Clinker Efficiency in the Treatment of Low-Plasticity Clay
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 8
Abstract
This paper presented some geotechnical characteristics of low plasticity clay (LPC) treated with clinker in comparison with those of ordinary portland cement (OPC) treated LPC. The chosen percentages of both additives were 10, 12, and 14% for the stabilization of LPC. While the liquid limits of clinker and OPC treated LPC decreased, their plastic limits increased. The liquid limit (LL) and the plastic limit (PL) of clinker treated LPC were found to be lower than those of OPC treated LPC. The optimum moisture content (OMC) and maximum dry density (MDD) of LPC were increased by both clinker and OPC treatment. In addition, the OMC values of clinker treated LPC were higher than those of OPC treated LPC. However, the MDD values of clinker and OPC treated LPC were almost the same. The shear strength of LPC was also increased with the clinker and OPC treatments under both the wet-cured and air-dried conditions. The compressibility and swell characteristics of LPC were considerably reduced by both clinker and OPC treatments. Nevertheless, the swell and compressibility of clinker treated LPC were lower than those of OPC treated LPC. It was found that the clinker was more effective than that of OPC in the treatment of LPC.
Get full access to this article
View all available purchase options and get full access to this article.
References
Ahnberg, H., S. E. Johansson, H. Pihl, and T. Carlsson. 2003. “Stabilizing effects of different binders in some Swedish soils.” Ground Improv. 7 (1): 9–23. https://doi.org/10.1680/grim.2003.7.1.9.
Aldieb, T. S., and H. G. Ibrahim. 2010. “Variation of feed chemical composition and its effect on clinker formation—Simulation process.” In Proc., World Congress on Engineering and Computer Science, 399–705. San Francisco, CA: International Association of Engineers.
Aniculăesi, M., A. Stanciu, and I. Lungu. 2011. “Behavior of expansive soils treated with eco-cement.” Buletin Politechnic Inst. Jassy Constr. Archit. 2 (1): 9–20.
ASTM. 2000. Standard test methods for laboratory compaction characteristics of soil using standard effort (12,400 ft-lbf / ft3 (600 kN-m / m3)). ASTM D698-00a. West Conshohocken, PA: ASTM.
ASTM. 2002a. Standard practice for classification of soils for engineering purposes (unified soil classification system). ASTM D2487-00. West Conshohocken, PA: ASTM.
ASTM. 2002b. Standard test method for particle-size analysis of soils. ASTM D422-63. West Conshohocken, PA: ASTM.
ASTM. 2002c. Standard test method for the specific gravity of soil solids by water pycnometer. ASTM D854-02. West Conshohocken, PA: ASTM.
ASTM. 2008. Standard test methods for one-dimensional swell or collapse of cohesive soils. ASTM D4546-08. West Conshohocken, PA: ASTM.
ASTM. 2010. Standard test methods for the liquid limit, plastic limit, and plasticity index of soils. ASTM D4318-10e1. West Conshohocken, PA: ASTM.
ASTM. 2011. Standard test methods for one-dimensional consolidation properties of soils using incremental loading. ASTM D2435-11. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard test method for unconsolidated-undrained triaxial compression test on cohesive soils. ASTM D2850-15. West Conshohocken, PA: ASTM.
Bahar, R., M. Benazzoug, and S. Kenai. 2004. “Performance of compacted cement-stabilized soil.” Cem. Concr. Compos. 26 (7): 811–820. https://doi.org/10.1016/j.cemconcomp.2004.01.003.
Balasubramaniam, A. S., A. H. M. Kamruzzaman, K. Uddin, D. G. Lin, N. Phienwij, and D. T. Bergado. 1998. “Chemical stabilization of Bangkok clay with cement, lime and fly ash additives.” In Vol. 2 of Proc., 13th Southeast Asian Geotechnical Conf., edited by Z. C. Moh, 253–258. Thailand: Southeast Asian Geotechnical Society.
Bell, F. G. 1993. Engineering treatment of soils. London, UK: Chapman & Hall.
Bell, F. G. 2004. Engineering geology and construction. London, UK: Spon Press.
Bergado, D. T., L. R. Anderson, N. Miura, and A. S. Balasubramaniam. 1996. Soft ground improvement in lowland and other environments. New York, NY: ASCE.
Bhattacharja, S., and J. Bhatty. 2003. Comparative performance of portland cement and lime in the stabilization of moderate to high plasticity clay soils. Skokie, IL: Portland Cement Association.
