Mechanistic Modeling of Fracture in Asphalt Mixtures under Compressive Loading
Publication: Journal of Materials in Civil Engineering
Volume 25, Issue 9
Abstract
When an asphalt mixture is subjected to a destructive compressive load, it experiences a sequence of three deformation stages, as follows: the (1) primary, (2) secondary, and (3) tertiary stages. Most literature research focuses on plastic deformation in the primary and secondary stages, such as prediction of the flow number, which is in fact the initiation of the tertiary stage. However, little research effort has been reported on the mechanistic modeling of the damage that occurs in the tertiary stage. The main objective of this paper is to provide a mechanistic characterizing method for the damage modeling of asphalt mixtures in the tertiary stage. The preliminary study conducted by the writers illustrates that deformation during the tertiary flow of the asphalt mixtures is principally caused by the formation and propagation of cracks, which was signaled by the increase of the phase angle in the tertiary phase. The strain caused by the growth of cracks is the viscofracture strain, which can be obtained by conducting the strain decomposition of the measured total strain in the destructive compressive test. The viscofracture strain is employed in the research reported in this paper to mechanistically characterize the time-dependent fracture (viscofracture) of asphalt mixtures in compression. By using the dissipated pseudostrain energy-balance principle, the damage density and true stress are determined and both are demonstrated to increase with load cycles in the tertiary stage. The increased true stress yields extra viscoplastic strain, which is the reason why the permanent deformation is accelerated by the occurrence of cracks. To characterize the evolution of the viscofracture in the asphalt mixtures in compression, a pseudo J-integral Paris’ law in terms of damage density is proposed and the material constants in the Paris’ law are determined, which can be employed to predict the fracture of asphalt mixtures in compression.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers acknowledge the financial support of the Federal Highway Administration to the Asphalt Research Consortium (ARC).
References
Arambula, E., Masad, E., and Martin, A. E. (2007). “Moisture susceptibility of asphalt mixtures with known field performance: Evaluated with dynamic analysis and crack growth model.” Transportation Research Record 2001, Transportation Research Board, Washington, DC, 20–28.
Bausano, J., and Williams, R. C. (2010). “Energy-based approach for determining flow number.” J. Test. Eval., 38(1), 1–8.
Biligiri, K. P., Kaloush, K. E., Mamlouk, M. S., and Witczak, M. W. (2007). “Rational modeling of tertiary flow for asphalt mixtures.” Transportation Research Record 2001, Transportation Research Board, Washington, DC, 63–72.
Castelo Branco, V. T. F., Masad, E., Bhasin, A., and Little, D. N. (2008). “Fatigue analysis of asphalt mixtures independent of mode of loading.” Transportation Research Record 2057, Transportation Research Board, Washington, DC, 149–156.
Cleveland, G. S., Lytton, R. L., and Button, J. W. (2003). “Using pseudostrain damage theory to characterize reinforcing benefits of geosynthetic materials in asphalt concrete overlays.” Transportation Research Record 1849, Transportation Research Board, Washington, DC, 202–211.
Findley, W. N., Lai, J. S., and Onaran, K. (1989). Creep and relaxation of nonlinear viscoelastic materials with an introduction to linear viscoelasticity, Dover Publications, Mineola, NY.
Gibson, N. H., Schwartz, C. W., Schapery, R. A., and Witczak, M. W. (2003). “Viscoelastic, viscoplastic, and damage modeling of asphalt concrete in unconfined compression.” Transportation Research Record 1860, Transportation Research Board, Washington, DC, 3–15.
Goh, S. W., and You, Z. (2009). “A simple stepwise method to determine and evaluate the initiation of tertiary flow for asphalt mixtures under dynamic creep test.” Constr. Build. Mater., 23(11), 3398–3405.
Jones, R. D. (1993). “SHRP materials reference library: Asphalt cements: A concise data compilation.”, National Research Council, Washington, DC.
Kachanov, L. M. (1986). Introduction to continuum damage mechanics, Martinus Nijhoff, Dordrecht, Netherlands.
Kaloush, K. E., et al. (2002). “Tertiary flow characteristics of asphalt mixtures.” Proc., Asphalt Paving Technology, Association of Asphalt Paving Technologists, Lino Lakes, MN, 248–280.
Kim, Y. R., Lee, Y. C., and Lee, H. J. (1995). “Correspondence principle for characterization of asphalt concrete.” J. Mater. Civ. Eng., 7(1), 59–68.
