Contribution of Transverse Tie Bars to Load Transfer in Adjacent Prestressed Box-Girder Bridges with Partial Depth Shear Key
Publication: Journal of Performance of Constructed Facilities
Volume 31, Issue 2
Abstract
Adjacent box-girder bridges have become a popular choice as they can be constructed quickly, easily, and economically. In spite of their good performance during many years of service, one major problem has been recurrent longitudinal cracking of the grout material in the shear key. A combination of shear keys and transverse posttensioning (TPT) ties in such kind of bridges is typically used to connect the bridge girders together so that they would behave as a single integrated unit. However, information regarding the contribution of the TPT tie bars on load transfer between adjacent box girders is limited. In this study, a single-span precast prestressed concrete adjacent box-girder bridge was instrumented and monitored to study the effect of TPT tie bars on load transfer mechanism and overall bridge behavior under static and dynamic truck loads. Two sets of instruments were installed in the girders and tie bars during and after the construction of the bridge. A good correlation was achieved between experimental measurements and results from a three-dimensional (3D) finite element (FE) model. An in-depth analysis of the data indicated that, under static loads, there was a contribution from the tie bars to the load-transfer mechanism between the girders. The maximum measured relative displacement at the joints was below the damage limits. Under dynamic loading, the dynamic load allowance (DLA) obtained was higher than that of the standard design procedure of bridges. Based on the FE analysis, the relative displacement of the joints and the load distribution between the girders are influenced by the initial TPT force applied during construction. The level of stresses generated in the concrete girders and shear keys under truck load was not high enough to cause damage.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO and LRFD (Load and Resistance Factor Design). (2012). Bridge design specifications, 6th Ed., Washington, DC.
ABAQUS 6.12-3 [Computer software]. Dassault Systèmes Simulia, Providence, RI.
ACI (American Concrete Institute). (2011). “Building code requirements for structural concrete and commentary.” ACI 318 R-11, Farmington Hills, MI.
ASTM. (2004). “Standard test method for splitting tensile strength of cylindrical concrete specimens.” ASTM C496/C496M-11, West Conshohocken, PA.
ASTM. (2014). “Standard test method for compressive strength of cylindrical concrete specimens.” ASTM C39/C39M-14a, West Conshohocken, PA.
Badwan, I. Z., and Liang, R. Y. (2007). “Performance evaluation of precast posttensioned concrete multibeam deck.” J. Perform. Constr. Facil., 368–374.
Deng, L., Yu, Y., Zou, Q., and Cai, C. S. (2014). “State-of-the-art review of dynamic impact factors of highway bridges.” J. Bridge Eng., .
El-Remaily, A., Tadros, M. K., Yamane, T., and Krause, G. (1996). “Transverse design of adjacent prestressed concrete box-girder bridges.” PCI J., 41(4), 96–113.
Engström, B., ed. (2008). Structural connections for precast concrete buildings, Vol. 6, International Federation of Structural Concrete, Lausanne, Switzerland.
Fu, C. C., Pan, Z., and Ahmed, M. S. (2011). “Transverse posttensioning design of adjacent precast solid multibeam bridges.” J. Perform. Constr. Facil., 223–230.
Grace, N., Jensen, E., and Noamesi, D. (2011). “Flexural performance of carbon fiber-reinforced polymer prestressed concrete side-by-side box-beam bridge.” J. Compos. Constr., 663–671.
Grace, N. F., Jensen, E., Matsagar, V., Bebawy, M., Soliman, E., and Hanson, J. (2008). “Use of unbonded CFCC for transverse post-tensioning of side-by-side box-beam bridges.”, Dept. of Civil Engineering, Lawrence Technological Univ., Southfield, MI.
Grace, N. F., Jensen, E. A., and Bebawy, M. R. (2012). “Transverse post-tensioning arrangement for side-by-side box-beam bridges.” PCI J., 57(2), 48–63.
Hanna, K. E., Morcous, G., and Tadros, M. K. (2009). “Transverse post-tensioning design and detailing of precast, prestressed concrete adjacent-box-girder bridges.” PCI J., 54(4), 159–174.
Hillerborg, A., Modéer, M., and Petersson, P. E. (1976). “Analysis of crack formation and crack growth in concrete by means of fracture mechanics and finite elements.” Cem. Concr. Res., 6(6), 773–781.
Huckelbridge, A. A., Jr., El-Esnawi, H., and Moses, F. (1995). “Shear key performance in multibeam box-girder bridges.” J. Perform. Constr. Facil., 271–285.
Hussein, H. H., Walsh, K. K., Sargand, S. M., and Steinberg, E. P. (2016). “Interfacial properties of ultrahigh-performance concrete and high-strength concrete bridge connections.” J. Mater. Civ. Eng., 04015208.
Julio, E. N., Branco, F. A., and Silva, V. D. (2004). “Concrete-to-concrete bond strength. Influence of the roughness of the substrate surface.” Constr. Build. Mater., 18(9), 675–681.
Lall, J., Alampalli, S., and DiCocco, E. F. (1998). “Performance of full depth shear keys in adjacent prestressed box-beam bridges.” PCI J., 43(2), 72–79.
Lee, J., and Fenves, G. L. (1998). “Plastic-damage model for cyclic loading of concrete structures.” J. Eng. Mech., 892–900.
Lubliner, J., Oliver, J., Oller, S., and Onate, E. (1989). “A plastic-damage model for concrete.” Int. J. Solids Struct., 25(3), 299–326.
ODOT (Ohio Department of Transportation). (2013). “Ohio construction and material specifications.” Office of Structural Engineering, Columbus, OH.
PCI (Precast/Prestressed Concrete Institute). (2011). PCI bridge design manual, 3rd Ed., Chicago.
Russell, H. G. (2009). Adjacent precast concrete box-beam bridges: Connection details, Vol. 393, Transportation Research Board, Washington, DC.
Russell, H. G. (2011). “Adjacent precast concrete box-beam bridges: State of the practice.” PCI J., 56(1), 75–91.
Steinberg, E., Huffman, J., Ubbing, J., and Giraldo-Londoño, O. (2013). “Finite element modeling of adjacent prestressed concrete box-beams.” Proc., PCI National Bridge Conf., Precast/Prestressed Concrete Institute, Chicago.
Ulku, E., Attanayake, U., and Aktan, H. M. (2010). “Rationally designed staged posttensioning to abate reflective cracking on side-by-side box-beam bridge decks.” Transp. Res. Rec., 2172(1), 87–95.
Information & Authors
Information
Published In
Journal of Performance of Constructed Facilities
Volume 31 • Issue 2 • April 2017
Copyright
©2016 American Society of Civil Engineers.
History
Received: Apr 12, 2016
Accepted: Sep 13, 2016
Published online: Oct 25, 2016
Discussion open until: Mar 25, 2017
Published in print: Apr 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.