Brandl, H. 1981. “Alteration of soil parameters by stabilization with lime.” In Proc., 10th Int. Conf. on Soil Mechanics and Foundation Engineering, 587–594. Stockholm, Sweden: Swedish National Road and Transport Research Institute.
Chew, S. H., A. H. M. Kamruzzaman, and F. H. Lee. 2004. “Physicochemical and engineering behavior of cement treated clays.” J. Geotech. Geoenviron. Eng. 130 (7): 696–706. https://doi.org/10.1061/(ASCE)1090-0241(2004)130:7(696).
Chew, S. H., F. H. Lee, and Y. Lee. 1997. “Jet grouting in Singapore marine clay.” In Proc., 3rd Asian Young Geotechnology Engineering Conf., 231–238. Singapore: National Univ. of Singapore.
Cokca, E. 2001. “Use of class C fly ashes for the stabilization of an expansive soil.” J. Geotech. Geoenviron. Eng. 127 (7): 568–573. https://doi.org/10.1061/(ASCE)1090-0241(2001)127:7(568).
Cong, M., C. Longzhu, and C. Bing. 2014. “Analysis of strength development in soft clay stabilized with cement-based stabilizer.” Constr. Build. Mater. 71: 354–362. https://doi.org/10.1016/j.conbuildmat.2014.08.087.
Das, B. M., and N. Sivakugan. 2015. Foundation of geotechnical engineering. Boston, MA: Cengage Learning.
Di Sante, M., E. Fratalocchi, F. Mazzieri, and V. Brianzoni. 2015. “Influence of delayed compaction on the compressibility and hydraulic conductivity of soil-lime mixtures.” Eng. Geol. 185: 131–138. https://doi.org/10.1016/j.enggeo.2014.12.005.
Hago, A. W., A. A. Al-Rawas, and A. Al-Riyami. 2002. “Effect of varying cement content and curing conditions on the properties of sarooj (artificial pozzolana).” Build. Environ. 37 (1): 45–53. https://doi.org/10.1016/S0360-1323(00)00086-X.
Horpibulsuk, S., N. Miura, and T. S. Nagaraj. 2003. “Assessment of strength development in cement-admixed high water content clays with Abrams’ law as a basis.” Geotechnique 53 (4): 439–444. https://doi.org/10.1680/geot.2003.53.4.439.
Horpibulsuk, S., R. Rachan, A. Chinkulkijniwat, Y. Raksachon, and A. Suddeepong. 2010. “Analysis of strength development in cement-stabilized silty clay from microstructural considerations.” Constr. Build. Mater. 24 (10): 2011–2021. https://doi.org/10.1016/j.conbuildmat.2010.03.011.
Horpibulsuk, S., A. Suddeepong, A. Chinkulkijniwat, and M. D. Liu. 2012. “Strength and compressibility of lightweight cemented clays.” Appl. Clay Sci. 69: 11–21. https://doi.org/10.1016/j.clay.2012.08.006.
Jahandari, S., S. Li, M. Saberian, and M. Shahsavarigoughari. 2017. “Experimental study of the effects of geogrids on elasticity modulus, brittleness, strength, and stress-strain behavior of lime stabilized kaolinitic clay.” GeoResJ 13: 49–58. https://doi.org/10.1016/j.grj.2017.02.001.
Kalantari, B., and A. Prasad. 2014. “A study of the effect of various curing techniques on the strength of stabilized peat.” Transp. Geotech. 1 (3): 119–128. https://doi.org/10.1016/j.trgeo.2014.06.002.
Kawasaki, T., A. Niina, S. Saitoh, Y. Suzuki, and Y. Honjo. 1981. “Deep mixing method using cement hardening agent.” In Proc., 10th Int. Conf. on Soil Mechanics and Foundation Engineering, 721–724. Stockholm, Sweden: Publications Committee of X. ICSMFE.
Locat, J., H. Trembley, and S. Leroueil. 1996. “Mechanical and hydraulic behavior of a soft inorganic clay treated with lime.” Can. Geotech. J. 33 (4): 654–669. https://doi.org/10.1139/t96-090-311.
Lorenzo, G. A., and D. T. Bergado. 2006. “Fundamental characteristics of cement admixed clay in deep mixing.” J. Mater. Civ. Eng. 18 (2): 161–174. https://doi.org/10.1061/(ASCE)0899-1561(2006)18:2(161).
