Reliability Analysis of RC Columns and Frame with FRP Strengthening Subjected to Explosive Loads
Publication: Journal of Performance of Constructed Facilities
Volume 30, Issue 2
Abstract
Some structures, both military and civilian, might experience explosive loads during their service life. Owing to high uncertainties in blast load predictions and structural parameters, accurate assessment of the performances of structures under explosion loads is a challenging task. For example, a number of experimental studies using fiber-reinforced plastic (FRP) strengthening of RC structures have been reported in the literature. Most of these studies demonstrate that FRP strengthening is effective in increasing the blast load–carrying capacities of RC structures. However, significant variations in the effectiveness of FRP strengthening have also been observed owing to the large uncertainties in blast loading, RC and FRP material properties, and workmanship in preparing the test specimens and conducting experimental tests. Very few studies that take into consideration these uncertainties in analyzing the effectiveness of FRP strengthening of RC structures on blast loading resistance can be found in the literature. This study performs a reliability analysis to assess the performance of RC columns with or without FRP strengthening in resisting blast loads. Statistical variations of blast loading predictions derived in a previous study are adopted in this study. To define structural performance, pressure-impulse () curves with a damage criterion on the basis of axial load-carrying capacity that were developed in previous studies for RC columns without strengthening or with FRP strip, FRP wrap, or both FRP strip and wrap strengthening are used. Considering the uncertainties in blast loading predictions and RC column and FRP material properties and dimensions, limit-state functions corresponding to different damage levels of RC columns with or without FRP strengthening are formulated. The statistical variations of blast loading, RC column dimension, longitudinal and transverse reinforcement ratio, and concrete, steel, and FRP material strength and FRP thickness are considered. The failure probabilities of RC columns corresponding to different damage levels with or without FRP strengthening are calculated. The effectiveness of FRP strengthening on the RC column’s blast loading resistance capacities is discussed. The importance of considering the random fluctuations on blast loading and RC column parameters in assessing the blast loading effect on RC columns is demonstrated. A structural system reliability analysis is also carried out to examine the probability of structural collapse as a result of blast loading applied to the front of an example two-span multistory RC frame. The results obtained in this study demonstrate the effectiveness of FRP strengthening on structure protection and can also be used to assess RC structure performance under blast loadings.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge support from the Australian Research Council and University of Western Australia final-year student Thomas Nyman. The third author also acknowledges the financial support from the China National Nature Science Foundation (Grant Number 51008209) and Tianjin Nature Science Foundation (Grant Number 12JCQNJC04800) for supporting this research.
References
Atadero, R., and Karbhari, V. (2005). “Probabilistic based design for FRP strengthening of reinforced concrete.” Proc., 7th Int. Symp. Fiber-Reinforced Polymer Reinforcement for Concrete Structures, Special Publication SP-230, American Concrete Institute, Farmington Hills, MI.
Baker, W. E., and Cox, P. (1983). Explosion hazards and evaluation, Elsevier Scientific, Amsterdam, Netherlands.
Beckmann, B., Hummeltenberg, A., Weber, T., and Curbach, M. (2011). “Concrete under high strain rates: Local material and global structure response to impact loading.” Int. J. Protective Struct., 2(3), 283–294.
Bogosian, D., Ferritto, J., and Shi, Y. (2002). “Measuring uncertainty and conservatism in simplified blast models.” 30th Explosive Safety Seminar, Atlanta.
Britt, J. R., Ranta, D. E., and Joachim, C. E. (2001). “BlastX code, version 4.2, user’s manual.”, U.S. Army Engineer Research and Development Center, Vicksburg, MS.
Brode, H. L. (1959). “Blast wave from a spherical charge.” Phys. Fluids, 2(2), 217–229.
Buchan, P. A., and Chen, J. F. (2007). “Blast resistance of FRP composites and polymer strengthened concrete and masonry structures—A state-of-the-art review.” Composites Part B, 38(5–6), 509–522.
Connolly, J. P. (1976). “Construction tolerances in reinforced concrete beams/joists.” ACI J. Proc., 73(11), 613–617.
