Elastic Fracture Toughness of Ductile Materials
Publication: Journal of Engineering Mechanics
Volume 143, Issue 9
Abstract
Linear elastic fracture mechanics has been widely used for fracture analysis of cracked metals. For ductile materials, it is known that the yielding of a crack front results in the easing of stress intensity at the crack front, which ultimately increases the total fracture toughness of the material. Therefore, to use linear elastic fracture mechanics for prediction of the failure of ductile materials requires the extraction of the elastic portion of the fracture toughness. The intention of this paper is to develop a new theory of fracture toughness for ductile materials. Two methods, namely the elastic-plastic parameter method and the failure assessment diagram method, are proposed to determine the elastic fracture toughness. After verification of derived models, the developed elastic fracture toughness theory is applied to ductile metal pipes. Factors that affect the elastic fracture toughness are also studied in the paper. It is found in this study that the elastic fracture toughness is a function of the geometry of cracked bodies, material properties, loading conditions, and mode mixity. The developed theory of elastic fracture toughness will enable accurate prediction of the fracture conditions for both brittle and ductile metals, which is essential to prevent catastrophic failures of structures made of ductile metals.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support from the Australian Research Council under DP140101547, LP150100413, and DP170102211 is gratefully acknowledged.
References
ABAQUS version 6.11 [Computer software]. Dassault Systèmes Simulia Corp., Providence, RI.
Al-Laham, A. (1999). “Stress intensity factor and limit load handbook.”, British Energy, London.
Anderson, T. L., (1991). Fracture mechanics: Fundamentals and applications, CRC Press, Boca Raton, FL.
API/ASME. (2016). “Fit-for-service: ASME/API joint committee on fitness-for-service policies and procedures.”, Washington, DC.
ASTM. (2014). “Standard test method for measurement of fracture toughness.” ASTM E1820-13, West Conshohocken, PA.
BSI (British Standards Institution). (2013). “Guide to methods for assessing the acceptability of flaws in metallic structures.”, London.
Chang, J., Xu, J. Q., and Mutoh, Y. (2006). “A general mixed-mode brittle fracture criterion for cracked materials.” Eng. Fract. Mech., 73(9), 1249–1263.
Feng, X., Kumar, A. M., and Hirth, J. P., (1993). “Mixed mode I/III fracture toughness of 2034 aluminum alloys.” Acta Metall. Mater., 41(9), 2755–2764.
Fu, G. Y., Yang, W., and Li, C. Q. (2017). “Stress intensity factors for mixed mode fracture induced by inclined cracks in pipes under axial tension and bending.” Theor. Appl. Fract. Mech., 89, 100–109.
Hallbäck, N. (1997). “Mixed-mode I/II fracture behavior of a high strength steel.” Int. J. Fract., 87(4), 363–388.
Kamat, A. M., Hirth, J. P., Hoagland, R., and Feng, X. X. (1994). “A suggested test procedure to measure mixed mode I-III fracture toughness of brittle materials.” J. Test. Eval., 22(4), 327–334.
Kamat, S. V., and Hirth, J. P. (1995). “Mixed mode fracture toughness of engineering materials.” J. Eng. Mater. Technol., 117(4), 391–394.
Kamat, S. V., and Hirth, J. P. (1996). “Mixed mode I/II fracture toughness of 2034 aluminum alloys.” Acta Materialia, 44(1), 201–208.
Keiichiro, T., and Hitoshi, I., (1992). “Elastic-plastic fracture toughness test under mixed mode I-II loading.” Eng. Fract. Mech., 41(4), 529–540.
Kim, Y. J., Shim, D. J., Huh, N. S., and Kim, Y. J. (2002). “Plastic limit pressures for cracked pipes using finite element limit analyses.” Int. J. Pressure Vessels Piping, 79(5), 321–330.
Kim, Y. J., Shim, D. J., Huh, N. S., and Kim, Y. J. (2003). “Finite element based plastic limit loads for cylinders with part-through surface cracks under combined loading.” Int. J. Pressure Vessels Pip., 80(7–8), 527–540.
Li, C. Q., Fu, G. Y., and Yang, W. (2016). “Stress intensity factors for inclined external surface cracks in pressurized pipes.” Eng. Fract. Mech., 165, 72–86.
Li, C. Q., Fu, G. Y., Yang, W., and Yang, S. T. (2017). “Derivation of elastic fracture toughness for ductile metal pipes with circumferential external cracks under combined tension and bending.” Eng. Fract. Mech., 178, 39–49.