Mitchell, J. K. 1981. “Soil improvement state of the art report.” In Proc., 10th Int. Conf. on Soil Mechanics and Foundation Engineering, 509–565. Stockholm, Sweden: Publications Committee of X. ICSMFE.
Miura, N., S. Horpibulsuk, and T. S. Nagaraj. 2001. “Engineering behavior of cement stabilized clay at high water content.” Soils Found. 41 (5): 33–45. https://doi.org/10.3208/sandf.41.5_33.
Modarres, A., and Y. M. Nosoudy. 2015. “Clay stabilization using coal waste and lime—Technical and environmental impacts.” Appl. Clay Sci. 116–117: 281–288. https://doi.org/10.1016/j.clay.2015.03.026.
Nagaraj, T. S., N. Miura, A. Yamadera, and P. Yaligar. 1997. “Strength assessment of the cement admixtures soft clays—Parametric study.” In Proc., Int. Conf. on Ground Improvement Techniques, 379–386. Singapore: CI-Premier.
Nelson, J. D., and R. D. Miller. 1992. Expansive soils: problems and practice in foundation and pavement engineering. New York, NY: Wiley.
Nicholson, P. 2014. Soil improvement and ground modification methods. Waltham, MA: Butterworth and Heinemann.
Porbaha, A., S. Shibuya, and T. Kishida. 2000. “State of the art in deep mixing technology. Part III: Geomaterial characterization.” Ground Improv. 4 (3): 91–110. https://doi.org/10.1680/grim.2000.4.3.91.
Prusinski, J. R., and S. Bhattacharja. 1999. “Effectiveness of portland cement and lime in stabilizing clay soils.” Transp. Res. Rec. 1652: 215–227. https://doi.org/10.3141/1652-28.
Richardson, D. N. 1994. “AASHTO layer coefficients for cement-stabilized soil bases.” J. Mater. Civ. Eng. 8 (2): 83–87. https://doi.org/10.1061/(ASCE)0899-1561(1996)8:2(83).
Saitoh, S. 1988. “Experimental study of engineering properties of cement improved ground by the deep mixing method.” Ph.D. thesis, Nibon Univ.
Saride, S., A. J. Puppala, and S. R. Chikyala. 2013. “Swell-shrink and strength behaviors of lime and cement stabilized expansive organic clays.” Appl. Clay Sci. 85: 39–45. https://doi.org/10.1016/j.clay.2013.09.008.
Sarkar, G., M. R. Islam, M. Alamgir, and M. Rokonuzzaman. 2012. “Study on the geotechnical properties of cement-based composite fine-grained soil.” Int. J. Adv. Struct. Geotech. Eng. 1 (2): 42–49.
Sasanian, S., and T. A. Newson. 2013. “Use of mercury intrusion porosimetry for microstructural investigation of reconstituted clays at high water contents.” Eng. Geol. 158: 15–22. https://doi.org/10.1016/j.enggeo.2013.03.002.
Sivapullaiah, P. V., A. Sridharan, and R. K. V. Bhaskar. 2000. “Role of amount and type of clay in the lime stabilization of soils.” Ground Improv. 4 (1): 37–45. https://doi.org/10.1680/grim.2000.4.1.37.
Tremblay, H., S. Leroueil, and J. Locat. 2001. “Mechanical improvement and vertical yield stress prediction of clayey soils from eastern Canada treated with lime or cement.” Can. Geotech. J. 38 (3): 567–579. https://doi.org/10.1139/t00-119.
Uddin, K., A. S. Balasubramaniam, and D. T. Bergado. 1997. “Engineering behavior of cement-treated Bangkok soft clay.” Geotech. Eng. J. 28 (1): 89–119.
Xiao, H., W. Wang, and S. H. Goh. 2017. “Effectiveness study for fly ash cement improved marine clay.” Constr. Build. Mater. 157: 1053–1064. https://doi.org/10.1016/j.conbuildmat.2017.09.070.
Yoobanpot, N., P. Jamsawang, and S. Horpibulsuk. 2017. “Strength behavior and microstructural characteristics of soft clay stabilized with cement kiln dust and fly ash residue.” Appl. Clay Sci. 141: 146–156. https://doi.org/10.1016/j.clay.2017.02.028.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Sep 18, 2017
Accepted: Feb 21, 2018
Published online: Jun 9, 2018
Published in print: Aug 1, 2018
Discussion open until: Nov 9, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.