Crawford, J. E., Malvar, L. J., Dunn, B. W., and Gee, D. J. (1996). “Retrofit of reinforced concrete columns using composite wraps to resist blast effects.” Karagozian and Case, Glendale, CA.
Crawford, J. E., Malvar, L. J., Morrill, K. B., and Ferritto, J. M. (2001). “Composite retrofits to increase the blast resistance of reinforced concrete buildings.” Proc., 10th Int. Symp. on Interaction of the Effects of Munitions with Structures, Woodhead Publishing, Sawston, Cambridge.
Ellingwood, B. (1978). “Reliability basis of load and resistance factors for reinforced concrete design.”, U.S. Dept. of Commerce, National Bureau of Standards, Washington, DC.
FEMA. (2003). “Reference manual to mitigate potential terrorist attacks against buildings.” Risk management series, Washington, DC.
Hao, H., Stewart, M., Li, Z.-X., and Shi, Y. (2010). “RC column failure probabilities to blast loads.” Int. J. Protective Struct., 1(4), 571–591.
Henrych, J. (1979). Dynamics of explosion and its use, Elsevier Scientific, Amsterdam, Netherlands.
Hyde, D. (1992). ConWep—Application of TM5-855-1, Structural Mechanics Division, Structures Laboratory, U.S. Army Corps of Engineers Waterway Experimental Station, Vicksburg, MS.
Isaac, P., Darby, A., Ibell, T., and Evernden, M. (2011). “Plasticity based approach for evaluating the blast response of RC columns retrofitted with FRP.” Int. J. Protective Struct., 2(3), 367–380.
Khalifa, A., Alkhrdaji, T., Nanni, A., and Lansburg, S. (1999). “Anchorage of surface mounted FRP reinforcement.” Concr. Int., 21(10), 49–54.
Kingery, C. N., and Bulmash, G. (1984). “Air blast parameters from TNT spherical air burst and hemispherical surface burst.” Ballistic Research Laboratories, Aberdeen Proving Ground, MD.
Lawver, D., Daddazio, R., Oh, G. J., Lee, C. K. B., Pifko, A. B., and Stanley, M. (2003). “Simulating the response of composite reinforced floor slabs subjected to blast loading.” Proc., ASME 2003 Int. Mechanical Engineering Congress and Exposition: Applied Mechanics and Biomedical Technology, ASME, New York.
Liu, P. L., Der Kiureghian, A., and Lin, H. Z. (1989). CALREL user manual, Dept. of Civil Engineering, Univ. of California, Berkeley, CA.
Low, H. Y., and Hao, H. (2001). “Reliability analysis of reinforced concrete slabs under explosive loading.” Struct. Saf., 23(2), 157–178.
Low, H. Y., and Hao, H. (2002). “Reliability analysis of direct shear and flexural failure modes of RC slabs under explosive loading.” Eng. Struct., 24(2), 189–198.
MacGregor, J. G., Mirza, S., and Ellingwood, B. (1983). “Statistical analysis of resistance of reinforced and prestressed concrete members.” ACI J. Proc., 80(3), 167–176.
Mirza, S. A., MacGregor, J. G., and Hatzinikolas, M. (1979). “Statistical descriptions of strength of concrete.” J. Struct. Div., 105(6), 1021–1037.
Mosalam, K. M., and Mosallam, A. S. (2001). “Nonlinear transient analysis of reinforced concrete slabs subjected to blast loading and retrofitted with CFRP composites.” Composites Part B, 32(8), 623–636.
Muszynski, L., and Purcell, M. (2003a). “Composite reinforcement to strengthen existing concrete structures against air blast.” J. Compos. Constr., 93–97.
Muszynski, L., and Purcell, M. (2003b). “Use of composite reinforcement to strengthen concrete and air-entrained concrete masonry walls against air blast.” J. Compos. Constr., 98–108.
Mutalib, A. A., and Hao, H. (2011). “Development of P-I diagrams for FRP strengthened RC columns.” Int. J. Impact Eng., 38(5), 290–304.
Netherton, M., and Stewart, M. (2010). “Blast load variability and accuracy of blast load prediction models.” Int. J. Protective Struct., 1(4), 543–570.
