Sociotechnical Evaluation of the Soft Story Problem in Reinforced Concrete Frame Buildings in Nepal
Publication: Journal of Performance of Constructed Facilities
Volume 35, Issue 4
Abstract
In urban and semiurban areas of Nepal, it is a common practice that the construction of reinforced-concrete (RC) framed buildings with infill masonry have open ground floor as commercial shutter and a parking lot while the upper floor contains infill masonry for residential purposes. A reduction in a story’s infill relative to the ones above increases inelastic deformation on the columns of that story and causes soft story collapse of the open floor. In the 2015 Gorkha earthquake, the number of human casualties in RC buildings and economic loss exposed the deficiencies associated with RC. Although numerous studies have recommended solutions to soft story problems, there is still a lack of practical implementation at the ground level. In this paper, the Applied element method (AEM) was used to analyze the efficiency and applicability of existing solutions to soft story problems in Nepal using and social survey using web questionnaire to understand the social aspects of the soft story problem. Results of this research showed that, although technically there are some retrofitting methods that could solve soft story problems, the large number of existing buildings with soft stories—compounded by low awareness, unstable economic conditions, lack of locally available raw materials, and resistance to closing businesses run in the open story design—render eradicating the problem socially incapable.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or codes supporting the findings of this study are available from the corresponding authors upon reasonable request.
References
Altin, S., Ö. Anil, and M. E. Kara. 2008. “Strengthening of RC nonductile frames with RC infills: An experimental study.” Cem. Concr. Compos. 30 (7): 612–621. https://doi.org/10.1016/j.cemconcomp.2007.07.003.
Altin, S., U. Ersoy, and T. Tamkut. 1992. “Hysteretic response of reinforced-concrete infilled frames.” J. Struct. Eng. 118 (8): 2133–2150. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:8(2133).
Antonopoulos, T. A., and S. A. Anagnostopoulos. 2010. “Optimum partial strengthening for improved seismic performance of old reinforced concrete buildings with open ground story.” In Advances in performance-based earthquake engineering, 395–404. Dordrecht, Netherlands: Springer.
Antonopoulos, T. A., and S. A. Anagnostopoulos. 2012. “Seismic evaluation and upgrading of RC buildings with weak open ground stories.” Earthquakes Struct. 3 (3–4): 611–628. https://doi.org/10.12989/eas.2012.3.3_4.611.
Badoux, M., and J. O. Jirsa. 1990. “Steel bracing of RC frames for seismic retrofitting.” J. Struct. Eng. 116 (1): 55–74. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:1(55).
Bulgarian Seismic Code. 1987. Code for design of buildings and structures in seismic regions. Sofia, Bulgaria: Bulgarian Academy of Science Committee of Territorial and Town System at the Council of Ministers.
CBS (Central Bureau of Statistics). 2012. National population and housing census 2011. Kathmandu, Nepal: Government of Nepal, National Planning Commission, CBS.
CEN (European Committee for Standardization). 2005. Eurocode 8: Design of structures for earthquake resistance—Part 1: General rules, seismic actions and rules for buildings. EN 1998-1:2004. Brussels, Belgium: CEN.
Chai, Y. H., M. N. Priestley, and F. Seible. 1991. “Seismic retrofit of circular bridge columns for enhanced flexural performance.” Struct. J. 88 (5): 572–584.
Chaulagain, H., H. Rodrigues, E. Spacone, and H. Varum. 2015. “Assessment of seismic strengthening solutions for existing low-rise RC buildings in Nepal.” Earthquakes Struct. 8 (3): 511–539. https://doi.org/10.12989/eas.2015.8.3.511.
Davis, R., P. Krishnan, D. Menon, and A. M. Prasad. 2004. “Effect of infill stiffness on seismic performance of multistory RC framed buildings in India.” In Proc., 13th World Conf. on Earthquake Engineering. Tokyo: International Association for Earthquake Engineering.
Di Trapani, F., M. Malavisi, G. C. Marano, A. P. Sberna, and R. Greco. 2020. “Optimal seismic retrofitting of reinforced concrete buildings by steel-jacketing using a genetic algorithm-based framework.” Eng. Struct. 219 (Sep): 110864. https://doi.org/10.1016/j.engstruct.2020.110864.
Dixit, A. M. 2004. “Promoting safer building construction in Nepal.” In Proc., 13th World Conf. on Earthquake Engineering. Tokyo: International Association for Earthquake Engineering.
Erdem, I., U. Akyuz, U. Ersoy, and G. Ozcebe. 2006. “An experimental study on two different strengthening techniques for RC frames.” Eng. Struct. 28 (13): 1843–1851. https://doi.org/10.1016/j.engstruct.2006.03.010.
Fardis, M. N., and T. B. Panagiotakos. 1997. “Seismic design and response of bare and masonry-infilled reinforced concrete buildings. Part II: Infilled structures.” J. Earthquake Eng. 1 (3): 475–503.
