Numerical Modeling of Cone Penetration Test in Unsaturated Sand inside a Calibration Chamber
Publication: International Journal of Geomechanics
Volume 18, Issue 2
Abstract
Cone-penetration resistance in unsaturated soils may differ from that in dry or saturated soils. A finite-element numerical model simulating the cone penetration process in soil inside a calibration chamber is explained. An arbitrary Lagrangian-Eulerian algorithm was used to overcome the mesh distortion caused by large deformation during penetration. Predicted cone-resistance profiles were validated using calibration-chamber test results and empirical data. Unsaturated soil was modeled using two different approaches: incorporating apparent cohesion in standard constitutive relations and implementing an elastoplastic constitutive model for unsaturated soils. Both approaches resulted in cone-resistance profiles that were in fair agreement with the calibration-chamber data. However, the reasonably successful use of simpler constitutive models with fewer material parameters may be an appropriate option for such applications. Investigations into the effect of degree of saturation on the cone resistance revealed the significant influence of interparticle suction on soil resistance, while they also show that neglecting the saturation effect may lead to unreliable evaluation of soil properties.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abaqus/Explicit [Computer software]. SIMULIA, Providence, RI.
Ahmadi, M. M., Byrne, P. M., and Campanella, R. G. (2005). “Cone tip resistance in sand: Modeling, verification, and applications.” Can. Geotech. J., 42(4), 977–993.
Alonso, E. E., Gens, A., and Josa, A. (1990). “A constitutive model for partially saturated soils.” Géotechnique, 40(3), 405–430.
API (American Petroleum Institute). (1993). “Recommended practice for planning, designing and constructing fixed offshore platforms—Working stress design.” API Recommended Practice 2A-WSD, American Petroleum Institute, Washington, DC.
Arroyo, M., Butlanska, J., Gens, A., Calvetti, F., and Jamiolkowski, M. (2011). “Cone penetration tests in a virtual calibration chamber.” Géotechnique, 61(6), 525–531.
Baldi, G., Bellotti, R., Ghionna, V. N., Jamiolkowski, M., and Lo Presti, D. F. C. (1989). “Modulus of sands from CPTs and DMTs.” Proc., 12th Int. Conf., Soil Mechanics and Foundation Engineering, Vol. 1, A. A. Balkema, Rotterdam, Netherlands, 165–170.
Baldi, G., Bellotti, R., Ghionna, V., Jamiolkowski, M., and Pasqualini, E. (1982). “Design parameters for sand from CPT.” Proc., 2nd European Symp., Penetration Testing, Vol. 2, A. Verruijt, F. L. Beringen, and E. H. De Leeuw, eds., A. A. Balkema, Rotterdam, Netherlands, 425–438.
Baldi, G., Bellotti, R., Ghionna, V., Jamiolkowski, M., and Pasqualini, E. (1986). “Interpretation of CPTs and CPTUs; 2nd part: Drained penetration of sands.” Proc., 4th Int. Geotechnical Seminar: Field Instrumentation and In-Situ Measurements, Nanyang Technological Institute, Singapore, 143–156.
Been, K., Crooks, J. H. A., Becker, D. E., and Jefferies, M. G. (1986). “The cone penetration test in sands: Part I, state parameter interpretation.” Géotechnique, 36(2), 239–249.
Bishop, A. W. (1959). “The principle of effective stress.” Teknisk Ukeblad, 106(39), 859–863.
Bolton, M. D. (1986). “The strength and dilatancy of sands.” Géotechnique, 36(1), 65–78.
Bolton, M. D., et al. (1999). “Centrifuge cone penetration tests in sand.” Géotechnique, 49(4), 543–552.
Butlanska, J., Arroyo, M., and Gens, A. (2010). “Virtual calibration chamber CPT tests on Ticino sand.” Proc., 2nd Int. Symp., Cone Penetration Testing, CPT’10, Vol. 2, P. K. Robertson and P. W. Mayne, eds., CPT'10 Organizing Committee, 217–224.
Butlanska, J., Arroyo, M., Gens, A., and O’Sullivan, C. (2014). “Multi-scale analysis of cone penetration test (CPT) in a virtual calibration chamber.” Can. Geotech. J., 51(1), 51–66.
