Experimental Study of Impact Pressures on Deep Plunge Pool Floors Generated by Submerged Inclined Jets with Controlled Aeration
Publication: Journal of Hydraulic Engineering
Volume 146, Issue 4
Abstract
Hydrodynamic pressures on a plunge pool floor due to submerged aerated jets are of interest in many engineering fields. For the present study, dynamic pressures on a deep plunge pool floor due to submerged inclined jets with forced aeration were systematically investigated. The incoming flow thickness and air concentration were controlled by a plane pressurized nozzle in a hydraulic model. The results confirmed the asymmetrical distributions of the pressures on the plunge pool floor. Both the maximum mean pressure and pressure fluctuation locations remained practically unaffected under different incoming jet conditions. The mean pressure coefficient decreased with jet aeration and increased with the relative jet thickness. The coupling effect of jet aeration and thickness on the pressure fluctuation coefficient occurred in two ways. At a small relative jet thickness, a critical threshold existed for flow air concentration in which the fluctuation pressure coefficient increased and subsequently decreased with increasing air concentration. At a large relative jet thickness, the fluctuation pressure coefficient increased throughout with increasing air concentration. In general, a combination of decreased jet thickness and enhanced jet aeration can reduce impact on the bottom floor of a deep plunge pool. These research results provide reference for air–water flow discharge design in engineering applications.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the suggestions and comments provided by the editors and reviewers. The authors thank the financial support from the National Natural Science Foundation of China (Grant number 51609162) and the National Key Research and Development Program of China (Grant number 2016YFC0401901).
References
Albertson, M. L., Y. Dai, R. Jensen, and H. Rouse. 1950. “Diffusion of submerged jets.” Trans. Am. Soc. Civ. Eng. 115 (1): 639–664.
Ballio, F., S. Franzetti, and M. G. Tanda. 1994. “Pressure fluctuations induced by turbulent circular jets impinging on a flat plate.” Excerpta 7: 41–59.
Beltaos, S. 1976. “Oblique impingement of plane turbulent jets.” J. Hydraul. Div. 102 (9): 1177–1192.
Biń, A. K. 1993. “Gas entrainment by plunging liquid jets.” Chem. Eng. Sci. 48 (21): 3585–3630. https://doi.org/10.1016/0009-2509(93)81019-R.
Bollaert, E. F. R. 2002. “Transient water pressures in joints and formation of rock scour due to high-velocity jet impact.” In Communication 13, Laboratoire de Constructions Hydrauliques. Lausanne, Switzerland: Ecole Polytechnique Fédérale de Lausanne.
Bollaert, E., and A. Schleiss. 2003a. “Scour of rock due to the impact of plunging high velocity jets. Part I: A state-of-the-art review.” J. Hydraul. Res. 41 (5): 451–464. https://doi.org/10.1080/00221680309499991.
Bollaert, E., and A. Schleiss. 2003b. “Scour of rock due to the impact of plunging high velocity jets. Part II: Experimental results of dynamic pressures at pool bottoms and in one- and two-dimensional closed end rock joints.” J. Hydraul. Res. 41 (5): 465–480. https://doi.org/10.1080/00221680309499992.
Bollaert, E., and A. Schleiss. 2005. “Physically based model for evaluation of rock scour due to high-velocity jet impact.” J. Hydraul. Eng. 131 (3): 153–165. https://doi.org/10.1061/(ASCE)0733-9429(2005)131:3(153).
Bombardelli, F. A., M. Palermo, and S. Pagliara. 2018. “Temporal evolution of jet induced scour depth in cohesionless granular beds and the phenomenological theory of turbulence.” Phys. Fluids 30 (8): 085109. https://doi.org/10.1063/1.5041800.
Brattberg, T., and H. Chanson. 1998. “Air entrapment and air bubble dispersion at two-dimensional plunging water jets.” Chem. Eng. Sci. 53 (24): 4113–4127. https://doi.org/10.1016/S0009-2509(98)80004-3.
Canepa, S., and W. H. Hager. 2003. “Effect of jet air content on plunge pool scour.” J. Hydraul. Eng. 129 (5): 358–365. https://doi.org/10.1061/(ASCE)0733-9429(2003)129:5(358).
Castillo, L. G. 2002. “Int. workshop on rock scour due to high-velocity jets.” In Parametrical analysis of the ultimate scour and mean dynamic pressures at plunge pools. Lausanne, Switzerland: École Polytechnique Fédérale de Lausanne.
