. T. Reis, G. Chen, and M. L. Koenigstein. 2017b. “Corrosion resistances of steel pipe internally coated with enamel.” Corrosion 73 (11): 1335–1345. https://doi.org/10.5006/2497.
ISO. 2002. Paints, varnishes and plastics: Pull-off test for adhesion. ISO 4624. Geneva: ISO.
Liu, C., A. Leyland, Q. Bi, and A. Matthews. 2001. “Corrosion resistance of multi-layered plasma-assisted physical vapour deposition TiN and CrN coatings.” Surf. Coat. Technol. 141 (2–3): 164–173. https://doi.org/10.1016/S0257-8972(01)01267-1.
Lupescu, M. B., M. Zaharescu, and A. Andrei. 1997. “Electron spectroscopy studies of the steel/enamel interface.” Mater. Sci. Eng. A (Struct. Mater.: Prop. Microstruct. Process.) 232 (1–2): 73–79. https://doi.org/10.1016/S0921-5093(97)00095-6.
Mackert, J. R., T. G. Conner, R. D. Ringle, E. E. Parry, and C. W. Fairhurst. 1992. “X-ray diffraction characterization of the enamel–steel interface.” J. Am. Ceram. Soc. 75 (11): 3087–3090. https://doi.org/10.1111/j.1151-2916.1992.tb04391.x.
Nuske, R. W., T. A. Bloom, and T. L. Schiller. 1991. “Fishscale resistance of enameling steels.” Ceram. Eng. Sci. Proc. 12 (5–6): 836–846. https://doi.org/10.1002/9780470313275.ch32.
Pan, H. B., and B. W. Darvell. 2007. “Solubility of calcium fluoride and fluorapatite by solid titration.” Arch. Oral Biol. 52 (9): 861–868. https://doi.org/10.1016/j.archoralbio.2007.03.002.
Qian, H., D. M. Yan, S. K. Chen, G. Chen, Y. Tian, and G. D. Chen. 2019. “Effect of high temperature exposure and strain rate on mechanical properties of high-strength steel rebars.” J. Mater. Civ. Eng. 31 (11): 04019261. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002906.
Ritchie, D., H. A. Schaeffer, and D. White. 1983. “The presence of an iron oxide layer at the enamel/steel interface in one-coat porcelain enameling.” J. Mater. Sci. 18 (2): 599–604. https://doi.org/10.1007/bf00560649.
Sahnesarayi, M. K., H. Sarpoolaky, and S. Rastegari. 2019. “Influence of multiple coating and heat treatment cycles on the performance of a coating in the protection of 316L stainless steel against corrosion under UV illumination and dark conditions.” Iran. J. Mater. Sci. Eng. 16 (2): 33–42.
Samiee, L., H. Sarpoolaky, and A. Mirhabibi. 2007. “Microstructure and adhesion of cobalt containing and cobalt free enamels to low carbon steel.” Mater. Sci. Eng. A. 458 (1–2): 88–95. https://doi.org/10.1016/j.msea.2006.12.108.
Shieu, F. S., K. C. Lin, and J. C. Wong. 1999. “Microstructure and adhesion of porcelain enamel to low carbon steel.” Ceram. Int. 25 (1): 27–34. https://doi.org/10.1016/S0272-8842(97)00080-1.
Striepe, S., H. Bornhöft, J. Deubener, and J. Wendel. 2016. “Microalloy precipitation at the glass–steel interface enabling adhesion of porcelain enamel.” Int. J. Appl. Ceram. Technol. 13 (1): 191–199. https://doi.org/10.1111/ijac.12435.
Tang, F., G. Chen, R. K. Brow, J. S. Volz, and M. L. Koenigstein. 2012a. “Corrosion resistance and mechanism of steel bar coated with three types of enamel.” Corros. Sci. 59 (157–168): 0–168. https://doi.org/10.1016/j.corsci.2012.02.024.
Tang, F., G. Chen, J. S. Volz, R. K. Brow, and M. Koenigstein. 2012b. “Microstructure and corrosion resistance of enamel coatings applied to smooth reinforcing steel.” Constr. Build. Mater. 35 (Oct): 376–384. https://doi.org/10.1016/j.conbuildmat.2012.04.059.
Tang, F., X. Cheng, G. Chen, R. K. Brow, J. S. Volz, and M. L. Koenigstein. 2013. “Electrochemical behavior of enamel-coated carbon steel in simulated concrete pore water solution with various chloride concentrations.” Electrochim. Acta. 92 (Mar): 36–46. https://doi.org/10.1016/j.electacta.2012.12.125.
Tang, F., G. Chen, and R. K. Brow. 2016. “Chloride-induced corrosion mechanism and rate of enamel- and epoxy-coated deformed steel bars embedded in mortar.” Cem. Concr. Res. 82 (Apr): 58–73. https://doi.org/10.1016/j.cemconres.2015.12.015.
Tao, Z., X. Q. Wang, and B. Uy. 2013. “Stress-strain curves of structural and reinforcing steels after exposure to elevated temperatures.” J. Mater. Civ. Eng. 25 (9): 1306–1316. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000676.
Wagner, W. C., K. Asgar, W. C. Bigelow, and R. A. Flinn. 1993. “Effect of interfacial variables on metal-porcelain bonding.” J. Biomed. Mater. Res. 27 (4): 531–537. https://doi.org/10.1002/jbm.820270414.
Werner, C. R., J. S. Volz, G. Chen, R. K. Brow, and M. L. Koenigstein. 2012. “Corrosion performance of reactive-enamel coated reinforcing steel.” ACI Mater. J. 109 (4): 441–450.
Yan, D., S. Reis, X. Tao, G. Chen, R. K. Brow, and M. Koenigstein. 2012. “Effect of chemically reactive enamel coating on bonding strength at steel/mortar interface.” Constr. Build. Mater. 28 (1): 512–518. https://doi.org/10.1016/j.conbuildmat.2011.08.075.
Yang, X., A. Jha, R. Brydson, and R. C. Cochrane. 2003. “An analysis of the microstructure and interfacial chemistry of steel–enamel interface.” Thin Solid Films 443 (1–2): 33–45. https://doi.org/10.1016/S0040-6090(03)00973-8.
Yang, X., A. Jha, R. C. Cochrane, and S. Ali. 2006. “Mass-transport processes at the steel-enamel interface.” Metall. Mater. Trans. B 37 (1): 89–98. https://doi.org/10.1007/s11663-006-0088-6.
Zhang, A., Z. Jiang, S. Jiao, and D. Wei. 2011. “Microstructure and adhesion of vitreous enamel to low carbon steel.” Int. J. Surf. Sci. Eng. 5 (5/6): 369–380. https://doi.org/10.1504/IJSURFSE.2011.044390.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Sep 24, 2019
Accepted: Mar 2, 2020
Published online: Jun 30, 2020
Published in print: Sep 1, 2020
Discussion open until: Nov 30, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.