Effects of Injection Parameters on the Combustion and Emission Characteristics of Diesel-Piloted Direct-Injection Natural Gas Engine during Idle Conditions
Publication: Journal of Energy Engineering
Volume 141, Issue 4
Abstract
The purpose of this paper is to investigate the effects of injection parameters on combustion and emission characteristics of a six-cylinder diesel-piloted direct-injection natural gas engine at idle conditions. The tests were conducted at three injection pressures (15, 18, and 24 MPa), two different injection intervals (0.7 and 1.0 ms), and start of natural gas injection in the range of 4–13° before top dead center (BTDC). The experimental results revealed that in terms of cylinder pressure and heat release rate, the maximum cylinder pressure and the maximum heat release rate were substantially higher at the injection pressure of 24 MPa and increased gradually with advanced injection timing, while only slightly influenced by injection interval. In terms of combustion parameters, the ignition delay was reduced by adoption of higher injection pressure and the rapid combustion duration was extended more evidently with the advance of injection timing. In terms of emissions, application of relatively lower injection pressure of 15 and 18 MPa had benefits in reduction of CO, HC, and emissions; CO emissions were higher with advanced injection timing and could be improved with shorter injection interval at the injection pressure of 15 and 18 MPa, while emissions exhibited the same trend for all injection pressures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers acknowledge financial support from Ministry of Industry and Information Technology of the People’s Republic of China (2060303), and assistance from Weichai Westport Inc. in conducting the experiments.
References
Abd-Alla, G. H., Soliman, H. A., Badr, O. A., and Abd Rabbo, M. F. (2002). “Effect of injection timing on the performance of a dual fuel engine.” Energy. Covers. Manage., 43(2), 269–277.
Abdelaal, M. M., and Hegab, A. H. (2012). “Combustion and emission characteristics of a natural gas-fueled diesel engine with EGR.” Energy. Covers. Manage., 64(12), 301–312.
Benajes, J., Molina, S., Garci, J., and Novella, R. (2004). “Influence of boost pressure and injection pressure on combustion process and exhaust emissions in a HD diesel engine.”, Warrendale, PA.
Carlucci, A. P., Ficarella, A., and Laforgia, D. (2014). “Potentialities of a common rail injection system for the control of dual fuel biodiesel-producer gas combustion and emission.” J. Energy Eng., A4014011.
Chiu, J. P., Wegrzyn, J., and Murphy, K. E. (2004). “Low emissions class 8 heavy-duty on-highway natural gas and gasoline engine.”, Warrendale, PA.
Cho, H. M., and He, B. Q. (2006). “Spark ignition natural gas engines—A review.” Energy. Covers. Manage., 48(2), 608–618.
Dodge, L., Simescu, S., Nealy, G., Maymar, M., Dickey, D., and Savonen, C. (2002). “Effect of small holes and high pressure on diesel engine combustion.”, Warrendale, PA.
Goudie, D., et al. (2004). “Development of a compression ignition heavy duty pilot-ignited natural gas fuelled engine for low emissions.”, Warrendale, PA.
Harrington, J., Munshi, S. R., Nedelcu, C., Ouellette, P., Thompson, J., and Whitfield, S. (2002). “Direct injection of natural gas in a heavy-duty diesel engine.”, Warrendale, PA.
Hill, P. G., and Ouellette, P. (1999). “Transient turbulent gaseous fuel jets for diesel engines.” J. Fluids Eng., 121(1), 93–101.
Korakianitis, T., Namasivayam, A. M., and Crookes, R. J. (2011). “Natural-gas fueled spark-ignition (SI) and compression-ignition (CI) engine performance and emissions.” Prog. Energy Combust. Sci., 37(1), 89–112.
McTaggart-Cowan, G. P. (2006). “Pollutant formation in a gaseous-fuelled, direct injection engine.” Ph.D. thesis, Univ. of British Columbia, Vancouver, Canada.
