Performance-Based Procedure for the Definition of Controlled Low-Strength Mixtures
Publication: Journal of Materials in Civil Engineering
Volume 27, Issue 11
Abstract
Controlled low-strength material (CLSM) is a self-consolidating cementitious material used as backfill in narrow trenches. The high content of aggregates and water in CLSM leads to a special behavior that is closer to soil than concrete. Consequently, mixture proportioning methodologies for conventional concrete do not apply to CLSM. The objective of this paper is to propose a new methodology to achieve the optimal composition that fulfills the flowability and compressive strength requirements of the material. Instead of computing the aggregate or the cement separately, all solid particles in the mixture are considered concurrently to estimate the water content in terms of water-to-solid ratio (W/S). In this way, the compressive strength can be modified without compromising the desired flowability. An example application is presented and an experimental program is conducted to validate this philosophy. The results confirm that the methodology proposed provides compositions that satisfy the main requirements of CLSM, thus representing a contribution to the use of more economical and adequate materials.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors thank the Gas Natural Fenosa company for its financial support and, in particular, for its active collaboration in the project. Likewise, the authors appreciate the comments of Jordi Roselló and Carlos Aranda. The first author acknowledges the grant PDJ provided Departament d’Universitats, Recerca i Societat de la Informació de la Generalitat de Catalunya.
References
Alizadeh, V., Helwany, S., Ghorbanpoor, A., and Sobolev, K. (2014). “Design and application of controlled low strength materials as a structural fill.” Constr. Build. Mater., 53, 425–431.
American Concrete Institute (ACI). (2005). “Controlled low-strength materials.”, ASTM International, Farmington Hills, MI.
ASTM. (2008). “Standard test methods for flow of hydraulic cement mortar.” C1437-07, West Conshohocken, PA.
Blanco, A., Pujadas, P., Cavalaro, S. H. P., and Aguado, A. (2014). “Methodology for the design of controlled low-strength materials. Application to the backfill of narrow trenches.” Constr. Build. Mater., 72, 23–30.
Bouzalakos, S., Dudeney, A. W. L., and Chan, B. K. C. (2013). “Formulating and optimising the compressive strength of controlled low-strength materials containing mine tailings by mixture design and response surface methods.” Miner. Eng., 53, 48–56.
BSI (British Standards Institution). (2005). “Methods of testing cement—Part 1: Determination of strength.” EN 196-1, London.
Etxeberria, M., Ainchil, J., Pérez, M. E., and González, A. (2013). “Use of recycled fine aggregates for control low strength materials (CLSMs) production.” Constr. Build. Mater., 44, 142–148.
Fennis, S. A. A. M., Walraven, J. C., and den Uijl, J. A. (2012). “Defined-performance design of ecological concrete.” Mater. Struct., 46(4), 639–650.
Fung, W. W. S., and Kwan, A. K. H. (2010). “Role of water film thickness in rheology of CSF mortar.” Cem. Concr. Compos., 32(4), 255–264.
Fung, W. W. S., Kwan, A. K. H., and Wong, H. H. C. (2008). “Wet packing of crushed rock fine aggregate.” Mater. Struct., 42(5), 631–643.
Klein, N. S. (2012). “El rol físico del agua en mezclas de cemento portland.” Ph.D. thesis, Polytechnic Univ. of Catalonia, Barcelona, Spain.
Klein, N. S., Bachmann, J., Aguado, A., and Toralles-Carbonari, B. (2012). “Evaluation of the wettability of mortar component granular materials through contact angle measurements.” Cem. Concr. Res., 42(12), 1611–1620.
Kwan, A. K. H., and Fung, W. W. S. (2009). “Packing density measurement and modelling of fine aggregate and mortar.” Cem. Concr. Compos., 31(6), 349–357.
Kwan, A. K. H., and Fung, W. W. S. (2012). “Roles of water film thickness and SP dosage in rheology and cohesiveness of mortar.” Cem. Concr. Compos., 34(2), 121–130.
Siddique, R. (2009). “Utilization of waste materials and by-products in producing controlled low-strength materials.” Resour. Conserv. Recycl., 54(1), 1–8.
Taha, R. A., Alnuaimi, A. S., Al-Jabri, K. S., and Al-Harthy, A. S. (2007). “Evaluation of controlled low strength materials containing industrial by-products.” Build. Environ., 42(9), 3366–3372.
Wong, H. H. C., and Kwan, A. K. H. (2007). “Packing density of cementitious materials: Part 1—Measurement using a wet packing method.” Mater. Struct., 41(4), 689–701.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Aug 21, 2014
Accepted: Jan 22, 2015
Published online: Mar 3, 2015
Discussion open until: Aug 3, 2015
Published in print: Nov 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.