Grit Removal from Wastewater Using Secondary Currents in Open-Channel Flow around Bends
Publication: Journal of Environmental Engineering
Volume 137, Issue 11
Abstract
A grit removal process that exploits the phenomenon of secondary currents induced in open-channel flow as water moves around a bend has been investigated by using both physical and computational fluid dynamics (CFD) modeling approaches. The flow field was first validated against a case study by solving the full Reynolds-averaged Navier-Stokes equations and Reynolds stress turbulence models with a finite-volume method. The air-water interaction at the free surface was simulated by using a volume of fluid multiphase model. Discrete phase modeling was then used to calibrate the hydrodynamic interaction with grit particles (varying in size from 63 to 2,000 µm) observed in a physical model with a 30° bend, with respect to particle diameter, flow rate, shape factor, and injection location. This was followed by detailed parametric investigations using the calibrated model at different flow rates, angle of bend, and radius of curvature that showed individual particle trajectories (and consequent grit removal efficiency of the process) for different particle sizes. The CFD model was also used to compare different configurations of receiving sump whereby different outflows and baffles were compared. Overall, the study shows that a very slightly curved channel or straight channel is, in fact, the optimum solution, because the secondary currents in curved channels act to uplift particles away from the sump, thus reducing grit removal efficiency.
Get full access to this article
View all available purchase options and get full access to this article.
References
Adamsson, A., Stovin, V. R., and Bergdahl, L. (2003). “Bed shear stress boundary condition for storage tank sedimentation.” J. Environ. Eng., 129(7), 651–658.
Alkhaddar, R. M., Higgins, P. R., Phipps, D. A., and Andoh, R. Y. G. (2001). “Residence time distribution of a model hydrodynamic vortes separator.” Urban Water, 3(1-2), 17–24.
Annen, G. W. (1972). “Efficiency of a grit chamber.” Water Res., 6(4), 393–394.
Ashley, R. M., et al. (2003). “The utilisation of engineered invert traps in the management of near bed solids in sewer networks.” Water Sci. Technol., 47(4), 137–148.
Bathurst, J. C., Thorne, C. R., and Hey, R. D. (1979). “Secondary flow and shear stress at bends.” J. Hydraul. Div., 105, 1277–1295.
Blanckaert, K. (2003). “Flow and turbulence in sharp open channel bends.” Ph.D. thesis, EPFL, Laussane, Switzerland.
Blanckaert, K., Buschman, F. A., Schielen, R., and Wijbenga, J. H. A. (2008). “Redistribution of velocity and bed-shear stress in straight and curved open channels by means of a bubble screen: Laboratory experiments.” J. Hydrol. Eng., 134(2), 184–195.
Blanckaert, K., and Graf, W. H. (2001). “Mean flow and turbulence in open-channel bend.” J. Hydrol. Eng., 127(10), 835–847.
Booij, R. (2003). “Measurements and large eddy simulations of the flows in some curved flumes.” J. Turbul., 4, 1–17.
British Standards Institute (BSI). (1990). “Methods of test for soils for civil engineering purposes.” General requirements and sample preparation, BS1377, London.
Buxton, A., Tait, S., Stovin, V. R., and Saul, A. (2002). “Developments in a methodology for the design of engineered grit traps in combined sewer networks.” Water Sci. Technol., 45(7), 133–142.
Chanson, H. (1999). The hydraulics of open channel flow: An introduction, Arnold Publishers, London.
Chen, D., and Duan, J. G. (2006). “Modeling width adjustment in meandering channels.” J. Hydrol. (Amsterdam), 321(1-4), 59–76.
Cokljat, D., and Younis, A. (1995). “Second-order closure study of open-channel flows.” J. Hydrol. Eng., 121(2), 94–107.
Duan, G., Wang, S. S. Y., and Jia, Y. (2001). “The applications of enhanced CCHE2D model to study the alluvial channel migration process.” J. Hydraul. Res., 39(5), 469–480.
Dufresne, M., Vazquez, J., Terfous, A., Ghenaim, A., and Poulet, J.-B. (2009). “Experimental investigation and CFD modelling of flow, sedimentation and solids separation in a combined sewer detention tank.” Comput. Fluids, 38(5), 1042–1049.
Egarr, D. A., Faram, M. G., O’Doherty, T., and Syred, N. (2004). “An investigation into the factors that determine the efficiency of a hydrodynamic vortex separator.” Sustainable Techniques and Strategies in Urban Water Management (NOVATECH 2004), F. Brelot, B. Chocat, and M. Desbordes, eds., International Water Association, London.
Faram, M. G., and Harwood, R. (2003). “A method for the numerical assessment of sediment interceptors.” Water Sci. Technol., 47(4), 167–174.
Fluent. (2006). Fluent user manual Version 6.2., ANSYS, Inc., Canonsburg, PA.
Harwood, R., and Saul, A. J. (2001). “Modelling the performance of combined-sewer overflow chambers.” Water Environ. J., 15(4), 300–304.
Hicks, F. E., Jin, Y. C., and Steffler, P. M. (1990). “Flow near sloped bank in curved channel.” J. Hydrol. Eng., 116(1), 55–70.