Foo, S., N. Naumoski, and M. Saatcioglu. 2001. Seismic hazard, building codes and mitigation options for Canadian buildings. Ottawa: Office of Critical Infrastructure Protection and Emergency Preparedness.
Gautam, D., H. Rodrigues, K. K. Bhetwal, P. Neupane, and Y. Sanada. 2016. “Common structural and construction deficiencies of Nepalese buildings.” Innovative Infrastruct. Solutions 1 (1): 1–18. https://doi.org/10.1007/s41062-016-0001-3.
Greek Code. 2000. Greek code for seismic resistant structures. Athens, Greece: Organization of Seismic Resistant Planning and Protection.
Hall, J. F., W. Holmes, and P. Somers. 1994. Northridge earthquake, January 17, 1994. Oakland, CA: Earthquake Engineering Research Institute.
Ilki, A., A. Tezcan, V. Koc, and N. Kumbasar. 2004. “Seismic retrofit of non-ductile rectangular reinforced concrete columns by CFRP jacketing”. In Proc., 13th World Conf. of Earthquake Engineering. Vancouver, BC: International Association for Earthquake Engineering.
Indian Standard. 2002. Criteria for earthquake resistant design of structures: Part I. Delhi, India: Bureau of Indian Standards.
Inel, M., and E. Meral. 2016. “Seismic performance of RC buildings subjected to past earthquakes in Turkey.” Earthquakes Struct. 11 (3): 483–503. https://doi.org/10.12989/eas.2016.11.3.483.
Israel Standard. 1995. Design provisions for earthquake resistance of structures. Tel-Aviv, Israel: The Standards Institution of Israel.
JICA (Japan International Cooperation Agency). 2002. The study on Earthquake disaster mitigation in the Kathmandu Valley. Tokyo: Japan International Cooperation Agency and Ministry of Home Affairs.
Kaushik, H. B., D. C. Rai, and S. K. Jain. 2009. “Effectiveness of some strengthening options for masonry-infilled RC frames with open first story.” J. Struct. Eng. 135 (8): 925–937. https://doi.org/10.1061/(ASCE)0733-9445(2009)135:8(925).
Kawamata, S., and M. Ohnuma. 1981. “Strengthening effect of eccentric steel braces to existing reinforced concrete frames.” In Proc., 7th World Conf. of Earthquake Engineering. Tokyo: International Association for Earthquake Engineering.
Lagaros, N. D., and M. A. Geraki. 2008. “The effects of construction practices on the seismic performance of RC frames with masonry infills.” Struct. Eng. Mech. 28 (1): 69–88. https://doi.org/10.12989/sem.2008.28.1.069.
Lee, H.-S., and S.-W. Woo. 2002. “Effect of masonry infills on seismic performance of a 3-story R/C frame with non-seismic detailing.” Earthquake Eng. Struct. Dyn. 31 (2): 353–378. https://doi.org/10.1002/eqe.112.
Lee, J. Y., Y. J. Oh, J. S. Park, and M. Mansour. 2004. “Behaviors of concrete columns with both spiral and fiber composites.” In Proc., 13th World Conf. of Earthquake Engineering. Tokyo: International Association for Earthquake Engineering.
Maekawa, K., H. Okamura, and A. Pimanmas. 2003. Non-linear mechanics of reinforced concrete. Boca Raton, FL: CRC Press.
Makran, S. 2001. Preliminary observations on the origin and effects of the January 26, 2001 Bhuj (Gujarat, India) earthquake. Oakland, CA: Earthquake Engineering Research Institute (EERI) Newsletter.
Matsuzaki, Y., K. Nakano, S. Fujii, and H. Fukuyama. 2000. “Seismic retrofit using continuous fiber sheets.” In Proc., 12th World Conf. of Earthquake Engineering. Tokyo: International Association for Earthquake Engineering.
Meguro, K. 2008. “Promotion of seismic retrofitting for existing low earthquake resistant structures: The most important issue for earthquake disaster reduction.” In Vol. 8 of cSUR-UT series: Library for sustainable urban regeneration, 29–74. Berlin: Springer. https://doi.org/10.1007/978-4-431-78149-3.
Meguro, K., and H. Tagel-Din. 2000. “Applied element method for structural analysis.” Doboku Gakkai Ronbunshu 2000 (647): 31–45. https://doi.org/10.2208/jscej.2000.647_31.
Michailidis, C., A. Kappos, and K. Stylianidis. 1997. Irregularities in the seismic response of RC buildings due to the presence of masonry infills. Southampton, UK: Computational Mechanics Publications.
Mousavi, M. M. R., and A. R. Khaloo. 2011. “Effect of steel plate jacketing of columns in seismic behavior of concrete beam-column connections.” In Proc., 6th National Congress on Civil Engineering. Semnan, Iran: Semnan Univ.
Negro, P., and G. Verzeletti. 1996. “Effect of infills on the global behaviour of R/C frames: Energy considerations from pseudodynamic tests.” Earthquake Eng. Struct. Dyn. 25 (8): 753–773. https://doi.org/10.1002/(SICI)1096-9845(199608)25:8%3C753::AID-EQE578%3E3.0.CO;2-Q.
