Modeling Viscoelastic Behavior of Polyethylene Pipe Stresses
Publication: Journal of Materials in Civil Engineering
Volume 26, Issue 4
Abstract
Polyethylene pipes are commonly used for new and existing pipeline systems. The stresses developed in the polyethylene pipes affect the behavior of other pipe materials in the system to which they are connected. The overall behavior of the pipeline depends on the soil-pipe interaction characteristics; however, understanding and modeling the polyethylene pipe stresses as a first step without the influence of other factors is necessary. Laboratory tests were performed to investigate the time-dependent stress relaxation behavior of polyethylene pipe under mechanical and thermal loading conditions. Analytical methods using convolution integrals and numerical modeling using finite elements were used to model stress relaxation behavior monitored during the tests performed. The results show that the pipe thermal stresses are significantly less than the design stresses typically used by utility companies. In addition, linearly viscoelastic material characterization can be used to predict polyethylene pipe behavior for the range of stresses expected to occur in buried polyethylene pipes exposed to thermal loading. This article presents the test results as well as analytical and numerical results for modeling and predicting stresses in polyethylene pipes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writer would like to thank Professors Harry E. Stewart and Thomas D. O’Rourke, and Mr. Timothy K. Bond at Cornell University for their help and input during the research.
References
ABAQUS 5.8 [Computer software] (1999). Pawtucket, RI, Hibbitt, Karlsson, and Sorenson.
American Gas Association. (1994). Plastic pipe manual for gas service, Arlington, VA.
Bilgin, Ö. (1999). “Improved design and construction practices for thermal loads in plastic gas pipelines.” Ph.D. dissertation, Cornell Univ., Ithaca, NY.
Bilgin, Ö., and Stewart, H. E. (2001). “Designing plastic pipelines for thermal loads.” Proc., ASCE Pipelines 2001—Advances in Pipeline Engineering & Construction Conf. (CD-ROM), ASCE, Reston, VA.
Bilgin, Ö, Stewart, H. E., and O’Rourke, T. D. (2007). “Thermal and mechanical properties of polyethylene pipes.” J. Mater. Civ. Eng., 1043–1052.
Catsiff, E., and Tobolsky, A. V. (1955). “Stress-relaxation of polyisobutylene in the transition region.” J. Colloid Sci., 10(4), 375–392.
Catsiff, E., and Tobolsky, A. V. (1956). “Elastoviscous properties of polyisobutylene (and other amorphous polymers) from stress-relaxation studies. IX. A summary of results.” J. Polym. Sci., 19(91), 111–121.
Chua, K. M., and Lytton, R. L. (1989). “Viscoelastic approach to modeling performance of buried pipes.” J. Transp. Eng., 253–269.
Husted, J. L., and Thompson, D. M. (1985). Pull-out forces on joints in polyethylene pipe systems, A guideline for gas distribution engineering, E.I. Du Pont de Nemours.
Janson, L.-E. (1985). “Investigation of the long-term creep modulus for buried polyethylene pipes subjected to constant deflection.” Proc., Advances in Underground Pipeline Engineering, J. K. Jeyapalan, ed., Pipeline Division of the ASCE, Univ. of Wisconsin-Madison, Madison, WI, 253–262.
Moore, I. D. (1994). “Three dimensional time dependent model for buried hdpe pipe.” Proc., 8th Int. Conf. on Computer Methods and Advances in Geomechanics, H. J. Siriwardane, ed., A.A. Balkema, The Netherlands.
Moore, I. D., and Hu, F. (1995). “Response of profiled high-density polyethylene pipe in hoop compression.” Transportation Research Record 1514, Transportation Research Board, Washington, DC, 29–36.
Moore, I. D., and Zhang, C. (1995). “Computer models for predicting hdpe pipe stiffness.” Proc., Annual Conf., Canadian Society for Civil Engineering, Ottawa, ON, Canada, 565–574.
Office of Federal Register. (2006). “Transportation of natural and other gas by pipeline: Minimum federal safety standards.” Code of Federal Regulations, title 49, Part 192, General Services Administration, National Archives and Records Service, Washington, DC.
Phillips Driscopipe, Inc. (1981). Driscopipe 8000, the super tough polyethylene piping system for gas distribution, Richardson, TX.
Popelar, C. F., Popelar, C. H., and Kenner, V. H. (1990). “Viscoelastic material characterization and modeling for polyethylene.” Polym. Eng. Sci., 30(10), 577–586.
Popelar, C. H., and Evans, D. (2004). “Creep ovalization and buckling of a linear viscoelastic externally pressurized pipe.” J. Pressure Vessel Technol., 126(2), 208–215.
Popelar, C. H., Kenner, V. H., and Wooster, J. P. (1991). “An accelerated method for establishing the long term performance of polyethylene gas pipe materials.” Polym. Eng. Sci., 31(24), 1693–1700.
Stewart, H. E., Bilgin, Ö., O’Rourke, T. D., and Keeney, T. M.-J. (1999). “Technical reference for improved design and construction practices to account for thermal loads in plastic gas pipelines.”, Gas Research Institute, Chicago.
Tobolsky, A. V. (1960). Properties and structure of polymers, Wiley, New York.
Williams, M. L., Landel, R. F., and Ferry, J. D. (1955). “The temperature dependence of relaxation mechanism in amorphous polymers and other glass-forming liquids.” J. Am. Chem. Soc., 77(14), 3701–3707.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Oct 15, 2012
Accepted: May 28, 2013
Published online: May 30, 2013
Discussion open until: Oct 30, 2013
Published in print: Apr 1, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.