Hirt, C. W., and Nichols, B. D. (1981). “Volume of fluid (VOF) method for the dynamics of free boundaries.” J. Comput. Phys., 39(1), 201–225.
Jayanti, S., and Narayanan, S. (2004). “Computational study of particle-eddy interaction in sedimentation tanks.” J. Environ. Eng., 130(1), 37–49.
Kang, H., and Choi, S.-U. (2006). “Reynolds stress modelling of rectangular open-channel flow.” Int. J. Numer. Methods Fluids, 51(11), 1319–1334.
Khosronejad, A., Rennie, C., Salehi Neyshabouri, S. A. A., and Townsend, R. A. (2007). “3D numerical modeling of flow and sediment in laboratory channel bends.” J. Hydrol. Eng., 133(10), 1123–1134.
Launder, B. E., Reece, G. J., and Rodi, W. (1975). “Progress in the development of Reynolds stress turbulence closure.” J. Fluid Mech., 68(3), 537–566.
Launder, B. E., and Spalding, D. B. (1974). “The numerical computation of turbulent flows.” Int. J. Comput. Methods Eng. Sci. Mech., 3, 269–289.
Ma, L, Ashworth, P. J., Best, J. L., Elliot, L., Ingham, D. B., and Whitcombe, L. J. (2002). “Computational fluid dynamics and the physical modeling of an upland urban river.” Geomorphology, 44(3-4), 375–391.
Marais, G. V. R., and van Haandel, A. C. (1996). “Design of grit channels controlled by Parshall flumes.” Water Sci. Technol., 33(3), 195–210.
Metcalf and Eddy, Inc. (2003). Wastewater engineering—Treatment, disposal and reuse, 4th Ed., Tchobanoglous, G., Burton, F. L., and Stensel, H. D., eds., McGraw-Hill, New York.
Naot, D., Nezu, I., and Nakagawa, H. (1993). “Hydrodynamic behaviour of compound rectangular open channels.” J. Hydrol. Eng., 3, 390–408.
Nezu, I. (2005). “Open-channel flow turbulence and its research prospect in the 21st century.” J. Hydrol. Eng., 4, 229–246.
Nicholas, A. P. (2001). “Computational fluid dynamics modeling of boundary roughness in gravel-bed rivers: An investigation of the effects of random variability in bed elevation.” Earth Surf. Processes Landforms, 26, 346–362.
NWW Engineering. (1995). Tech. Rep.—Biddulph Bendy channel report, Warrington, UK.
Patankar, S. V. (1980). Numerical heat transfer and fluid flow, Taylor and Francis Group, New York.
Patel, T. (2007). “A study on hydrodynamics of grit particles in curved open channels using physical and computational modelling.” Ph.D. thesis, Trinity College, Dublin, Ireland.
Rameshwaran, P., and Naden, P. S. (2004a). “Modeling turbulent flow in two-stage meandering channels.” Proc. ICE Water Manage., 157(3), 159–173.
Rameshwaran, P., and Naden, P. S. (2004b). “Three-dimensional modeling of free surface variation in a meandering channel.” J. Hydraul. Res., 42(6), 603–615.
Rameshwaran, P., and Shiono, K. (2002). “Predictions of velocity and boundary shear stress in compound meandering channels.” Proc., River Flow 2002, Int. Conf. on Fluvial Hydraulics, Bousmar, D., and Zech, Y., eds., Swets and Zeitlinger, Netherlands, 223–231.
Rameshwaran, P., and Shiono, K. (2003). “Computer modelling of two-stage meandering channel flows.” Proc. ICE Water Marit. Energy, 156(4), 773–788.
Rhee, S. H. (2005). “Unstructured grid based Reynolds-Averaged Navier-Stokes method for liquid tank sloshing.” J. Fluids Eng., 127(3), 572–582.
Senocak, I., and Iaccarino, G. (2005). “Progress towards RANS simulation of free-surface flow around modern ships.” Annual Research Briefs, Center of Turbulent Research, Stanford Univ., Stanford, CA, 151–156.
Stovin, V. R., and Saul, A. J. (1996). “Efficiency prediction for storage chambers using computational fluid dynamics.” Water Sci. Technol., 33(9), 163–170.
Stovin, V. R., and Saul, A. J. (1998). “A computational fluid dynamics (CFD) particle technique approach to efficiency prediction.” Water Sci. Technol., 37(1), 285–293.
Stovin, V. R., and Saul, A. J. (2000). “Computational fluid dynamics and design of sewage storage chambers.” Water Environ. J., 14(2), 103–110.
Ye, J., and McCorquodale, J. A. (1998). “Simulation of curved open channel flows by 3D hydrodynamic model.” J. Hydrol. Eng., 124(7), 687–698.
Information & Authors
Information
Published In
Journal of Environmental Engineering
Volume 137 • Issue 11 • November 2011
Pages: 1026 - 1039
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Mar 2, 2010
Accepted: Apr 6, 2011
Published online: Apr 8, 2011
Published in print: Nov 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.