Comparative Study of Alkali-Activated Natural Pozzolan and Fly Ash Mortars
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 6
Abstract
Owing to the considerable emission resulting from portland cement (PC) production, a great deal of research has been devoted to finding alternative binders, among which alkali-activated binders have shown promising potential. Fly ash and natural Pozzolan are two choices of the starting ingredients for alkali-activated mateials, with the latter having rarely been studied. The current study compares the flow, strength, and transport properties of natural Pozzolan– and fly ash–based alkali-activated mortars. To this end, various mortar mixtures were prepared using fly ash or natural Pozzolan as aluminosilicate source (precursor) and 2.5, 5, 7.5, 10, and 12.5 M sodium hydroxide solution as alkaline activator. Several experiments were conducted on produced mortars to evaluate their fresh and hardened properties including including flow, compressive and flexural strengths, elastic modulus, absorption and total void volume, and rapid chloride migration. These tests were also conducted on PC mortars to compare the performance of alkali-activated mortars to that of PC mortars. The results of this study revealed that natural Pozzolan can be activated and perform to the same level of fly ash. However, the activation rate was slower and the minimum level of alkaline concentration for a proper activation was higher for natural Pozzolan than fly ash. While alkali-activated mortars displayed noticeably lower compressive strength than PC mortars, the studied mortars activated with sodium hydroxide molarities of 7.5–12.5 M produced strength adequate for structural applications. The transport properties of alkali-activated mortars having high NaOH molarity were similar to those of PC mortars.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASTM. (1999). “Standard practice for mechanical mixing of hydraulic cement pastes and mortars of plastic consistency.” ASTM C305, West Conshohocken, PA.
ASTM. (2001). “Standard test method for flow of hydraulic cement mortar.” ASTM C1437, West Conshohocken, PA.
ASTM. (2002a). “Standard test method for compressive strength of hydraulic cement mortars.” ASTM C109, West Conshohocken, PA.
ASTM. (2002b). “Standard test method for flexural strength of concrete (using simple beam with third-point loading).” ASTM C78, West Conshohocken, PA.
ASTM. (2012). “Standard specification for coal fly ash and raw or calcined natural Pozzolan for use in concrete.” ASTM C618, West Conshohocken, PA.
ASTM. (2013a). “Standard test method for density, absorption, and voids in hardened concrete.” ASTM C642, West Conshohocken, PA.
ASTM. (2013b). “Standard test methods for sampling and testing fly ash or natural Pozzolans for use in portland-cement concrete.” ASTM C311, West Conshohocken, PA.
Bondar, D., Lynsdale, C. J., Milestone, N. B., and Hassani, N. (2012). “Oxygen and chloride permeability of alkali-activated natural Pozzolan concrete.” ACI Mater. J., 109(1), 53–62.
Bondar, D., Lynsdale, C. J., Milestone, N. B., Hassani, N., and Ramezanianpour, A. A. (2011a). “Effect of type, form, and dosage of activators on strength of alkali-activated natural pozzolans.” Cem. Concr. Compos., 33(2), 251–260.
Bondar, D., Lynsdale, C. J., Milestone, N. B., Hassani, N., and Ramezanianpour, A. A. (2011b). “Engineering properties of alkali-activated natural Pozzolan concrete.” ACI Mater. J., 108(1), 64–72.
Chi, M., and Huang, R. (2013). “Binding mechanism and properties of alkali-activated fly ash/slag mortars.” Constr. Build. Mater., 40(Mar), 291–298.
Chubb, C. (2017). “Volcanoes of the World Map: Volcano Finder.” ⟨https://www.cccarto.com/volcano/#2/30.8/-6.3⟩ (Nov. 5, 2016).
Duxson, P., Fernandez-Jimenez, A., Provis, J. L., Lukey, G. C., Palomo, A., and van Deventer, J. S. J. (2007). “Geopolymer technology: The current state of the art.” J. Mater. Sci., 42(9), 2917–2933.
Fernandez-Jimenez, A., Palomo, A., and Alonso, M. M. (2005). “Alkali activation of fly ashes: Mechanisms of reaction.” Proc., Congress of Non-Traditional Cement and Concrete II, V. Bilek and Z. Kersner, eds., Brno Univ. of Technologie, Brno, Czech Republic, 1–12.