Castillo, L. G. 2006. “Aerated jets and pressure fluctuation in plunge pools.” In Proc., 7th Int. Conf. on Hydroscience & Engineering, 1–23. Philadelphia: Drexel Univ.
Castillo, L. G., M. C. José, and A. Blázquez. 2015. “Plunge pool dynamic pressures: A temporal analysis in the nappe flow case” J. Hydraul. Res. 53 (1): 101–118. https://doi.org/10.1080/00221686.2014.968226.
Chanson, H. 2009. “Turbulent air–water flows in hydraulic structures: Dynamic similarity and scale effects.” Environ. Fluid Mech. 9 (2): 125–142. https://doi.org/10.1007/s10652-008-9078-3.
Chanson, H. 2013. “Hydraulics of aerated flows: Qui pro quo?” J. Hydraul. Res. 51 (3): 223–243. https://doi.org/10.1080/00221686.2013.795917.
Chanson, H., S. Aoki, and A. Hoque. 2004. “Physical modelling and similitude of air bubble entrainment at vertical circular plunging jets.” Chem. Eng. Sci. 59 (4): 747–758. https://doi.org/10.1016/j.ces.2003.11.016.
Chen, J. G., J. M. Zhang, W. L. Xu, and Y. Peng. 2014. “Characteristics of the velocity distribution in a hydraulic jump stilling basin with five parallel offset jets in a twin-layer configuration.” J. Hydraul. Eng. 140 (2): 208–217. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000817.
Cola, R. 1965. “Energy dissipation of a high-velocity vertical jet entering a basin.” In Proc., 11th IAHR Congress, Leningrad, Russia: International Association for Hydro-Environment Engineering and Research.
Crowe, C. T. 2000. “On models for turbulence modulation in fluid—Particle flows.” Int. J. Multiphase Flow 26 (5): 719–727. https://doi.org/10.1016/S0301-9322(99)00050-6.
Cummings, P. D., and H. Chanson. 1997a. “Air entrainment in the developing flow region of plunging jets. I: Theoretical development.” J. Fluids Eng. 119 (3): 597–602. https://doi.org/10.1115/1.2819286.
Cummings, P. D., and H. Chanson. 1997b. “Air entrainment in the developing flow region of plunging jets. II: Experimental.” J. Fluids Eng. 119 (3): 603–608. https://doi.org/10.1115/1.2819287.
Deng, J., W. Xu, J. Zhang, J. Qu, and Q. Yang. 2008. “A new type of plunge pool—Multi-horizontal submerged jets.” Sci. China Technol. Sci. 51 (12): 2128–2141. https://doi.org/10.1007/s11431-008-0237-z.
Deng, J., Z. Yang, Z. Tian, F. Zhang, W. Wei, X. You, and W. Xu. 2016. “A new type of leak-floor flip bucket.” Sci. China Technol. Sci. 59 (4): 565–572. https://doi.org/10.1007/s11431-015-5925-x.
Dong, Z. Y. 1993. A study on effects of aeration on hydraulic characteristics in receiving pool by plunging jet. [In Chinese.] Ph.D. thesis, Dept. of Hydraulic Engineering, Sichuan Univ.
Duarte, R. 2014. Influence of air entrainment on rock scour development and block stability in plunge pools. Ph.D. thesis, Laboratory of Constructions Hydraulics, Univ. of Lisbon.
Ervine, D. A., and H. T. Falvey. 1987. “Behaviour of turbulent water jets in the atmosphere and in plunge pools.” Proc. Inst. Civ. Eng. 83 (1): 295–314. https://doi.org/10.1680/iicep.1987.353.
Ervine, D. A., H. T. Falvey, and W. Withers. 1997. “Pressure fluctuations on plunge pool floors.” J. Hydraul. Res. 35 (2): 257–279. https://doi.org/10.1080/00221689709498430.
Fiorotto, V., S. Barjastehmaleki, and E. Caroni. 2016. “Stability analysis of plunge pool linings.” J. Hydraul. Eng. 142 (11): 04016044. https://doi.org/10.1061/(ASCE)HY.1943-7900.0001175.
Fiorotto, V., and A. Rinaldo. 1992a. “Fluctuating uplift and lining design in spillway stilling basins.” J. Hydraul. Eng. 118 (4): 578–596. https://doi.org/10.1061/(ASCE)0733-9429(1992)118:4(578).