Razaqpur, G. A., Tolba, A., and Contestabile, E. (2007). “Blast loading response of reinforced concrete panels reinforced with externally bonded GFRP laminates.” Composites Part B, 38(5–6), 535–546.
Sadovskii, M. A. (1952). Mechanical effects of air shock waves from explosions according to experiments, Izd Akaud Nauk SSSR, Moscow.
Shi, Y., Hao, H., and Li, Z.-X. (2008). “Numerical derivation of pressure–impulse diagrams for prediction of RC column damage to blast loads.” Int. J. Impact Eng., 35(11), 1213–1227.
Standards Association of Australia. (2002). “Structural design actions.” AS1170, Sydney, NSW, Australia.
Standards Association of Australia. (2009). “Concrete structures.” AS3600, Sydney, NSW, Australia.
Stewart, M. G. (2006). “Risk assessment and optimization of blast mitigation strategies for design and strengthening of built infrastructure.” Trans. Tianjin Univ., 12(z1), 8–15.
Stewart, M. G. (2010). “Acceptable risk criteria for infrastructure protection.” Int. J. Protective Struct., 1(1), 23–40.
Stewart, M. G., and Melchers, R. E. (1997). Probabilistic risk assessment of engineering systems, Chapman & Hall, London.
Stewart, M. G., and Netherton, M. D. (2005). “Blast reliability curves and uncertainty modelling for glazing subject to explosive blast loading.” Proc., 6th Asian-Pacific Conf. on Shock and Impact Loads on Structures, CI-Premier, Singapore.
Teng, J., Chen, J., Smith, S., and Lam, L. (2003). “Behaviour and strength of FRP-strengthened RC structures: A state-of-the-art review.” Proc. ICE Struct. Build., 156(1), 51–62.
Teychenne, D. C. (1966). “The variability of the concrete and its treatment in codes of practice.” Struct. Concr., 3(1), 33–47.
Triantafillou, T. C. (1998). “Strengthening of structures with advanced FRPs.” Prog. Struct. Eng. Mater., 1(2), 126–134.
Twisdale, L. A., Sues, R. H., and Lavelle, F. M. (1994). “Reliability-based design methods for protective structures.” Struct. Saf., 15(1–2), 17–33.
U.S. Department of Defence (DoD). (2008). “Structures to resist the effects of accidental explosion.”, Washington, DC.
U.S. Department of State (DOS). (2009). Country reports on terrorism 2008, Washington, DC.
U.S. Department of State (DOS). (2011). Country reports on terrorism 2010, Washington, DC.
U.S. Department of the Army. (1969). “Structures to resist the effects of accidental explosion.”, Arlington, VA.
U.S. Department of the Army. (1990). “Design of structures to resist the effects of accidental explosions.”, Arlington, VA.
Val, D., Bljuger, F., and Yankelevsky, D. (1997). “Reliability assessment of damaged RC framed structures.” J. Struct. Eng., 889–895.
Wager, P. (2005). SHOCK user’s manual version 1.0, Engineering Service Center, Port Hueneme, CA.
Wang, N., Ellingwood, B., and Zureick, A. (2010). “Reliability-based evaluation of flexural members strengthened with externally bonded fiber-reinforced polymer composites.” J. Struct. Eng., 1151–1160.
Wang, Y., Lin, F., and Gu, X. (2011). “Load and resistance factors for progressive collapse resistance design of reinforced concrete building structures.” Adv. Mater. Res., 338–344.
Wu, C., Oehlers, D. J., Rebentrost, M., Leach, J., and Whittaker, A. S. (2009). “Blast testing of ultra-high performance fibre and FRP-retrofitted concrete slabs.” Eng. Struct., 31(9), 2060–2069.
Zhou, X. Q., Kuznetsov, V. A., Hao, H., and Waschl, J. (2008). “Numerical prediction of concrete slab response to blast loading.” Int. J. Impact Eng., 35(10), 1186–1200.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Jul 23, 2014
Accepted: Dec 26, 2014
Published online: Mar 12, 2015
Discussion open until: Aug 12, 2015
Published in print: Apr 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.