Computational Fluid Dynamics Modeling for the Design of Large Primary Settling Tanks
Publication: Journal of Hydraulic Engineering
Volume 137, Issue 3
Abstract
Settling tanks are used to remove solids at wastewater treatment plants. Many numerical models have been proposed to simulate the settling process and to improve tank efficiency. In this research, a three-dimensional (3D) numerical model is developed to simulate large primary settling tanks. In the proposed model, the non-Newtonian properties of the sludge flow in the settling tank are described by a Bingham plastic rheological model. To eliminate the singularity inherited in the rheological model, a modified constitutive relation is used in both the yielded and unyielded regions. Hindered settling of particles in the settling tank is also modeled. Tracer study, where a massless scalar is injected and transported, is done to investigate the tank’s residence time. This numerical model is used to improve the design of the primary settling tanks, which will be built in Chicago. The Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) is in the process of building new preliminary treatment facilities at their Calumet Water Reclamation Plant (CWRP), including twelve 155-ft-diameter primary settling tanks (PSTs) designed to treat flows up to ( (MGD). The computational fluid dynamics (CFD) model simulated solids removal efficiencies based on a particle size distribution similar to the one observed in the CWRP influent. The results were used to establish the design basis for tank side-water depth, inlet feedwell dimensions, etc., resulting in improved performance and substantial reduction in construction costs.
Get full access to this article
View all available purchase options and get full access to this article.
References
Brennan, D. (2001). “The numerical simulation of two-phase flows in settling tanks.” Ph.D. thesis, Univ. of London, London.
Cho, S., Colin, F., Sardin, M., and Prost, C. (1993). “Settling velocity model of activated sludge.” Water Res., 27(7), 1237–1242.
Clercq, B. (2003). “Computational fluid dynamics of settling tanks: Development of experiments and rheological, settling and scraper submodels.” Ph.D. thesis, Univ. of London, London.
Dahl, C. (1993). “Modeling of flow field and settling in secondary settling tanks.” Ph.D. thesis, Univ. of Aalborg, Aalborg, Denmark.
Dahl, C., Larsen, T., and Petersen, O. (1994). “Numerical modeling and measurement in a test secondary settling tank.” Water Sci. Technol. Water Supply, 30(2), 219–228.
DeVantier, B., and Larock, B. (1983). “Sediment transport in stratified turbulent flow.” J. Hydraul. Eng., 109(12), 1622–1635.
DeVantier, B., and Larock, B. (1986). “Modeling a recirculating density-driven turbulent flow.” Int. J. Numer. Methods Fluids, 6, 241–253.
DeVantier, B., and Larock, B. (1987). “Modeling sediment-induced density currents in sedimentation basins.” J. Hydraul. Eng., 113(1), 80–94.
Dick, R., and Ewing, B. (1967). “The rheology of activated sludge.” J. Water Pollut. Control Fed., 39(4), 543–560.
Dupont, R., and Dahl, C. (1995). “A one-dimensional model for a secondary settling tank including density current and short-circuiting.” Water Sci. Technol., 31(2), 215–224.
Gerges, H., and McCorquodale, J. (1997). “Modeling of flow in rectangular sedimentation tanks by an explicit third-order upwinding technique.” Int. J. Numer. Methods Fluids, 24(6), 537–561.
Huang, X., and and Garcia, M. H. (1997). “A perturbation solution for Bingham plastic mud flows.” J. Hydraul. Eng., 123(11), 986–994.
Huang, X., and and Garcia, M. H. (1998). “A Herschel-Bulkley model for mud flows down a slope.” J. Fluid Mech.374, 305–333.
Imam, E. (1981). “Numerical modeling of rectangular clarifiers.” Ph.D. thesis, Univ. of Windsor, Ontario, Canada.
Ishii, M. (1977). “One-dimensional drift-flux model and constitutive equations for relative motion between phases in various two-phase flow regimes.” Rep. ANL 77-47, Argonne National Lab, Chicago.
Issa, R. (1986). “Solution of the implicitly discretised fluid flow equations by operator-splitting.” J. Comput. Phys., 62(1), 40–65.
Jin, Y., Guo, Q., and Viraraghavan, T. (2000). “Modeling of class I settling tanks.” J. Environ. Eng., 126(8), 754–760.
Karl, J., and Wells, S. (1999). “Numerical model of sedimentation/thickening with inertial effects.” J. Environ. Eng., 125(9), 792–806.
Krebs, P. (1995). “Success and shortcomings of clarifier modeling.” Water Sci. Technol., 31(2), 181–191.
Krebs, P., Vischer, D., and Gujer, W. (1995). “Inlet structure design for final clarifiers.” J. Environ. Eng., 121(8), 558–564.
