Evaluation of Flow Liquefaction and Liquefied Strength Using the Cone Penetration Test
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 136, Issue 6
Abstract
Flow liquefaction is a major design issue for large soil structures such as mine tailings impoundments and earth dams. If a soil is strain softening in undrained shear and, hence, susceptible to flow liquefaction, an estimate of the resulting liquefied shear strength is required for stability analyses. Many procedures have been published for estimating the residual or liquefied shear strength of cohesionless soils. This paper presents cone penetration test-based relationships to evaluate the susceptibility to strength loss and liquefied shear strength for a wide range of soils. Case-history analyses by a number of investigators are reviewed and used with some additional case histories. Extrapolations beyond the case-history data are guided by laboratory studies and theory.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research could not have been carried out without the support, encouragement, and input from John Gregg, Kelly Cabal, and other staff at Gregg Drilling and Testing, Inc.
References
Ahmadi, M. M., and Robertson, P. K. (2005). “Thin layer effects on the CPT qc measurement.” Can. Geotech. J., 42(5), 1302–1317.
Been, K., Crooks, J. H. A., Becker, D. E., and Jefferies, M. G. (1986). “The cone penetration test in sands: Part 1. State parameter interpretation.” Geotechnique, 36(2), 239–249.
Been, K., and Jefferies, M. G. (1985). “A state parameter for sands.” Geotechnique, 35(2), 99–112.
Campanella, R. G., Gillespie, D., and Robertson, P. K. (1982). “Pore pressures during cone penetration testing.” Proc., 2nd European Symp. on Penetration Testing, ESPOT II, Balkema, Rotterdam, The Netherlands, 507–512.
Casagrande, A. (1940). “Characteristics of cohesionless soils affecting the stability of slopes and earth fills.” Contributions to soil mechanics, Boston Society of Civil Engineers, 257–276.
Castro, G. (1969). “Liquefaction of sands.” Harvard soil mechanics series, Vol. 81, Harvard University, Cambridge, Mass.
Castro, G. (1975). “Liquefaction and cyclic mobility of saturated sands.” J. Geotech. Engrg. Div., 101(6), 551–569.
Castro, G., Keller, T. O., and Boynton, S. S. (1989). “Re-evaluation of the Lower San Fernando Dam. Report 1: An investigation of the February 9, 1971 slide.” U.S. Army Corps of Engineers Contract Rep. No. GL-89-2, U.S. Army Corps of Engineers Waterways Experiment Station, Vicksburg, Miss.
Castro, G., Seed, R. B., Keller, T. O., and Seed, H. B. (1992). “Steady state strength analysis of lower San Fernando Dam slide.” J. Geotech. Engrg., 118(3), 406–427.
Cetin, K. O., and Isik, N. S. (2007). “Probabilistic assessment of stress normalization for CPT data.” J. Geotech. Geoenviron. Eng., 133(7), 887–897.
Cetin, K. O., and Ozan, C. (2009). “CPT-based probabilistic soil characterization and classification.” J. Geotech. Geoenviron. Eng., 135(1), 84–107.
Davies, M. P., Dawson, B. D., and Chin, B. G. (1998). “Static liquefaction slump of mine tailings—A case history.” Proc., 51st Canadian Geotechnical Conf., BiTech Publishers, Vancouver, BC, Canada, 123–131.
Davis, A. P., Poulos, S. J., and Castro, G. (1988). “Strengths back figured from liquefaction case histories.” Proc., 2nd Int. Conf. on Case Histories in Geotechnical Engineering, University of Missouri-Rolla, Rolla, Mo., 1693–1701.
Finn, W. D. L. (1981). “Liquefaction potential: Developments since 1976.” Proc., 1st Int. Conf. on Recent Advances in Geotechnical Earthquake Engineering and Soil Dynamics, S. Prakash, ed., University of Missouri-Rolla, Rolla, Mo., 655–681.
Gilstrap, S. D., and Youd, T. L. (1998). “CPT based liquefaction resistance analyses evaluated using case histories.” Technical Rep. No. CEG-98-01, Dept. of Civil and Environmental Engineering, Brigham Young Univ., Provo, Utah.
Idriss, I. M., and Boulanger, R. W. (2004). “Semi-empirical procedures for evaluating liquefaction potential during earthquakes.” Proc., 11th Int. Conf. on Soil Dynamics and Earthquake Engineering, Stallion Press, Tokyo, 32–56.