Fiorotto, V., and A. Rinaldo. 1992b. “Turbulent pressure fluctuations under hydraulic jumps.” J. Hydraul. Res. 30 (4): 499–520. https://doi.org/10.1080/00221689209498897.
Franzetti, S., and M. G. Tanda. 1987. “Analysis of turbulent pressure fluctuation caused by a circular impinging jet.” In Proc., Int. Symp. New Technology in Model Testing in Hydraulic Research, 85–91. New Delhi, India: The Board.
Hager, W. H., and R. M. Boes. 2014. “Hydraulic structures: A positive outlook into the further.” J. Hydraul. Res. 52 (3): 299–310. https://doi.org/10.1080/00221686.2014.923050.
Hartung, F., and E. Häusler. 1973. “Scours, stilling basins and downstream protection under free overall jets at dams.” In Proc., 11th Congress on Large Dams, 39–56. Madrid, Spain: International Association for Hydro-Environment Engineering and Research.
Heller, V. 2011. “Scale effects in physical hydraulic engineering models.” J. Hydraul. Res. 49 (3): 293–306. https://doi.org/10.1080/00221686.2011.578914.
Juon, R., and W. H. Hager. 2000. “Flip bucket without and with deflectors.” J. Hydraul. Eng. 126 (11): 837–845. https://doi.org/10.1061/(ASCE)0733-9429(2000)126:11(837).
Lin, B. N., and J. J. Lian. 1988. “A calculation of pressure fluctuation on the bottom floor impacted by 2-D plunging jet flows.” [In Chinese.] Shuili Xuebao 12 (6): 34–40.
Liu, P. Q., J. R. Dong, and C. Yu. 1998. “Experimental investigation of fluctuation uplift on rock blocks at the bottom of the scour pool downstream of three-Gorges Spillways.” J. Hydraul. Res. 36 (1): 55–68. https://doi.org/10.1080/00221689809498377.
Manso, P. A. 2006. “The influence of pool geometry and induced flow patterns on rock scour by high-velocity plunging jets.” In Communication 25, laboratoire de constructions hydrauliques. Lausanne, Switzerland: Ecole Polytechnique Fédérale de Lausanne.
Manso, P. A., E. F. R. Bollaert, and A. J. Schleiss. 2007. “Impact pressures of turbulent high-velocity jets plunging in pools with flat bottom.” Exp. Fluids 42 (1): 49–60. https://doi.org/10.1007/s00348-006-0219-5.
Manso, P. A., E. F. R. Bollaert, and A. J. Schleiss. 2009. “Influence of plunge pool geometry on high-velocity jet impact pressures and pressure propagation inside fissured rock media.” J. Hydraul. Eng. 135 (10): 783–792. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000090.
Manso, P. A., V. Fiorotto, E. Bollaert, and A. J. Schleiss. 2004. “Discussion of ‘effect of jet content on plunge pool scour’ by Stefano Canepa and Willi H. Hager.” J. Hydraul. Eng. 130 (11): 1128–1130. https://doi.org/10.1061/(ASCE)0733-9429(2004)130:11(1128).
May, R. W. P., and I. R. Willoughby. 1991. Impact pressures in plunge pool basins due to vertical falling jets. Wallingford, UK: HR Wallingford.
McKeogh, E. 1978. “A study of air entrainment using plunging water jets.” Ph.D. thesis, Dept. of Civil Engineering, Queens Univ.
McKeogh, E. J., and E. M. Elsawy. 1980. “Air retained in pool by plunge water jet.” J. Hydraul. Div. 106 (10): 1577–1593.
Melo, J. F. 2002. “Reduction of plunge pool floor dynamic pressure due to jet air entrainment.” In Proc., Int. Workshop on Rock Scour due to High-Velocity Jets. Lisse, Netherlands: Swets & Zeitlinger.
Melo, J. F., A. N. Pinheiro, and C. M. Ramos. 2006. “Forces on plunge pool slabs: Influence of joints location and width.” J. Hydraul. Eng. 132 (1): 49–60. https://doi.org/10.1061/(ASCE)0733-9429(2006)132:1(49).
Pagliara, S., W. H. Hager, and J. Unger. 2008. “Temporal evolution of plunge pool scour.” J. Hydraul. Eng. 134 (11): 1630–1638. https://doi.org/10.1061/(ASCE)0733-9429(2008)134:11(1630).
Pfister, M., W. H. Hager, and R. M. Boes. 2014. “Trajectories and air flow features of ski jump-generated jets.” J. Hydraul. Res. 52 (3): 336–346. https://doi.org/10.1080/00221686.2013.875072.