Li, H. X., Jones, R. H., Hirth, J. P., and Gelles, D. S. (1995). “Effect of loading mode on the fracture toughness of a ferritic/martensitic stainless steel.” Metall. Mater. Trans. A, 26(9), 2259–2267.
Liu, S., Chao, Y. J., and Zhu, X., (2004). “Tensile-shear transition in mixed mode I/III fracture.” Int. J. Solids Struct., 41(22–23), 6147–6172.
Manoharan, M., Hirth, J. P., and Rosenfield, A. R. (1990). “A suggested procedure for combined mode I–mode III fracture toughness testing.” J. Test. Eval., 18(2), 106–114.
Miller, A. G. (1988). “Review of limit loads of structures containing defects.” Int. J. Pressure Vessels Piping, 32(1–4), 197–327.
Milne, I., Ainsworth, R. A., Dowling, A. R., and Stewart, A. T. (1988). “Assessment of the integrity of structures containing defects.” Int. J. Pressure Vessels Piping, 32(1–4), 3–104.
Murakami, Y. (1987). Stress intensity factors handbook, Elsevier, Amsterdam, Netherlands.
Paradkar, A. G., and Kamat, S. V. (2011). “Fracture toughness of Ti-15Al–8Nb alloy under mixed mode I/III loading.” Mater. Sci. Eng. A, 528(9), 3283–3288.
Pirondi, A., and Dalle Donne, C. (2001). “Characterization of ductile mixed-mode fracture with the crack-tip displacement vector.” Eng. Fract. Mech., 68(12), 1385–1402.
Raghavachary, S., Rosenfield, A. R., and Hirth, J. P. (1990). “Mixed mode I/III fracture toughness of an experimental rotor steel.” Metall. Trans. A, 21(9), 2539–2545.
Raju, I. S., and Newman, J. C. (1982). “Stress-intensity factors for internal and external surface cracks in cylindrical vessels.” J. Pressure Vessel Technol. Trans. ASME, 104(4), 293–298.
Raju, I. S., and Newman, J. C. (1986). “Stress intensity factors for circumferential surface cracks in pipes and rods under tension and bending loads.” ASTM STP 905, ASTM, West Conshohocken, PA, 789–805.
Richard, H. A., (1989). Specimens for investigating biaxial fracture and fatigue processes, Mechanical Engineering Publications, London, 217–229.
Richard, H. A., and Benitz, K. (1983). “A loading device for the creation of mixed mode in fracture mechanics.” Int. J. Fract., 22(2), R55–R58.
Richard, H. A., Eberlein, A., and Schirmeisen, N. H. (2013). “Experiments on cracks under spatial loading.” 13th Int. Conf. on Fracture, Curran Associates, Inc., New York.
Richard, H. A., and Kuna, M. (1990). “Theoretical and experimental study of superimposed fracture modes I, II and III.” Eng. Fract. Mech., 35(6), 949–960.
Riks, E. (1979). “An incremental approach to the solution to the solution of buckling and snapping problems.” Int. J. Solids Struct., 15(7), 529–551.
Saka, M., and Tanaka, S. (1986). “Stain and stress fields near the blunted tip of a crack under mixed mode loading and the implication for fracture.” Mech. Mater., 5(4), 331–338.
Shih, C. F. (1974). “Small-scale yielding analysis of mixed mode plane strain crack problem.” ASTM STP, 560, 187–210.
SINTAP. (1999). “Structural integrity assessment procedures for European industry—Final procedure.”, Rotherham, U.K.
Srinivas, M., Kamat, S. V., and Rama Rao, P. (2004). “Influence of mixed mode I/III loading on fracture toughness of mild steel at various strain rates.” Mater. Sci. Technol., 20(2), 235–242.
Tada, H., Paris, P. C., and Irwin, G. R. (2000). The stress analysis of cracks handbook, 3rd Ed., ASME, New York.
Yang, S. T., Li, C. Q., and Yang, W. (2016). “Analytical model of elastic fracture toughness for steel pipes with internal cracks.” Eng. Fract. Mech., 153, 50–60.
Zhu, X. K., and Joyce, J. A. (2012). “Review of fracture toughness (G, K, J, CTOD, CTOA) testing and standardization.” Eng. Fract. Mech., 85, 1–46.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Nov 4, 2016
Accepted: Mar 23, 2017
Published online: Jul 14, 2017
Published in print: Sep 1, 2017
Discussion open until: Dec 14, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.