Idriss, I. M., and Boulanger, R. W. (2007). “SPT- and CPT-based relationships for residual shear strength of liquefied soils.” Proc., 4th Int. Conf. on Earthquake Geotechnical Engineering, K. D. Pitilakis, ed., Springer, New York, 1–22.
Ishihara, K. (1993). “Liquefaction and flow failure during earthquakes.” Geotechnique, 43(3), 351–451.
Jefferies, M. G., and Been, K. (2006). Soil liquefaction—A critical state approach, Taylor and Francis, London.
Jefferies, M. G., and Davies, M. O. (1991). “Soil classification by the cone penetration test: Discussion.” Can. Geotech. J., 28(1), 173–176.
Jefferies, M. G., and Davies, M. P. (1993). “Use of CPTU to estimate equivalent SPT .” Geotech. Test. J., 16(4), 458–468.
Konrad, J. -M., and Watts, B. D. (1995). “Undrained shear strength for liquefaction flow failure analysis.” Can. Geotech. J., 32, 783–794.
Ladd, C. C., Foott, R., Ishihara, K., Schlosser, F., and Poulos, H. G. (1977). “Stress-deformation and strength characteristics: State-of-the-art-report.” Proc., 9th Int. Conf. on Soil Mechanics and Foundation Engineering, Balkema, Tokyo, 421–94.
Leroueil, S., and Hight, D. W. (2003). “Behaviour and properties of natural soils and rocks.” Proc., Int. Conf. on Characterization and Engineering Properties of Natural Soils, Swets and Zeitlinger, Singapore, 29–253.
Leroueil, S., Tavenas, F., and Le Bihan, J. P. (1983). “Propietes charateristiques des argiles de l’est Canada.” Can. Geotech. J., 17(4), 591–602.
Lunne, T., Robertson, P. K., and Powell, J. J. M. (1997). Cone penetration testing in geotechnical practice, Blackie Academic, E & FN Spon/Routledge, New York.
Moss, R. E. S., Seed, R. B., and Olsen, R. S. (2006). “Normalizing the CPT for overburden stress.” J. Geotech. Geoenviron. Eng., 132(3), 378–387.
Olsen, R. S., and Malone, P. G. (1988). “Soil classification and site characterization using the cone penetrometer test.” Penetration Testing 1988, ISOPT-1, J. De Ruiter, ed., Balkema, Rotterdam, The Netherlands, 887–893.
Olson, S. M. (2001). “Liquefaction analysis of level and sloping ground using field case histories and penetration resistance.” Ph.D. thesis, Univ. of Illinois at Urbana–Champaign, Urbana, Ill.
Olson, S. M., and Stark, T. D. (2002). “Liquefied strength ratio from liquefaction flow failure case histories.” Can. Geotech. J., 39, 629–647.
Olson, S. M., and Stark, T. D. (2003). “Yield strength ratio and liquefaction analysis of slopes and embankments.” J. Geotech. Geoenviron. Eng., 129(8), 727–737.
Plewes, H. D., Davies, M. P., and Jefferies, M. G. (1992). “CPT based screening procedure for evaluating liquefaction susceptibility.” Proc., 45th Canadian Geotechnical Conf., Vol. 4, BiTech Publishers, Vancouver, BC, Canada, 1–9.
Popescu, R., Prevost, J. H., and Deodatis, G. (1997). “Effects of spatial variability on soil liquefaction: Some design recommendations.” Geotechnique, 47(5), 1019–1036.
Poulos, S. J., Castro, G., and France, W. (1985). “Liquefaction evaluation procedure.” J. Geotech. Engrg. Div., 111(6), 772–792.
Robertson, P. K. (1990). “Soil classification using the cone penetration test.” Can. Geotech. J., 27(1), 151–158.
Robertson, P. K. (1999). “Estimation of minimum undrained shear strength for flow liquefaction using the CPT.” Proc., 2nd Int. Conf. on Earthquake Geotechnical Engineering, Balkema, Rotterdam, The Netherlands.
Robertson, P. K. (2009a). “Discussion of ‘CPT-based probabilistic soil characterization and classification’ by K. Onder Cetin and Cem Ozan.” J. Geotech. Geoenviron. Eng., 135(1), 84–107.
Robertson, P. K. (2009b). “Interpretation of cone penetration tests—A unified approach.” Can. Geotech. J., 46, 1337–1355.