Calvetti, F., and Nova R. (2005). “Micro-macro relationships from DEM simulated element and in-situ tests.” Proc., 5th Int. Conf., Powders and Grains: Micromechanics of Granular Media, Vol. 1, R. Garcia-Rojo, H. J. Herrmann, and S. McNamara, eds., Taylor & Francis, New York, 245–250.
Falagush, O., McDowell, G. R., and Hai-Sui Yu, D. P. (2015). “Discrete element modeling of cone penetration tests incorporating particle shape and crushing.” Int. J. Geomech., 04015003.
Ghayoomi, M., and McCartney, J. S. (2011). “Measurement of small-strain shear moduli of partially saturated sands during infiltration in a geotechnical centrifuge.” Geotech. Test. J., 34(5), 503–513.
Ghayoomi, M., Suprunenko, G., and Mirshekari, M. (2017). “Cyclic triaxial test to measure strain-dependent shear modulus of unsaturated sand.” Int. J. Geomech., 04017043.
Holmsgaard, R., Nielsen, B. N., and Ibsen, L. B. (2015). “Interpretation of cone penetration testing in silty soils conducted under partially drained conditions.” J. Geotech. Geoenviron. Eng., 04015064.
Hryciw, R., and Dowding, C. H. (1987). “Cone penetration of partially saturated sands.” Geotech. Test. J., 10(3), 135–141.
Huang, A.-B., and Ma, M. Y. (1994). “An analytical study of cone penetration tests in granular material.” Can. Geotech. J., 31(1), 91–103.
Huang, W., Sheng, D., Sloan, S. W., and Yu, H. S. (2004). “Finite element analysis of cone penetration in cohesionless soil.” Comput. Geotech., 31(7), 517–528.
Jamiolkowski, M., Lo Presti, D. C. F., and Manassero, M. (2003). “Evaluation of relative density and shear strength of sands from CPT and DMT.” Soil Behavior and Soft Ground Construction, Geotechnical special publication 119, J. T. Germaine, T. C. Sheahan, and R. V. Whitman, eds., ASCE, Reston, VA, 201–238.
Jamiolkowski, M., Ladd, C. C., Germaine, J. T., and Lancelotta, R. (1985). “New developments in field and laboratory testing of soils.” Proc., 11th Int. Conf., Soil Mechanics and Foundation Engineering, Vol. 1, A. A. Balkema, Rotterdam, Netherlands, 57–153.
Jarast, P., and Ghayoomi, M. (2016). “Simple numerical model to simulate penetration testing in unsaturated soils.” Proc., 3rd European Conf., Unsaturated Soils, E3S Web of Conferences, Vol. 9, EDP Sciences, Paris.
Jiang, M. J., Yu, H.-S., and Harris, D. (2006). “Discrete element modelling of deep penetration in granular soils.” Int. J. Numer. Anal. Methods Geomech., 30(4), 335–361.
Keaveny, J. M., and Mitchell, J. K. (1986). “Strength of fine-grained soils using the piezocone.” Use of In Situ Tests in Geotechnical Engineering, Geotechnical special publication 6, S. P. Clemence, ed., ASCE, New York, 668–685.
Kiousis, P. D., Voyiadjis, G. Z., and Tumay, M. T. (1988). “A large strain theory and its application in the analysis of the cone penetration mechanism.” Int. J. Numer. Anal. Methods Geomech., 12(1), 45–60.
Kouretzis, G. P., Sheng, D., and Wang, D. (2014a). “Numerical simulation of cone penetration testing using a new critical state constitutive model for sand.” Comput. Geotech., 56(Mar), 50–60.
Kouretzis, G. P., Sheng, D., and Wang, D. (2014b). “Numerical simulation of CPT cone penetration in sand.” Appl. Mech. Mater., 553, 416–421.
Kulhawy, F. H., and Mayne, P. H. (1990). “Manual on estimating soil properties for foundation design.” EPRI EL-6800, Project 1493-6, Cornell Univ., Ithaca, NY.
