Influences of Suction on Plate Load Tests on Unsaturated Silty Sands
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 144, Issue 8
Abstract
In this study, results of plate load tests performed on saturated and unsaturated silty sand samples are presented. Very little is known about how to interpret the plate load test when performed on unsaturated soils comprising silt–sand mixtures because the few published studies have been limited to either unsaturated clean sands or clays. The new plate load test results are interpreted using a bearing capacity equation, applicable when nonuniform profiles prevail in the soil, where is the contribution of suction to the effective stress. The interrelation between , strength, and bearing capacity is shown. There is good agreement between measured and computed bearing capacities. Assuming remains constant during a plate load test, compared to assumptions of constant suction or constant moisture content, simplifies interpretation without significant loss of accuracy. For a particular soil density, the bearing capacity for an unsaturated condition is found to be much larger than that for a fully saturated condition. It is also shown that the effect of suction on the bearing capacity is dependent on the initial location of the hydraulic state on the soil–water characteristic curve. Failing to account for suction and the hydraulic loading history may lead to incorrect interpretations. It is also demonstrated how plate load tests may be used to infer the value of at the soil surface.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Thanks goes to the Australian Research Council for funding through Grant DP140103142.
References
Adams, M. T., and J. G. Collin. 1997. “Large model spread footing load tests on geosynthetic reinforced soil foundations.” J. Geotech. Geoenviron. Eng. 123(1), 66–72. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:1(66).
Bishop, A. W. 1959. “The principle of effective stress.” Teknisk Ukeblad 106 (39): 859–863.
Bolton, M. D. 1986. “The strength and dilatancy of sands.” Géotechnique 36 (1): 65–78. https://doi.org/10.1680/geot.1986.36.1.65.
Bolton, M. D., and C. K. Lau. 1989. “Scale effects in the bearing capacity of granular soils.” In Vol. 2 of Proc., 12th Int. Conf. of Soil Mechanics and Foundation Engineering, 895–898. Rio de Janiero, Brazil: A.A. Balkema.
Bolton, M. D., and C. K. Lau. 1993. “Vertical bearing capacity factors on Mohr Coulomb soil.” Can. Geotech. J. 30 (6): 1024–1033. https://doi.org/10.1139/t93-099.
Chen, H. T., C. Lee, and H. Chen. 1998. “The travelling pluviation apparatus for sand sample preparation.” In Vol. 1 of Proc., Centrifuge 98, edited by T. Kimura, O. Kusakabe, and J. Takemura, 143–148. Rotterdam, Netherlands: A.A. Balkema.
Collins, R., and G. A. Miller. 2014. “Cone penetration testing in unsaturated soils at two instrumented test sites.” In Proc., 6th Int. Conf. on Unsaturated Soils. Sydney, Australia: A.A. Balkema.
Consoli, N. C., F. Schnaid, and J. Milititsky. 1998. “Interpretation of plate load tests on residual soil site.” J. Geotech. Geoenviron. Eng. 124 (9): 857–867. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:9(857).
Costa, Y. D., J. C. Cintra, and J. G. Zornberg. 2003. “Influence of matric suction on the results of plate load tests performed on a lateritic soil deposit.” Geotech. Test. J. 26 (2): 219–226.
Cox, A. D. 1962. “Axially symmetric plastic deformations in soils II. Indentation of ponderable soils.” Int. J. Mech. Sci. 4 (5): 371–380. https://doi.org/10.1016/S0020-7403(62)80024-1.
Das, B. M. 2014. Principle of foundation engineering. 8th ed. Boston: Cengage Learning.
Dunnicliff, J. 1988. Geotechnical instrumentation for monitoring field performance. 1st ed. New York: Wiley.
Fretti, C., D. C. E. Lo Presti, and S. Pedroni. 1995. “A pluvial deposition method to reconstitute well-graded sand specimens.” Geotech. Test. J. 18 (2): 292–298. https://doi.org/10.1520/GTJ10330J.
Griffiths, D. V. 1982. “Computation of bearing capacity factors using finite elements.” Géotechnique 32 (3): 195–202. https://doi.org/10.1680/geot.1982.32.3.195.
Hettler, A., and G. Gudehus. 1988. “Influence of the foundation width on the bearing capacity factor.” Soils Found. 28 (4): 81–92. https://doi.org/10.3208/sandf1972.28.4_81.