Pinheiro, A. N., and J. F. Melo. 2008. “Effect of jet aeration on hydrodynamic forces on plunge pool floors.” Can. J. Civ. Eng. 35 (5): 521–530. https://doi.org/10.1139/l07-138.
Pope, S. B. 2002. Turbulent flows. Cambridge, UK: Cambridge University Press.
Puertas, J. A. 1994. “Criterios hidràulicos para el diseño de cuencos de disipación de energia en presas bóveda con vertido libre por coronación.” [In Spanish.] Ph.D. thesis, Departamento de Ingeniería Hidráulica, Universitát Politècnica de Catalunya.
Ramos, C. M. 1979. “Statistical characteristics of the pressure field of crossed flows in energy dissipation structures.” In Proc., 11th ICOLD Congress, 39–56. Madrid, Spain: International Commission on Large Dams.
Reinius, E. 1986. “Rock erosion.” Int. Water Power Dam Constr. 38 (6): 43–48.
Schleiss, A. 2002. “Scour evaluation in space and time—The challenge of dam designers.” In Rock Scour due to falling high-velocity jets, edited by A. J. Schleiss and E. Bollaert, 2–33. Lisse, Netherlands: Swets & Zeitlinger.
Schwalt, M., and W. H. Hager. 1992. “Die strahlbox (The jet box).” [In German.] Schweiz. Ing. Archit. 110 (27): 547–549.
Schwarz, M. P. 2015. “Bubble induced turbulence in two-fluid simulation of bubbly flow.” In Proc., 26th Int. Symp. Transport Phenomena, 46–53. Leoben, Austria: Montanuniversitat Leoben.
Si, J.-H., S.-Y. Lim, and X.-K. Wang. 2018. “Flow structures in evolving scour holes caused by a plunging jet downstream of a weir.” J. Hydraul. Eng. 144 (6): 04018018. https://doi.org/10.1061/(ASCE)HY.1943-7900.0001452.
Steiner, R., V. Heller, W. H. Hager, and H.-E. Minor. 2008. “Deflector ski jump hydraulics.” J. Hydraul. Eng. 134 (5): 562–571. https://doi.org/10.1061/(ASCE)0733-9429(2008)134:5(562).
Toso, J. W., and C. E. Bowers. 1988. “Extreme pressures in hydraulic jump stilling basins.” J. Hydraul. Eng. 114 (8): 829–843. https://doi.org/10.1061/(ASCE)0733-9429(1988)114:8(829).
Valero, D., and D. B. Bung. 2018. “Reformulating self-aeration in hydraulic structures: Turbulent growth of free surface perturbations leading to air entrainment.” Int. J. Multiphase Flow 100 (3): 127–142. https://doi.org/10.1016/j.ijmultiphaseflow.2017.12.011.
Wang, S. K., S. J. Lee, O. C. Jones, and R. T. Lahey. 1990. “Statistical analysis of turbulent two-phase pipe flow.” J. Fluids Eng. 112 (1): 89–95. https://doi.org/10.1115/1.2909374.
Wei, W. R., J. Deng, and B. Liu. 2013. “Influence of aeration and initial water thickness on axial velocity attenuation of jet flows.” J. Zhejiang Univ. Sci. A 14 (5): 362–370. https://doi.org/10.1631/jzus.A1200312.
Withers, W. 1991. Pressure fluctuations in the plunge pool of an impinging jet spillway. Ph.D. thesis, Dept. of Civil Engineering, Univ. of Glasgow.
Xu, D. M., and Yu, C. 1983. “Characteristis of impact pressure and pressure fluctuations on the floor caused by plane jet flow.” [In Chinese.] Shuili Xuebao 5 (6): 52–58.
Xu, W., J. Deng, J. Qu, S. Liu, and W. Wang. 2004. “Experimental investigation on influence of aeration on plane jet scour.” J. Hydraul. Eng. 130 (2): 160–164. https://doi.org/10.1061/(ASCE)0733-9429(2004)130:2(160).
Zhang, G., D. Valero, D. B. Bung, and H. Chanson. 2018. “On the estimation of free-surface turbulence using ultrasonic sensors” Flow Meas. Instrum. 60 (Apr): 171–184. https://doi.org/10.1016/j.flowmeasinst.2018.02.009.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Aug 29, 2018
Accepted: Aug 13, 2019
Published online: Feb 12, 2020
Published in print: Apr 1, 2020
Discussion open until: Jul 12, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.