Utilization of Foaming Technology in Warm-Mix-Asphalt Mixtures Containing Moist Aggregates
Publication: Journal of Materials in Civil Engineering
Volume 23, Issue 9
Abstract
The objective of this study was to conduct a laboratory investigation of moisture susceptibility and rutting resistance of warm-mix asphalt (WMA) mixtures containing moist aggregates by using a foaming technology. Gyration number of various samples, indirect tensile strength (ITS), tensile strength ratio, rut depths of dry and conditioned specimens, and deformation (flow) were measured for all mixtures. The experimental design included two aggregate moisture contents (0 and by weight of the dry mass of the aggregate), two lime contents (1% and 2% lime by weight of dry aggregate), one liquid antistripping agent (ASA) and non-ASA, three foaming water contents (2, 3, and 4%) with control, and two aggregate sources. A total of 42 mixtures were used and 420 specimens were tested in this study. The test results indicated that the aggregate source significantly affects the ITS and rutting resistance regardless of the foaming water content, ASA, and aggregate moisture content. In addition, the ITS and rut depth of some foamed mixtures containing moist aggregate satisfies the demand of pavement performance without additional treatment, although some mixtures need a completely dry aggregate or additional treatments. The mixture with various hydrated lime contents exhibited similar rutting and moisture resistance under dry and wet conditions. The liquid ASA used in this study is not recommended for use in foaming WMA mixtures with moist aggregates, because it is sensitive to moisture.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support was made through a grant from South Carolina’s Department of Transportation (SCDOT) and the Asphalt Rubber Technology Service (ARTS) of Clemson University.
References
AASHTO. (2007). “Standard method of test for resistance of compacted asphalt mixtures to moisture-induced damage.” T283, Washington, DC.
AASHTO. (2009). “Standard method of test for determining the rutting susceptibility of hot mix asphalt using the asphalt pavement analyzer (APA).” TP63-09, Washington, DC.
Christensen, W. D., Bonaquist, R., and Jack, D. P. (2000). “Evaluation of triaxial strength as a simple test for asphalt concrete rut resistance.” Final Rep. Prepared for Pennsylvania Dept. of Transportation, PENNDOT, Harrisburg, PA.
D’Angelo, J., et al. (2008). “Warm mix asphalt: European practice.” Publication FHWA-PL-08-007, FHWA, U.S. Dept. of Transportation, Washington, DC.
Diefenderfer, S. D., McGhee, K. K., and Donaldson, B. M. (2007). “Installation of warm mix asphalt projects in Virginia.” FHWA/VTRC 07-R25, Virginia Dept. of Transportation, Richmond, VA.
Gandhi, T. (2008). “Effects of warm asphalt additives on asphalt binder and mixture properties.” Ph.D. dissertation, Clemson Univ., Clemson, SC.
Hurley, C., and Prowell, B. (2006). Evaluation of potential processes for use in warm mix asphalt, Vol. 75, AAPT, College Park, MD, 41–90.
Hodo, W., Kvasnak, A., and Brown, E. R. (2009). “Investigation of foamed asphalt (warm mix asphalt) with high reclaimed asphalt pavement (RAP) content for sustainment and rehabilitation of asphalt pavement.” TRB 88th Annual Meeting, Transportation Research Board, Washington, DC.
Jenkins, K. J., de Groot, J. L. A., van de Ven, M. F. C., and Molenaar, A. A. A. (1999). “Half-warm foamed bitumen treatment, a new process.” 7th Conf. on Asphalt Pavements for Southern Africa, National Asphalt Pavement Association, Lanham, MD.
Kristjansdottir, O., Muench, S, Michael, L., and Burke, G. (2007). “Assessing potential for warm-mix asphalt technology adoption.” Transp. Res. Rec., 2040, 91–99.
Larsen, O. R., Moen, Ø., Robertus, C., and Koenders, B. G. (2004). “WAM-foam asphalt production at lower operating temperatures as an environmental friendly alternative to HMA.” 3rd Eurasphalt and Eurobitume Congress, Foundation Eurasphalt, Breukelen, Netherlands.
Middleton, B., and Forfylow, R. W. (2009). “Evaluation of warm-mix asphalt produced with the double barrel green process.” Transp. Res. Rec., 2126, 19–26.
Mogawer, W., Austerman, A., and Bonaquist, R. (2009). “Evaluating effects of warm-mix asphalt technology additive dosages on workability and durability of asphalt mixtures containing recycled asphalt pavement.” TRB 88th Annual Meeting, Transportation Research Board, Washington, DC.
Prowell, B. D., and Hurley, G. C. (2007). “Warm-mix asphalt: Best practices.” National Asphalt Pavement Association, Lanham, MD.
Tao, M., and Mallick, R. (2009). “Evaluation of effects of warm-mix asphalt additives on properties of reclaimed asphalt pavement material.” Transp. Res. Rec., 2126, 151–160.
Wayne, H. (2009). “Field and laboratory investigation of foamed asphalt (warm-mix asphalt) with high recycled asphalt pavement content for sustainment and rehabilitation of asphalt pavement.” TRB 88th Annual Meeting, Transportation Research Board, Washington, DC.
Wielinski, J., Hand, A., and Rausch, D. M. (2009). “Laboratory and field evaluations of foamed warm-mix asphalt projects.” Transp. Res. Rec., 2126, 125–131.
Xiao, F., Jordan, J., and Amirkhanian, S. (2009). “Laboratory investigation of moisture damage in warm-mix asphalt containing moist aggregate.” Transp. Res. Rec., 2126, 115–124.
Xiao, F., and Amirkhanian, S. N. (2010). “Effects of liquid antistrip additives on rheology and moisture susceptibility of water bearing warm mixtures.” Constr. Build. Mater., 24(9), 1649–1655.
Xiao, F., Amirkhanian, S., and Putman, B. (2010a). “Evaluation of rutting resistance in warm mix asphalts containing moist aggregate.” Transp. Res. Rec., 2180, 75–84.
Xiao, F., Zhao, W., Gandhi, T., and Amirkhanian, S. N. (2010b), “Influence of anti-stripping additive on moisture susceptibility of warm mix asphalt mixture.” J. Mater. Civ. Eng., 22(10), 1047–1055.
Zaniewski, J. P., and Srinivasan, G. (2004). Evaluation of indirect tensile strength to identify asphalt concrete rutting potential, Asphalt Technology Program, Dept. of Civil and Environmental Engineering, West Virginia Univ., Morgantown, WV.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Oct 14, 2010
Accepted: Feb 16, 2011
Published online: Feb 18, 2011
Published in print: Sep 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.