Lehane, B. M., Ismail, M. A., and Fahey, M. (2004). “Seasonal dependence of in situ test parameters in sand above the water table.” Géotechnique, 54(3), 215–218.
Loret, B., and Khalili, N. (2002). “An effective stress elastic–plastic model for unsaturated porous media.” Mech. Mater., 34(2), 97–116.
Lu, N., and Likos, W. J. (2006). “Suction stress characteristic curve for unsaturated soil.” J. Geotech. Geoenviron. Eng., 131–142.
Markauskas, D., Kacianauskas, R., and Šukšta, M. (2002). “Modelling the cone penetration test by the finite element method.” Found. Civ. Environ. Eng., 2, 125–140.
Mayne, P. W. (1991). “Determination of OCR in clays by piezocone tests using cavity expansion and critical state concepts.” Soils Found., 31(2), 65–76.
Nazem, M., Sheng, D., and Carter, J. P. (2006). “Stress integration and mesh refinement for large deformation in geomechanics.” Int. J. Numer. Methods Eng., 65(7), 1002–1027.
Pournaghiazar, M., Russell, A. R., and Khalili, N. (2011). “Development of a new calibration chamber for conducting cone penetration tests in unsaturated soils.” Can. Geotech. J., 48(2), 314–321.
Pournaghiazar, M., Russell, A. R., and Khalili, N. (2012). “Linking cone penetration resistances measured in calibration chambers and the field.” Géotechnique Lett., 2(2), 29–35.
Pournaghiazar, M., Russell, A. R., and Khalili, N. (2013). “The cone penetration test in unsaturated sands.” Géotechnique, 63(14), 1209–1220.
Robertson, P. K. (2009). “Interpretation of cone penetration tests—A unified approach.” Can. Geotech. J., 46(11), 1337–1355.
Robertson, P. K., and Campanella, R. G. (1983). “Interpretation of cone penetration tests. Part I: Sand.” Can. Geotech. J., 20(4), 718–733.
Roscoe, K. H., and Burland, J. B. (1968). “On the generalised stress–strain behaviour of ‘wet’ clay.” Engineering plasticity, J. Heyman and F. A. Leckie, eds., Cambridge University Press, Cambridge, U.K., 535–609.
Russell, A. R., and Khalili, N. (2004). “A bounding surface plasticity model for sands exhibiting particle crushing.” Can. Geotech. J., 41(6), 1179–1192.
Russell, A. R., and Khalili, N. (2006a). “On the problem of cavity expansion in unsaturated soils.” Comput. Mech., 37(4), 311–330.
Russell, A. R., and Khalili, N. (2006b). “A unified bounding surface plasticity model for unsaturated soils.” Int. J. Numer. Anal. Methods Geomech., 30(3), 181–212.
Sheng, D., Nazem, M., and Carter, J. P. (2009). “Some computational aspects for solving deep penetration problems in geomechanics.” Comput. Mech., 44(4), 549–561.
Susila, E., and Hryciw, R. D. (2003). “Large displacement FEM modelling of the cone penetration test (CPT) in normally consolidated sand.” Int. J. Numer. Anal. Methods Geomech., 27(7), 585–602.
Vanapalli, S. K., and Mohamed, F. M. O. (2013). “Bearing capacity and settlement of footings in unsaturated sands.” Int. J. GEOMATE, 5(1), 595–604.
van den berg, P. (1994). “Analysis of soil penetration.” Ph.D. thesis, Delft University Press, Delft, Netherlands.
Yang, H., and Russell, A. R. (2016). “Cone penetration tests in unsaturated silty sands.” Can. Geotech. J., 53(3), 431–444.
Yi, J. T., Goh, S. H., Lee, F. H., and Randolph, M. F. (2012). “A numerical study of cone penetration in fine-grained soils allowing for consolidation effects.” Géotechnique, 62(8), 707–719.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 18 • Issue 2 • February 2018
Copyright
© 2017 American Society of Civil Engineers.
History
Received: Oct 9, 2016
Accepted: Aug 4, 2017
Published online: Dec 6, 2017
Published in print: Feb 1, 2018
Discussion open until: May 6, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.