Discrete Element Modeling of Constant Strain Rate Compression Tests on Idealized Asphalt Mixture
Publication: Journal of Materials in Civil Engineering
Volume 23, Issue 1
Abstract
Discrete element modeling has been used to simulate constant strain rate compressive tests for an idealized asphalt mixture comprising approximately single-sized sand particles. A range of constant strain-rate compressive tests to failure have been undertaken in the laboratory and the axial stress-strain response has been carefully measured. The peak stress (compressive strength) of the material was found to be as a power-law function of the equivalent (temperature compensated) strain rate in the viscoelastic region of behavior. The internal geometry of the idealized asphalt mixture has been reproduced in PFC-3D and internal damage (cracking) in the material was modeled by allowing bond breakage between adjacent particles. Elastic contact properties have been used to investigate the effect of random variations in internal sample geometry, the distribution of bond strengths between adjacent particles and the coefficient of friction between particles where the bond has broken. A simple viscoelastic Burger’s model was used to introduce time dependent shear and normal (tensile) contact stiffnesses and an elastic contact has been assumed for the compressive normal contact stiffness. To reduce the computation time, both viscosities in the Burger’s model were scaled which has been shown to have the same effect as scaling the loading velocity (strain rate) by the same factor. A strain rate dependent bond breakage criterion has been developed and model results were found to compare well with the experimental data.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abbas, A., Masad, E., Papagiannakis, T., and Harman, T. (2007). “Micromechanical modelling of the viscoelastic behaviour of asphalt mixtures using the discrete-element method.” Int. J. Geomech., 7(2), 131–139.
Adhikari, S., and You, Z. (2008). “3D microstructural models for asphalt mixtures using X-ray computed tomography images.” International Journal of Pavement Research and Technology, 3(1), 94–99.
Blaauwendraad, J., and Scarpas, A. (2000) “3D finite-element simulation of damage in asphalt concrete pavement.” MCCI 2000—Int. Symp. on Modern Concrete Composites & Infrastructures, Vol. I.
Buttlar, W. G., and You, Z. (2001). “Discrete element modelling of asphalt concrete: A microfabric approach.” Journal of Transportation Board, 1757, 111–118.
Cheung, C. Y., and Cebon, D. (1997). “Thin film deformation behaviour of power-law creeping materials.” J. Eng. Mech., 123(11), 1138–1152.
Collop, A. C., Lee, Y., and McDowell, G. R. (2004). “Use of the distinct element method to model the deformation behaviour of an idealized asphalt mixture.” Int. J. Pavement Eng., 5(1), 1–7.
Collop A. C., McDowell G. R., and Lee Y. (2006) “Modelling dilation in idealised asphalt mixture using discrete element modeling.” Granular Matter, 8(3–4), 175–184.
Collop, A. C., McDowell, G. R., and Lee, Y. (2007). “On the use of discrete element modelling to simulate the viscoelastic deformation behaviour of an idealised asphalt mixture.” Geomech. Geoeng., 2, 77–86.
Collop, A. C., Scarpas, A., Kasbergen, C., and de Bondt, A. (2003). “Development and finite-element implementation of a stress dependent elastic-visco-plastic constitutive model with damage for asphalt.” Transportation Research Record 1832, Transportation Research Board, Washington D.C., 96–104.
Cundall, P. A., and Strack, O. D. L. (1979). “A discrete numerical model for granular assemblies.” Geotechnique, 29(1), 47.
Deshpande, V. S. (1997). “Steady-state deformation behaviour of bituminous mixes.” Ph.D. thesis, Dept. of Engineering, Univ. of Cambridge, Cambridge, U.K.
Erkens, S. M. J. G., Liu, X., Scarpas, A., Molenaar, A. A. A., and Blaauwendraad, J. (2002). “Asphalt concrete response: Experimental determination and finite element implementation.” Proc., 9th Int. Conf. on Asphalt Pavements, ISAP, Minn.
Grenfell, J. R., Taherkhani, H., Collop, A. C., Airey, G. D., and Scarpas, A. (2008). “Deformation characterisation of asphalt concrete behaviour.” Proc., AAPT 2008, AAPT, Minn.
Harvey, J. A. F. (2000). “Bitumen films in tension.” Ph.D. thesis, Univ. of Cambridge, Cambridge, U.K.
Itasca Consulting Group Inc. (2003). Particle flow code in 3 dimensions—PFC3D series, Minn.
Kim, H., Wagoner, M. P., and Buttlar, W. G. (2007). “Fracture modelling considered rate-dependency of asphalt concrete using discrete element method.” Proc., Int. Conf. on Advanced Characterisation of Pavement and Soil Engineering Materials.
Kim, H., Wagoner, M. P., and Buttlar, W. G. (2008). “Simulation of fracture behaviour in asphalt concrete using a heterogeneous cohesive zone discrete element model.” J. Mater. Civ. Eng., 20(8), 552–563.
Lee, Y. W. (2006). “Discrete element modelling of idealised asphalt mixture.” Ph.D. thesis, Univ. of Nottingham, Nottingham, U.K.
Liu, Y., Dai, Q., and You, Z. (2009). “Viscoelastic model for discrete element simulation of asphalt mixtures.” J. Eng. Mech., 135(4), 324–333.
Liu, Y., and You, Z. (2008). “Simulation of cyclic loading tests for asphalt mixtures using user defined models within discrete element method.” Proc., GeoCongress 2008: Characterization, Monitoring, and Modeling of GeoSystems, Geotechnical Special Publication (GSP 179), 742–749.
Lu, M., and McDowell, G. R. (2008). “Discrete element modelling of railway ballast under triaxial conditions.” Geomech. Geoeng., 3(4), 257–270.
Mahmoud, E. (2008). “Discrete element modelling of influence of aggregate graduation and aggregate properties of fracture in asphalt mixes.” Ph.D. thesis, Zachry Dept. of Civil Engineering, Texas A&M Univ., College Station, Tex.
McDowell, G. R., and Harireche, O. (2002). “Discrete element modelling of soil particle fracture.” Geotechnique, 52(2), 131–135.
Robertson, D. (2000). “Numerical simulations of crushable aggregates.” Ph.D. thesis, Univ. of Cambridge, Cambridge, U.K.
Rothenburg, L., and Bathurst, R. J. (1992). “Micromechanical features of granular assemblies with planar elliptical particles.” Geotechnique, 42(1), 79–95.
Ullidtz, P. (2003). “Analytical tools for design of flexible pavements.” Proc. 9th Int. Conf. on Asphalt Pavements, Vol. 3, ISAP, Minn., 22–37.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 23 • Issue 1 • January 2011
Pages: 2 - 11
Copyright
© 2011 ASCE.
History
Received: Mar 27, 2009
Accepted: Mar 4, 2010
Published online: Mar 16, 2010
Published in print: Jan 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.