Khalili, N., and M. H. Khabbaz. 1998. “A unique relationship for χ for the determination of the shear strength of unsaturated soils.” Géotechnique 48 (5): 681–687. https://doi.org/10.1680/geot.1998.48.5.681.
Khalili, N., and S. Zargarbashi. 2010. “Influence of hydraulic hysteresis on effective stress in unsaturated soils.” Géotechnique 60 (9): 729–734. https://doi.org/10.1680/geot.09.T.009.
Khosravi, A., and J. S. McCartney. 2012. “Impact of hydraulic hysteresis on the small-strain shear modulus of low plasticity soils.” J. Geotech. Geoenviron. Eng. 138 (11), 1326–1333. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000713.
Kolbuszewski, J. J. 1948. “An experimental study of the maximum and minimum properties of sands.” In Vol. 1 of Proc., 2nd Int. Conf. of Soil Mechanics and Foundation Engineering, 158–165. Rotterdam, Netherlands.
Lee, J., and R. Salgado. 2000. “Analysis of calibration chamber plate load tests.” Can. Geotech. J. 37 (1): 14–25. https://doi.org/10.1139/t99-061.
Maeda, K., and K. Miura. 1999. “Relative density dependency of mechanical properties of sands.” Soils Found. 39 (1): 69–79. https://doi.org/10.3208/sandf.39.69.
Martin, C. M. 2004. User guide for ABC-analysis of bearing capacity. Oxford, UK: Univ. of Oxford.
Mohamed, F. M. O., and S. K. Vanapalli. 2006. “Laboratory investigations for the measurement of the bearing capacity of an unsaturated coarse grained soil.” Proc., 59th Canadian Geotechnical Conf., 219–226. Vancouver, BC, Canada: Canadian Geotechnical Society.
Nishimura, T., and D. G. Fredlund. 2002. “Hysteresis effects resulting from drying and wetting under relatively dry conditions.” Proc., 3rd Int. Conf. on Unsaturated Soils, 301–305. Lisse, Netherlands: Swets and Zeitlinger.
Oh, W. T., and S. K. Vanapalli. 2011. “Modelling the applied vertical stress and settlement relationship of shallow foundations in saturated and unsaturated sands.” Can. Geotech. J. 48 (3): 425–438. https://doi.org/10.1139/T10-079.
Oh, W. T., and S. K. Vanapalli. 2013. “Interpretation of the bearing capacity of unsaturated fine-grained soil using the modified effective and the modified total stress approaches.” Int. J. Geomech. 13 (6): 769–778. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000263.
Oloo, S. Y. 1994. “A bearing capacity approach to the design of low-volume traffic roads.” Ph.D. thesis, Univ. of Saskatchewan.
Pedroso, D. M. 2015. “A consistent u-p formulation for porous media with hysteresis.” Int. J. Numer. Methods Eng. 101 (8): 606–634. https://doi.org/10.1002/nme.4808.
Poulos, H. G., and A. J. Davids. 2005. “Foundation design for the Emirates Twin Towers, Dubai.” Can. Geotech. J. 42 (3): 716–730. https://doi.org/10.1139/t05-004.
Poulos, H. G., and E. H. Davis. 1974. Elastic solutions for soil and rock mechanics. New York: Wiley.
Pournaghiazar, M., A. R. Russell, and N. Khalili. 2013. “The cone penetration test in unsaturated sands.” Géotechnique 63 (14): 1209–1220. https://doi.org/10.1680/geot.12.P.083.
Reznik, Y. 1994. “A method for interpretation of plate load test results.” Geotech. Test. J. 17 (1): 72–79. https://doi.org/10.1520/GTJ10075J.
Rojas, J. C., L. M. Salinas, and C. Sejas. 2007. “Plate-load tests on an unsaturated lean clay.” Experimental unsaturated soil mechanics, edited by T. Schanz, 445–452. Berlin: Springer.
Russell, A. R. 2010. “Water retention characteristics of soils with double porosity.” Eur J. Soil Sci. 61 (3): 412–424. https://doi.org/10.1111/j.1365-2389.2010.01237.x.
Russell, A. R. 2014. “How water retention in fractal soils depends on particle and pore sizes, shapes, volumes and surface areas.” Géotechnique 64 (5): 379–390. https://doi.org/10.1680/geot.13.P.165.
Russell, A. R., and O. Buzzi. 2012. “A fractal basis for soil-water characteristics curves with hydraulic hysteresis.” Géotechnique 62 (3): 269–274. https://doi.org/10.1680/geot.10.P.119.