Fernandez-Jimenez, A., Palomo, A., and Lopez-Hombrados, C. (2006). “Engineering properties of alkali-activated fly ash concrete.” ACI Mater. J., 103(2), 106–112.
Ghafoori, N., Najimi, M., and Radke, B. (2016a). “Natural Pozzolan-based geopolymers for sustainable construction.” Environ. Earth Sci., 75(14), 1110.
Ghafoori, N., Sierra, K., Najimi, M., and Sharbaf, M. R. (2016b). “Properties of alkali-activated fly ash mortars made with multiple activators.” Proc., 2nd Int. Conf. on Concrete Sustainability, Madrid, Spain, 1330–1340.
Glukhovsky, V. (1994). “Ancient, modern and future concretes.” Proc., 1st Int. Conf. Alkaline Cements and Concretes, Krivenko, P. V., ed., Vol. 1, VIPOL Stock Company, Kiev, Ukraine, 1–8.
Haddad, R. H., and Alshbuol, O. (2016). “Production of geopolymer concrete using natural Pozzolan: A parametric study.” Constr. Build. Mater., 114, 699–707.
Huntzinger, D. N., and Eatmon, T. D. (2009). “A life-cycle assessment of portland cement manufacturing: Comparing the traditional process with alternative technologies.” J. Clean. Prod., 17(7), 668–675.
Ismail, I., Bernal, S. A., Provis, J. L., Nicolas, R. S., Hamdan, S., and van Deventer, J. S. J. (2014). “Modification of phase evolution in alkali-activated blast furnace slag by the incorporation of fly ash.” Cem. Concr. Compos., 45(Jan), 125–135.
Khale, D., and Chaudhary, R. (2007). “Mechanism of geopolymerization and factors influencing its development: A review.” J. Mater. Sci., 42(3), 729–746.
Lemougna, P. N, MacKenzie, K. J. D., and Melo, U. F. C. (2011). “Synthesis and thermal properties of inorganic polymers (geopolymers) for structural and refractory applications from volcanic ash.” Ceram. Int., 37(8), 3011–3018.
Lorenz, W. (1985). “The use of volcanic rocks as construction raw material.” Nat. Resour. Develop., 22, 7–24.
Ma, Y., Hua, J., and Ye, G. (2013). “The pore structure and permeability of alkali-activated fly ash.” Fuel, 104(Feb), 771–780.
NORDTEST. (1999). “Concrete, mortar and cement-based repair materials: Chloride migration coefficient from non-steady-state migration experiments.”, Espoo, Finland.
Pacheco-Torgal, F., Abdollahnejad, Z., Camões, A. F., Jamshidi, M., and Ding, Y. (2012). “Durability of alkali-activated binders: A clear advantage over portland cement or an un-proven issue?” Constr. Build. Mater., 30(May), 400–405.
Pacheco-Torgal, F., Castro-Gomes, J., and Jalali, S. (2008). “Alkali-activated binders. A review: Part 1: Historical background, terminology, reaction mechanisms and hydration products.” Constr. Build. Mater., 22(7), 1305–1314.
Pacheco-Torgal, F., Labrincha, J., Leonelli, C., Palomo, A., and Chindaprasit, P. (2015). Handbook of alkali-activated cements, mortars and concretes, Elsevier, Amsterdam, Netherlands.
Palomo, A., Fernadez-Jimenez, A., and Kovalchuk, G. (2005). “Some key factors affecting the alkali activation of fly ash.” Proc., 2nd Int. Symp. of Non-Traditional Cement and Concrete, Brno, Czech Republic.
Palomo, A., Grutzeck, M. W., and Blanco, M. T. (1999). “Alkali-activated fly ashes: A cement for the future.” Cem. Concr. Res., 29(8), 1323–1329.
Ravikumar, D., Peethamparan, S., and Neithalath, N. (2010). “Structure and strength of NaOH activated concretes containing fly ash or GGBS as the sole binder.” Cem. Concr. Compos., 32(6), 399–410.
Shi, C., Fernandez-Jimenez, A., and Palomo, A. (2011). “New cements for the 21st century: The pursuit of an alternative to portland cement.” Cem. Concr. Res., 41(7), 750–763.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 30 • Issue 6 • June 2018
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jul 31, 2017
Accepted: Dec 7, 2017
Published online: Apr 13, 2018
Published in print: Jun 1, 2018
Discussion open until: Sep 13, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.