Performance Evaluation of an Eco-Binder Made with Slag and CFBC Fly Ash
Publication: Journal of Materials in Civil Engineering
Volume 26, Issue 12
Abstract
Performance of the engineering properties of paste manufactured with an eco-binder was evaluated. The eco-binder without cement, SCA, was made with slag (S) and fly ash (CA) that had been created by circulating fluidized bed combustion (CFBC). Experimental results show that the pure slag paste hardly sets and the pure CA paste gives very little strength. But when slag and CA are mixed together, the SCA paste not only has proper setting times but also has sufficient strength. The compressive and tensile strength of SCA paste can reach 80 MPa and 4.6 MPa, respectively, at 28 days and higher at longer ages. In addition, the early expansion of the SCA paste compensates for its later shrinkage so that the ultimate drying shrinkage of SCA paste is lower than that of ordinary portland cement paste. The hydration products of the SCA paste detected by X-ray diffraction (XRD), scanning electron microscope (SEM), and energy-dispersive X-ray (EDX) are ettringite, calcium silicate hydrate (C-S-H), and calcium silicate alumina hydrate (C-S-A-H). All of them are bonded together and generate self-cementitious properties in SCA paste.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the financial support of this work by National Taiwan University of Science and Technology (Taiwan Tech) through scholarships.
References
ASTM. (1999). “Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens).” C109/C109M–99, West Conshohocken, PA.
ASTM. (2007). “Standard test methods for time of setting of hydraulic cement by vicat needle.” C191–07, West Conshohocken, PA.
ASTM. (2008a). “Standard specification for flow table for use in tests of hydraulic cement.” C230M, West Conshohocken, PA.
ASTM. (2008b). “Standard test method for measuring the drying shrinkage of masonry mortar.” C1148, West Conshohocken, PA.
Berry, M., Stephens, J., and Cross, D. (2011). “Performance of 100% fly ash concrete with recycled glass aggregate.” ACI Mater. J., 4(108), 378–384.
Chindaprasirt, P., Chareerat, T., Hatanaka, S., and Cao, T. (2011). “High-strength geopolymer using fine high-calcium fly ash.” J. Mater. Civ. Eng., 264–270.
Diaz-Loya, E. I., Allouche, E. N., and Vaidya, S. (2011). “Mechanical properties of fly-ash-based geopolymer concrete.” ACI Mater. J., 108(3), 300–307.
Dongxu, L., Xuequan, W., Jinlin, S., and Yujiang, W. (2000). “The influence of compound admixtures on the properties of high-content slag cement.” Cem. Concr. Res., 30(1), 45–50.
Ghafoori, N., and Mora, C. A. G. (1998). “Compacted non-cement concrete utilizing fluidized bed and pulverized coal combustion by-products.” ACI Mater. J., 95(5), 582–592.
Guo Li, X., Bin Chen, Q., Zhong Huang, K., Guo Ma, B., and Wu, B. (2012). “Cementitious properties and hydration mechanism of circulating fluidized bed combustion (CFBC) desulfurization ashes.” Constr. Build. Mater., 36, 182–187.
He, J., Zhang, G., Hou, S., and Cai, C. (2011). “Geopolymer-based smart adhesives for infrastructure health monitoring: Concept and feasibility.” J. Mater. Civ. Eng., 100–109.
Iribarne, J., Iribarne, A., Blondin, J., and Anthony, E. J. (2001). “Hydration of combustion ashes—A chemical and physical study.” Fuel, 80(6), 773–784.
Li, Z., Zhang, Y., and Zhou, X. (2005). “Short fiber reinforced geopolymer composites manufactured by extrusion.” J. Mater. Civ. Eng., 624–631.
Marks, M., Jóźwiak-Niedźwiedzka, D., Glinicki, M., Olek, J., and Marks, M. (2012). “Assessment of scaling durability of concrete with CFBC ash by automatic classification rules.” J. Mater. Civ. Eng., 860–867.
Odler, I., and Colán-Subauste, J. (1999). “Investigations on cement expansion associated with ettringite formation.” Cem. Concr. Res., 29(5), 731–735.
Palacios, M., and Puertas, F. (2011). “Effectiveness of mixing time on hardened properties of waterglass-activated slag pastes and mortars.” ACI Mater. J., 108(1), 73–78.
Palomo, A., Grutzeck, M. W., and Blanco, M. T. (1999). “Alkali-activated fly ashes: A cement for the future.” Cem. Concr. Res., 29(8), 1323–1329.
Reddy, D., Edouard, J., and Sobhan, K. (2013). “Durability of fly ash–based geopolymer structural concrete in the marine environment.” J. Mater. Civ. Eng., 781–787.
Rust, D., Rathbone, R., Mahboub, K., and Robl, T. (2012). “Formulating low-energy cement products.” J. Mater. Civ. Eng., 1125–1131.
Sheng, G., Li, Q., and Zhai, J. (2012). “Investigation on the hydration of CFBC fly ash.” Fuel, 98, 61–66.
Sheng, G., Li, Q., Zhai, J., and Li, F. (2007). “Self-cementitious properties of fly ashes from CFBC boilers co-firing coal and high-sulphur petroleum coke.” Cem. Concr. Res., 37(6), 871–876.
Shon, C.-S., Mukhopadhyay, A. K., Saylak, D., Zollinger, D. G., and Mejeoumov, G. G. (2010). “Potential use of stockpiled circulating fluidized bed combustion ashes in controlled low strength material (CLSM) mixture.” Constr. Build. Mater., 24(5), 839–847.
Taylor, H. F. W. (1993). “Nanostructure of C-S-H: Current status.” Adv. Cem. Based Mater., 1(1), 38–46.
Wang, J., Wu, Y., and Anthony, E. J. (2005). “The hydration behavior of partially sulfated fluidized bed combustor sorbent.” Ind. Eng. Chem. Res., 44(22), 8199–8204.
Yang, K.-H., Song, J.-K., and Song, K.-I. (2013). “Assessment of reduction of alkali-activated concrete.” J. Cleaner Prod., 39, 265–272.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jun 13, 2013
Accepted: Jan 3, 2014
Published online: Jan 6, 2014
Discussion open until: Nov 26, 2014
Published in print: Dec 1, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.