Nepal Survey Department. 2020. Political and administrative map of Nepal. Kathmandu, Nepal: Government of Nepal, Ministry of Land Management, Cooperation and Poverty Alleviation.
NSET (National Society for Earthquake Technology). 2009. Seismic vulnerability evaluation guideline for private and public buildings. Part—1: Pre-disaster vulnerability assessment. Kathmandu, Nepal: Government of Nepal, Ministry of Physical Planning and Works.
Ozturkoglu, O., T. Ucar, and Y. Yesilce. 2017. “Effect of masonry infill walls with openings on nonlinear response of reinforced concrete frames.” Earthquakes Struct. 12 (3): 333–347. https://doi.org/10.12989/eas.2017.12.3.333.
Parajuli, Y. K., J. K. Bothara, A. M. Dixit, J. P. Pradhan, and R. Sharpe. 2000. “Nepal building code-need, development philosophy and means of implementation.” In Proc., 12th World Conf. on Earthquake Engineering. Tokyo: International Association for Earthquake Engineering.
Pokharel, T., and H. M. Goldsworthy. 2017. “Lessons learned from the Nepal earthquake 2015.” Aust. J. Struct. Eng. 18 (1): 11–23. https://doi.org/10.1080/13287982.2017.1309818.
Priestley, M. N., F. Seible, and Y. Xiao. 1994a. “Steel jacket retrofitting of reinforced concrete bridge columns for enhanced shear strength—Part 2: Test results and comparison with theory.” Struct. J. 91 (5): 537–551.
Priestley, M. N., F. Seible, Y. Xiao, and R. Verma. 1994b. “Steel jacket retrofitting of reinforced concrete bridge columns for enhanced shear strength—Part 1: Theoretical considerations and test design.” Struct. J. 91 (4): 394–405.
Sahoo, D. R., and D. C. Rai. 2013. “Design and evaluation of seismic strengthening techniques for reinforced concrete frames with soft ground story.” Eng. Struct. 56 (Nov): 1933–1944 https://doi.org/10.1016/j.engstruct.2013.08.018.
Seible, F., M. N. Priestley, G. A. Hegemier, and D. Innamorato. 1997. “Seismic retrofit of RC columns with continuous carbon fiber jackets.” J. Compos. Constr. 1 (2): 52–62https://doi.org/10.1061/(ASCE)1090-0268(1997)1:2(52).
Siddiqui, U. A., H. Sucuoglu, and A. Yakut. 2015. “Seismic performance of gravity-load designed concrete frames infilled with low-strength masonry.” Earthquakes Struct. 8 (1): 19–35. https://doi.org/10.12989/eas.2015.8.1.019.
Tagel-Din, H. 1998. “A new efficient method for nonlinear, large deformation and collapse analysis of structures.” Ph.D. dissertation, Dept. of Civil Engineering, The Univ. of Tokyo.
Timsina, K., C. K. Gadagamma, and K. Meguro. 2019. “A comprehensive field study to examine the complications in soft storey problem in Nepal.” Seisan Kenkyu 71 (6): 1059–1063.
Varum, H., R. Dumaru, A. Furtado, A. R. Barbosa, D. Gautam, and H. Rodrigues. 2018. “Seismic performance of buildings in Nepal after the Gorkha earthquake.” In Impacts and insights of Gorkha earthquake in Nepal, 47–63. Amsterdam, Netherlands: Elsevier.
Yang, X., W. Yuan, G. Chen, and L. Fan. 2000. “Seismic performance assessment and retrofit of rectangular bridge piers with externally encased circular steel jackets.” In Proc., 12th World Conf. of Earthquake Engineering. Tokyo: International Association for Earthquake Engineering.
Ye, L. P., K. Zhang, S. H. Zhao, and P. Feng. 2003. “Experimental study on seismic strengthening of RC columns with wrapped CFRP sheets.” Constr. Build. Mater. 17 (6–7): 499–506. https://doi.org/10.1016/S0950-0618(03)00047-3.
Yon, B., E. Sayin, Y. Calayir, Z. C. Ulucan, M. Karatas, H. Sahin, K. E. Alyamac, and A. T. Bildik. 2015. “Lessons learned from recent destructive Van, Turkey earthquakes.” Earthquakes Struct. 9 (2): 431–453. https://doi.org/10.12989/eas.2015.9.2.431.
Zou, X. K., J. G. Teng, L. De Lorenzis, and S. H. Xia. 2007. “Optimal performance-based design of FRP jackets for seismic retrofit of reinforced concrete frames.” Composites, Part B. 38 (5–6): 584–597. https://doi.org/10.1016/j.compositesb.2006.07.016.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: May 8, 2020
Accepted: Dec 17, 2020
Published online: Apr 19, 2021
Published in print: Aug 1, 2021
Discussion open until: Sep 19, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.