Kvasnak, A., Robinette, C. J., and Williams, R. C. (2007). “Statistical development of a flow number predictive equation for the mechanistic-empirical pavement design guide.” Transportation Research Board 86th Annual Meeting, Paper No. 07-1000, Transportation Research Board, National Research Council, Washington, DC.
Lemaitre, J., and Desmorat, R. (2005). Engineering damage mechanics: Ductile, creep, fatigue and brittle failures, Springer, New York.
Levenberg, E., and Uzan, J. (2004). “Triaxial small-strain viscoelastic-viscoplastic modeling of asphalt aggregate mixes.” Mech. Time-Depend. Mater., 8(4), 365–384.
Lytton, R. L. (2000). “Characterizing asphalt pavements for performance.” Transportation Research Record 1723, Transportation Research Board, Washington, DC, 5–16.
Masad, E., Branco, V. T. F. C., Little, D. N., and Lytton, R. L. (2008). “A unified method for the analysis of controlled-strain and controlled-stress fatigue testing.” Int. J. Pav. Eng., 9(4), 233–246.
Park, S. W., Kim, Y. R., and Schapery, R. A. (1996). “Viscoelastic continuum damage model and its application to uniaxial behavior of asphalt concrete.” Mech. Mater., 24(4), 241–255.
Ramsamooj, D. V., and Ramadan, J. (1999). “Prediction of permanent deformation of asphalt concrete in cyclic and monotonic loading.” J. Test. Eval., 27(5), 320–326.
Rodezno, M. C., Kaloush, K. E., and Corrigan, M. R. (2010). “Development of a flow number predictive model.” Transportation Research Record 2181, Transportation Research Board, Washington, DC, 79–87.
Schapery, R. A. (1975). “Theory of crack initiation and growth in viscoelastic media–II. Approximate methods of analysis.” Int. J. Fract., 11(3), 369–388.
Schapery, R. A. (1984). “Correspondence principles and a generalized J-integral for large deformation and fracture analysis of viscoelastic media.” Int. J. Fract., 25(3), 195–223.
Si, Z., Little, D. N., and Lytton, R. L. (2002). “Characterization of microdamage and healing of asphalt concrete mixtures.” J. Mater. Civ. Eng., 14(6), 461–470.
Sullivan, R. (2008). “Development of a viscoelastic continuum damage model for cyclic loading.” Mech. Time-Depend. Mater., 12(4), 329–342.
Tseng, K. H., and Lytton, R. L. (1989). “Prediction of permanent deformation in flexible pavement materials.” Implication of aggregates in the design, construction, and performance of flexible pavements, H. G. Schreuders and C. R. Marek, eds., ASTM, Philadelphia, 154–172.
Texas DOT (TXDOT). (2004). “Standard specifications for construction and maintenance of highways, streets, and bridges.” Rep. Prepared for the Texas DOT, Austin, TX.
Texas DOT (TXDOT). (2008). “Test procedure for design of bituminous mixtures.”, Austin, TX.
Walubita, L. F., Martin, A. E., Cleveland, G. S., and Lytton, R. L. (2006). “Computation of pseudo strain energy and Paris law fracture coefficients from surface energy and uniaxial strain-controlled tension test data.” Int. J. Pav. Eng., 7(3), 167–178.
Wen, H., and Bahia, H. (2009). “Characterizing fatigue of asphalt binders with viscoelastic continuum damage mechanics.” Transportation Research Record 2126, Transportation Research Board, Washington, DC, 55–62.
Wineman, A. S., and Rajagopal, K. R. (2001). Mechanical response of polymers: An introduction, Cambridge University Press, Cambridge, UK.
Witczak, M. W., Kaloush, K., Pellinen, T., and El-Basyouny, M. (2002). “Simple performance test for superpave mix design.”, Transportation Research Board, Washington, DC.
Zhang, Y., Luo, R., and Lytton, R. L. (2012). “Characterizing permanent deformation and fracture of asphalt mixtures by using compressive dynamic modulus tests.” J. Mater. Civ. Eng., 24(7), 898–906.
Zhou, F., and Scullion, T. (2002). “Discussion: Three stages of permanent deformation curve and rutting model.” Int. J. Pav. Eng., 3(4), 251–260.
Zhou, F., Scullion, T., and Sun, L. (2004). “Verification and modeling of three-stage permanent deformation behavior of asphalt mixes.” J. Transp. Eng., 130(4), 486–494.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Mar 8, 2012
Accepted: Aug 23, 2012
Published online: Aug 30, 2012
Discussion open until: Jan 30, 2013
Published in print: Sep 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.