Krishnappan, B., and Marsalek, J. (2002). “Modeling of flocculation and transport of cohesive sediment from an on-stream stormwater detention pond.” Water Res., 36, 3849–3859.
Lakehal, D., Krebs, P., Krijgsman, J., and Rodi, W. (1999). “Computing shear flow and sludge blanket in secondary clarifiers.” J. Hydraul. Eng., 125(3), 253–262.
Li, D., and Ganczarczyk, J. (1987). “Stroboscopic determination of settling velocity, size and porosity of activated sludge flocs.” Water Res., 21(3), 257–262.
Liu, X., and García, M. H. (2007a). “Numerical modeling of the Calumet water reclamation plant (CWRP) primary settling tanks, Hydraulic Engineering Series.” Rep. No. 80, Dept. of Civil and Environmental Engineering, Univ. of Illinois at Urbana-Champaign.
Liu, X., and García, M. H. (2007b). “Numerical simulation of rectangular settling tank with scraper using dynamic mesh.” Proc., 5th International Symposium on Environmental Hydraulics, D. Boyer and O. Alexandrova, eds., Arizona State Univ., Tempe, AZ.
Lyn, D., and Rodi, W. (1990). “Turbulence measurements in model settling tank.” J. Hydraul. Eng., 116(1), 3–21.
Lyn, D., Stamou, A., and Rodi, W. (1992). “Density currents and shear-induced flocculation in sedimentation tanks.” J. Hydraul. Eng., 118(6), 849–867.
Lyn, D., and Zhang, Z. (1989). “Boundary-fitted numerical modeling of sedimentation tanks.” Proc. 23rd Cong. IAHR, National Research Council of Canada, Ottawa. 331–338.
Marle, C., and Kranenburg, C. (1994). “Effects of gravity currents in circular secondary clarifiers.” J. Environ. Eng., 120(4), 943–960.
Mazzolani, G., Pirozzi, F., and d’Antoni, G. (1998). “A generalized settling approach in the numerical modeling of sedimentation tanks.” Water Sci. Technol., 38(3), 95–102.
OpenCFD. (2007). OpenFOAM—The Open Source CFD Toolbox—User’s Guide, 1.4.1 Ed., OpenCFD Ltd., UK.
Papanastasiou, T. (1987). “Flows of materials with yield.” J. Rheol., 31(5), 385–404.
Pedocchi, F., and García, M. H. (2006). “Evaluation of the LISST-ST instrument for suspended particle size distribution and settling velocity measurements.” Continental Shelf Res., 26(8), 943–958.
Richardson, J., and Zaki, W. (1954). “Sedimentation and fluidization. Part 1.” Trans. Inst. Chem. Eng., 32, 35–53.
Rodi, W. (1984). Turbulence Models and Their Application in Hydraulics, A State-Of-Art Review, 2nd Ed., IAHR, Delft, The Netherlands.
Schamber, D., and Larock, B. (1983). “Particle concentration predictions in settling basins.” J. Environ. Eng., 109(3), 753–763.
Stamou, A. (1991). “On the prediction of flow and mixing in settling tanks using a curvature-modified model.” Appl. Math. Model., 15, (7), 351–358.
Stamou, A., Adams, E., and Rodi, W. (1989). “Numerical modeling of flow and settling in primary rectangular clarifiers.” J. Hydraul. Res., 27(5), 665–682.
Takacs, I., Patry, G., and Nolasco, D. (1991). “A dynamic model of the clarification-thickening process.” Water Res., 25(10), 1263–1271.
Vesilind, A. (1968). “Discussion of evaluation of activated sludge thickening theories.” J. Sanit. Eng. Div., 94, 182–191.
Vitasovic, Z., Zhou, S., McCorquodale, J., and Lingren, K. (1997). “Secondary clarifier analysis using data from the clarifier research technical committee protocol.” Water Environ. Res., 69(5), 999–1007.
Watts, R., Svoronos, S., and Koopman, B. (1996). “One dimensional clarifier model with sludge blanket heights.” J. Environ. Eng., 122(12), 1094–1100.
Weller, H., Tabor, G., Jasak, H., and Fureby, C. (1998). “A tensorial approach to computational continuum mechanics using object-oriented techniques.” Comput. Phys., 12(6), 620–631.
Zhou, S., and McCorquodale, J. (1992). “Modeling of rectangular settling tanks.” J. Hydraul. Eng., 118(10), 1391–1405.
Information & Authors
Information
Published In
Journal of Hydraulic Engineering
Volume 137 • Issue 3 • March 2011
Pages: 343 - 355
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Apr 13, 2009
Accepted: Aug 22, 2010
Published online: Aug 31, 2010
Published in print: Mar 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.