Robertson, P. K. (2009c). “Performance based earthquake design using the CPT.” Proc., IS Tokyo Conf., CRC Press/Balkema, Taylor & Francis Group, Tokyo.
Robertson, P. K. (2010). “Estimating in situ state parameter in sandy soils from the CPT.” Proc., 2nd Int. Symp. of the Cone Penetration Test, CPT ‘10, Omnipress Publishers, Madison, Wis.
Robertson, P. K., et al. (2000). “The Canadian liquefaction experiment: An overview.” Can. Geotech. J., 37, 499–504.
Robertson, P. K., and Fear, C. E. (1995). “Liquefaction of sands and its evaluation.” IS-Tokyo ‘95, Proc., 1st Int. Conf. on Earthquake Geotechnical Engineering, K. Ishihara, ed., Balkema, Rotterdam, The Netherlands, 1253–1289.
Robertson, P. K., and Wride, C. E. (1998). “Evaluating cyclic liquefaction potential using the CPT.” Can. Geotech. J., 35(3), 442–459.
Schofield, A., and Wroth, C. P. (1968). Critical state soil mechanics, McGraw-Hill, London.
Seed, H. B. (1979). “Soil liquefaction and cyclic mobility evaluation for level ground during earthquakes.” J. Geotech. Engrg. Div., 105(2), 201–255.
Seed, H. B. (1987). “Design problems in soil liquefaction.” J. Geotech. Engrg. Div., 113(8), 827–845.
Seed, H. B., and Harder, L. F. (1990). “SPT-based analysis of cyclic pore pressure generation and undrained residual strength.” Proc., Seed Memorial Symp., BiTech Publishers, Vancouver, BC, Canada, 351–376.
Seed, H. B., Lee, K. L., Idriss, I. M., and Makdisi, F. (1973). “Analysis of the slides in the San Fernando Dams during the earthquake of Feb. 9, 1971.” Earthquake Engineering Research Center Rep. No. EERC 73-2, Univ. of California, Berkeley, Calif.
Seed, H. B., Seed, R. B., Harder, L. F., and Jong, H. -L. (1989). “Reevaluation of the lower San Fernando Dam: Report 2, examination of the post-earthquake slide of February 9, 1971.” U.S. Army Corps of Engineers Contract Rep. No. GL-89-2, U.S. Army Corps of Engineers Waterways Experiment Station, Vicksburg, Miss.
Shuttle, D. A., and Cunning, J. (2007). “Liquefaction potential of silts from CPTu.” Can. Geotech. J., 44, 1–19.
Silvis, F., and de Groot, D. (1995). “Flow slides in the Netherlands: Experience and engineering practice.” Can. Geotech. J., 32, 1086–1092.
Stark, T. D., and Mesri, G. (1992). “Undrained shear strength of sands for stability analysis.” J. Geotech. Engrg. Div., 118(11), 1727–1747.
Terzaghi, K., and Peck, R. B. (1967). Soil mechanics in engineering practice, 1st Ed., Wiley, New York.
Wride, C. E., McRoberts, E. C., and Robertson, P. K. (1999). “Reconsideration of case histories for estimating undrained shear strength in sandy soils.” Can. Geotech. J., 36, 907–933.
Yoshimi, Y., Richart, F. E., Prakash, S., Balkan, D. D., and Ilyichev, Y. L. (1977). “Soil dynamics and its application to foundation engineering.” Proc., 9th Int. Conf. on Soil Mechanics and Foundation Engineering, Balkema, Tokyo, 605–650.
Yoshimine, M., Robertson, P. K., and Wride, C. E. (1999). “Undrained shear strength of clean sands to trigger flow liquefaction.” Can. Geotech. J., 36, 891–906.
Youd, T. L., et al. (2001). “Liquefaction resistance of soils: Summary report from the 1996 NCEER and 1998 NCEER/NSF workshops on evaluation of liquefaction resistance of soils.” J. Geotech. Geoenviron. Eng., 127(4), 297–313.
Zhang, G., Robertson, P. K., and Brachman, R. W. I. (2002). “Estimating liquefaction induced ground settlements from CPT for level ground.” Can. Geotech. J., 39(5), 1168–1180.
Information & Authors
Information
Published In
Copyright
© 2010 ASCE.
History
Received: Jun 2, 2009
Accepted: Nov 17, 2009
Published online: Nov 19, 2009
Published in print: Jun 2010
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.