Salgado, R., P. Bandini, and A. Karim. 2000. “Shear strength and stiffness of silty sand.” J. Geotech. Geoenviron. Eng. 126 (5): 451–462. https://doi.org/10.1061/(ASCE)1090-0241(2000)126:5(451).
Steenfelt, J. S. 1977. “Scale effect on bearing capacity factor Nγ.” In Vol. 1 of Proc., 9th Int. Conf. of Soil Mechanics and Foundations Engineering, 749–752. Tokyo, Japan: Japanese Society of Soil Mechanics and Foundation Engineering.
Take, W. A., and M. D. Bolton. 2003. “Tensiometer saturation and the reliable measurement of soil suction.” Géotechnique 53 (2): 159–172. https://doi.org/10.1680/geot.2003.53.2.159.
Tan, N. K. 2005. “Pressuremeter and cone penetrometer testing in a calibration chamber with unsaturated Minco silt.” Ph.D. thesis, Univ. of Oklahoma.
Tang, Y., H. A. Taiebat, and A. R. Russell. 2017. “Bearing capacity of shallow foundations in unsaturated soil considering hydraulic hysteresis and three drainage conditions.” Int. J. Geomech. 17 (6): 04016142. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000845.
Vahedifard, F., and J. D. Robinson. 2016. “Unified method for estimating the ultimate bearing capacity of shallow foundations in variably saturated soils under steady flow.” J. Geotech. Geoenviron. Eng. 142 (4): 04015095. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001445.
Vaid, Y. P., and D. Negusey. 1988. “Preparation of reconstituted sand samples.” Advanced triaxial testing of soil and rock, 405–417. Philadelphia: American Society for Testing and Materials.
Vanapalli, S. K., and F. M. O. Mohamed. 2013. “Bearing capacity and settlement of footings in unsaturated sands.” Int. J. Geomate. 5 (1): 595–604.
Vesic, A. S. 1973. “Analysis of ultimate loads of shallow foundations.” J. Soil Mech. Found. Div. 99 (11): 45–73.
Vo, T., and A. R. Russell. 2013. “Unsaturated soil interacting with a rotating model wall.” Int. J. Phys. Model. Geotech. 13 (2): 63–78. https://doi.org/10.1680/ijpmg.12.00014.
Vo, T., and A. R. Russell. 2016. “Bearing capacity of strip footings on unsaturated soils by the slip line theory.” Comput. Geotech. 74: 122–131. https://doi.org/10.1016/j.compgeo.2015.12.016.
Vo, T., H. Taiebat, and A. R. Russell. 2016. “Interaction of a rotating rigid retaining wall with an unsaturated soil in experiments.” Géotechnique 66 (5): 366–377. https://doi.org/10.1680/jgeot.14.P.187.
Wood, F. M., J. A. Yamamuro, and P. V. Lade. 2008. “Effect of depositional method on the undrained response of silty sand.” Can. Geotech. J. 45 (11): 1525–1537. https://doi.org/10.1139/T08-079.
Wuttke, F., B. Kafle, Y. Lins, and T. Schanz. 2013. “Macroelement for statically loaded shallow strip foundation resting on unsaturated soil.” Int. J. Geomech. 13 (5): 557–564. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000254.
Xu, Y. 2004. “Bearing capacity of unsaturated expansive soils.” Geotech. Geol. Eng. 22 (4): 611–625. https://doi.org/10.1023/B:GEGE.0000047043.29898.17.
Yang, H., A. Khoshghalb, and A. R. Russell. 2014. “Fractal-based estimation of hydraulic conductivity from soil-water characteristic curves considering hysteresis.” Géotech. Lett. 4 (1): 1–10. https://doi.org/10.1680/geolett.13.00071.
Yang, H., and A. R. Russell. 2015. “Cavity expansion in unsaturated soils exhibiting hydraulic hysteresis considering three drainage conditions.” Int. J. Numer. Anal. Methods Geomech. 39 (18): 1975–2016. https://doi.org/10.1002/nag.2379.
Yang, H., and A. R. Russell. 2016. “Cone penetration tests in unsaturated silty sands.” Can. Geotech. J. 53 (3): 431–444. https://doi.org/10.1139/cgj-2015-0142.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 144 • Issue 8 • August 2018
Copyright
©2018 American Society of Civil Engineers.
History
Received: May 11, 2017
Accepted: Jan 8, 2018
Published online: May 17, 2018
Published in print: Aug 1, 2018
Discussion open until: Oct 17, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.