McTaggart-Cowan, G. P., Bushe, W. K., Hill, P. G., and Munshi, S. R. (2003a). “A supercharged heavy-duty diesel sing-cylinder research engine for high-pressure direct injection of natural gas.” Int. J. Eng. Res., 4(4), 315–330.
McTaggart-Cowan, G. P., Bushe, W. K., Rogak, S. N., Hill, P. G., and Munshi, S. R. (2003b). “Injection parameter effects on a direct injected, pilot ignited, heavy duty natural gas engine with EGR.”, Warrendale, PA.
Munshi, S. R., McTaggart-Cowan, G. P., Huang, J., and Hill, P. G. (2011). “Development of a partially-premixed combustion strategy for a low-emission, direct injection high efficiency natural gas engine.” Proc., Internal Combustion Engine Div. Fall Technical Conf., ASME, New York.
Naber, J. D., Siebers, D. I., Julio, D., and Westbrook, C. K. (1994). “Effects of natural gas composition on ignition delay under diesel conditions.” Combust. Flame, 99(2), 192–200.
Nakagawa, K., Sakurai, T., and Shoji, F. (1998). “Study of lean burn gas engines using pilot fuel for ignition source.”, Warrendale, PA.
Ouellette, P. (2008). “Direct injection of natural gas for diesel engine fueling.” Ph.D. thesis, Univ. of British Columbia, Vancouver, Canada.
Papagiannakis, R. G., Hountalas, D. T., Rakopoulos, C. D., and Rakopoulos, D. C. (2008). “Combustion and performance characteristics of a DI diesel engine operating from low to high natural gas supplement ratios at various operating conditions.”, Warrendale, PA.
Peter, M. (1996). “Pilot-ignited natural gas combustion in diesel engines.” Ph.D. thesis, Univ. of British Columbia, Vancouver, Canada.
Rakopoulos, C. D., Rakopoulos, D. C., Giakoumis, E. G., and Dimaratos, A. M. (2010). “Investigation of the combustion of neat cottonseed oil or its neat bio-diesel in a HSDI diesel engine by experimental heat release and statistical analyses.” Fuel, 89(12), 3814–3826.
Rakopoulos, D. C., Rakopoulos, C. D., Giakoumis, E. G., and Dimaratos, A. M. (2013). “Studying combustion and cyclic irregularity of diethyl ether as supplement fuel in diesel engine.” Fuel, 109(7), 325–335.
Rente, T., Gjirja, S., and Denbratt, I. (2004). “Experimental investigation of the effect of needle opening (NOP) pressure on combustion and emissions formation in a heavy duty DI diesel engine.”, Warrendale, PA.
Singh, S., Krishnan, S. R., Srinivasan, K. K., Midkiff, K. C., and Bell, S. R. (2004). “Effect of pilot injection timing, pilot quantity, and intake charge conditions on performance and emissions for an advanced low-pilot-ignited natural gas engine.” Int. J. Eng. Res., 5(4), 330–348.
Sullivan, G. S., Huang, J., Wang, T. X., Bush, T. K., and Rogak, S. N. (2005). “Emissions variability in gaseous fuel direct injection compression ignition combustion.”, Warrendale, PA.
Woschni, G. (1967). “A universally applicable equation for the instantaneous heat transfer coefficient in the internal combustion engine.”, Warrendale, PA.
Zeng, K., et al. (2006). “Combustion characteristics of a direct-injection natural gas engine under various fuel injection timings.” Appl. Therm. Eng., 26(8–9), 806–813.
Zhang, F., Okamoto, K., Morimoto, S., and Shoji, F. (1998). “Methods of increasing the BMEP (power output) for natural gas spark ignition engines.”, Warrendale, PA.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jun 24, 2014
Accepted: Aug 13, 2014
Published online: Sep 11, 2014
Discussion open until: Feb 11, 2015
Published in print: Dec 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.