Revisiting the Energy-Momentum Method for Rating Vertical Sluice Gates under Submerged Flow Conditions
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Irrigation and Drainage Engineering
Volume 139, Issue 4
Abstract
Submerged sluice gates may be used as discharge measuring structures in irrigation channels. One commonly used model to predict discharge under submerged gates is based on the simultaneous solution of the energy and momentum equations (EM method). The conventional assumption for the solution is that the roller forming downstream of the gate is a static bubble of water with zero net flux of both momentum and kinetic energy. Energy losses along the submerged gate flow are commonly neglected. In this study, rational analysis of the EM method shows that the roller momentum flux and the energy loss may be considerable. A novel formulation of the EM method accounting for these two phenomena is proposed. Although it yields results similar to those of the conventional method, the new method introduces rationality in the application of the EM equations for submerged gate flow and helped to critically revise the assumptions in which the conventional EM method is based.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to express their gratitude to IIHR-Hydroscience and Engineering Archives, Iowa City, in particular to archivist Dr. Connie Mutel for providing reprints of the theses of Liu (1949) and Henry (1950). The excellent suggestions and comments received from Prof. W.H. Hager, ETH Zurich, are acknowledged. The critical comments of the reviewers of this work helped to make a more precise presentation of the critical assessment presented in this work, for which the authors are grateful.
References
Belaud, G., Cassan, L., and Baume, J. P. (2009). “Calculation of contraction coefficient under sluice gates and application to discharge measurement.” J. Hydraul. Eng., 135(12), 1086–1091.
Bos, M. G. (1976). Discharge measurement structures, Publication 20, International Institute for Land Reclamation (ILRI), Wageningen, the Netherlands.
Castro-Orgaz, O., Lozano, D., and Mateos, L. (2010). “Energy and momentum velocity coefficients for calibration of submerged sluice gates in irrigation canals.” J. Irrig. Drain. Eng., 136(9), 610–616.
Chanson, H. (2004). The hydraulics of open channel flows: An introduction, Butterworth-Heinemann, Oxford, UK.
Chow, V. T. (1959). Open channel hydraulics, McGraw-Hill, New York.
Clemmens, A. J., Strelkoff, T. S., and Replogle, J. A. (2003). “Calibration of submerged radial gates.” J. Hydraul. Eng., 129(9), 680–687.
Defina, A., and Susin, F. M. (2003). “Hysteretic behavior of the flow under a vertical sluice gate.” Phys. Fluids, 15(9), 2541–2548.
Dey, S., Nath, T. K., and Bose, S. K. (2010). “Submerged wall-jets subjected to injection and suction from the wall.” J. Fluid Mech., 653, 57–97.
Dey, S., and Sarkar, A. (2008). “Characteristics of turbulent flow in submerged jumps on rough beds.” J. Eng. Mech., 134(1), 49–59.
Escande, L. (1938). “Etude théorique et expérimentale de l’écoulement par vanne de fond (Theoretical and experimental study of flow below gate).” Rev. Générale de l’Hydraulique, 4(19), 25–29 (in French).
Escande, L. (1939). “Etude théorique et expérimentale de l’écoulement par vanne de fond (Theoretical and experimental study of flow below gate).” Rev. Générale de l’Hydraulique, 5(25), 21–34 (in French).
Henderson, F. M. (1966). Open channel flow, MacMillan, New York.
Henry, H. R. (1950). “A study of flow from a submerged sluice gate.” M.S. thesis, Dept. of Mechanics and Hydraulics, Iowa State Univ., Ames, IA.
Jain, S. C. (2001). Open channel flow, Wiley, New York.
Liu, H. K. (1949). Diffusion of flow from a submerged sluice gate. M.S. thesis, Dept. of Mechanics and Hydraulics, Iowa State Univ., Ames, IA.
Lozano, D., Mateos, L., Merkley, G. P., and Clemmens, A. J. (2009). “Field calibration of submerged sluice gates in irrigation canals.” J. Irrig. Drain. Eng., 135(6), 763–773.
Madsen, P. A., and Svendsen, I. A. (1983). “Turbulent bores and hydraulic jumps.” J. Fluid Mech., 129, 1–25.
Montes, J. S. (1998). Hydraulics of open channel flow, ASCE Press, Reston, VA.
Naudascher, E. (1991). Hydrodynamic forces, IAHR hydraulic structures design manual 3, International Association of Hydraulic Research, Delft, the Netherlands.
Oosterholt, G. A. (1949). “An investigation of the energy dissipated in a surface roller.” Appl. Sci. Res., A1, 107–130.
Ohtsu, I., Yasuda, Y., and Awazu, S. (1990). “Free and submerged hydraulic jumps in rectangular channels.”, Institute of Science and Technology, Nihon Univ., Japan.
Rajaratnam, N. (1965). “Submerged hydraulic jump.” J. Hydraul. Div., 91(HY4), 71–96.
Rajaratnam, N., and Subramanya, K. (1967a). “Flow equation for the sluice gate.” J. Irrig. Drain. Div., 93(IR3), 167–186.
Rajaratnam, N., and Subramanya, K. (1967b). “Flow inmediately below submerged sluice gate.” J. Hydraul. Div., 93(HY4), 57–77.
Rouse, H. (1938). Fluid mechanics for hydraulic engineers, Engineering societies monographs, Wiley, New York.
Rouse, H. (1950). Engineering hydraulics, Wiley, New York.
Rouse, H. (1961). “Energy transformation in zones of separation.” Proc., 9th Int. Association of Hydraulic Research Congress, Dubrovnik, 1291–1302.
Schröder, R. (1957). “Ein Beitrag zur Frage der Energieumwandlung und Turbulenz diskontinuierlicher Wasserströmungen mit freier Oberfläche (A contribution to the question of energy dissipation and the turbulence of discontinuous water flow).” Ph.D. dissertation, Institute of Hydraulic Engineering and Water Resources Management, Technische Universität Berlin, Berlin (in German).
Sepúlveda, C., Gómez, M., and Rodellar, J. (2009). “Benchmark of discharge calibration methods for submerged sluice gates.” J. Irrig. Drain. Eng., 135(5), 676–682.
Svendsen, I. A., Veeramony, J., Bakunin, J., and Kirby, J. T. (2000). “The flow in weak turbulent hydraulic jumps.” J. Fluid Mech., 418, 25–57.
Toch, A. (1955). “Discharge characteristics of tainter gates.” Trans. ASCE, 120, 290–300.
Wahl, T. L. (2005). “Refined energy correction for calibration of submerged radial gates.” J. Hydraul. Eng., 131(6), 457–466.
Woycicki, K. (1931). “Wassersprung, Deckwalze und Ausfluss unter einer Schütze [Hydraulic jump, roller and outflow from below a gate].” Ph.D. dissertation 639, ETH Zurich, Zurich, Switzerland (in German).
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Feb 29, 2012
Accepted: Oct 9, 2012
Published online: Oct 11, 2012
Published in print: Apr 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.