Fatigue Behavior of UHPC Beams Prestressed with External CFRP Tendons
Publication: Journal of Composites for Construction
Volume 26, Issue 5
Abstract
This paper presents an experimental investigation of the fatigue behavior of ultrahigh-performance concrete (UHPC) beams prestressed with external carbon fiber-reinforced polymer (CFRP) tendons. Seven T-shaped beams were tested, and the effects of the effective prestressing stress, partial prestressing ratio, and fatigue load level on the flexural behavior and stiffness were analyzed and presented. Overall, the CFRP tendon–anchor assembly exhibited excellent fatigue performance. All tested fully prestressed beams survived 2 million cycles in fatigue tests, and the variation in their flexural capacity was limited. The partially prestressed beam failed after approximately 97,200 cycles due to fatigue fracture of the internal reinforcement. After fracture of the tensile steel bars, the partially prestressed beam behaved similarly to the fully prestressed beam and sustained more than half of the flexural capacity after 2 million cycles. A higher effective prestressing stress was favorable for maintaining the stiffness of CFRP prestressed UHPC beams.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research described herein was sponsored by the National Natural Science Foundation of China (Project ID 51938012). The authors also acknowledge the colleagues in the Key Laboratory of Wind and Bridge Engineering of Hunan Province at Hunan University for their technical support.
Notation
The following symbols are used in this paper:
- Ap
- area of the CFRP tendon;
- As
- area of tensile steel bars;
- Bf
- stiffness after a number of fatigue cycles;
- Bs
- stiffness before fatigue test;
- d
- nominal diameter of a wire of CFRP tendons;
- D
- nominal diameter of CFRP tendons;
- de
- effective diameter of a wire of CFRP tendons;
- Ec
- elasticity modulus of UHPC;
- fc
- axial compressive strength of UHPC;
- fcu
- cubic compressive strength of UHPC;
- ffp
- tensile strength of the CFRP tendon;
- fpe
- effective prestressing stress in the CFRP tendon;
- fy
- yield strength of the tensile steel bar;
- N
- loading cycles of beams;
- Nf
- fatigue life of beams;
- Pcr
- cracking load of beams under static loading;
- Pmax
- upper limit of fatigue load;
- Pmin
- lower limit of fatigue load;
- Ps
- softening load of fully prestressed beams under static loading;
- Pu
- ultimate load of beams under static loading;
- Pu,pf
- ultimate load of beams in the postfatigue static test;
- Py
- yielding load deflection of partially prestressed beams under static loading;
- R
- fatigue load range;
- Rf
- fatigue load level;
- Δcr
- cracking midspan deflection of beams under static loading;
- Δfatigue
- midspan deflection of beams under the upper limit of fatigue load after a number of fatigue cycles;
- Δs
- softening midspan deflection of fully prestressed beams under static loading;
- Δstatic
- midspan deflection under the upper limit before the fatigue test;
- Δu
- ultimate midspan deflection of beams under static loading;
- Δu,pf
- ultimate midspan deflection of beams in the postfatigue static test;
- Δy
- yielding midspan deflection of partially prestressed beams under static loading;
- Δσs
- stress range in tensile steel bars;
- θ
- stiffness reduction coefficient of the beams;
- ρs
- longitudinal reinforcement ratio;
- ρsv
- shear reinforcement ratio;
- σs,max
- maximum stress in the tensile steel bars; and
- σs,min
- minimum stress in the tensile steel bars.
References
AASHTO. 2017. AASHTO LRFD bridge design specifications. 8th ed. AASHTO LRFD-8. Washington, DC: AASHTO.
ACI (American Concrete Institute). 1997. Considerations for design of concrete structures subjected to fatigue loading. ACI 215R-74. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2015. Guide for the design and construction of structural concrete reinforced with fiber-reinforced polymer (FRP) bars. ACI 440.1R-15. Farmington Hills, MI: ACI.
Au, F. T. K., and J. S. Du. 2008. “Deformability of concrete beams with unbonded FRP tendons.” Eng. Struct. 30 (12): 3764–3770. https://doi.org/10.1016/j.engstruct.2008.07.003.
Bakis, C. E., L. C. Bank, V. L. Brown, E. Cosenza, J. F. Davalos, J. J. Lesko, A. Machida, S. H. Rizkalla, and T. C. Triantafillou. 2002. “Fiber-reinforced polymer composites for construction—State-of-the-art review.” J. Compos. Constr. 6 (2): 73–87. https://doi.org/10.1061/(ASCE)1090-0268(2002)6:2(73).
Braimah, A., M. F. Green, and T. I. Campbell. 2006. “Fatigue behaviour of concrete beams post-tensioned with unbonded carbon fibre reinforced polymer tendons.” Can. J. Civ. Eng. 33 (9): 1140–1155. https://doi.org/10.1139/l06-063.
CSA (Canadian Standards Association). 2012. Design and construction of building structures with fiber-reinforced polymers. CAN/CSA-S806-12. Rexdale, ON, Canada: CSA.
Dogu, M., and F. Menkulasi. 2020. “A flexural design methodology for UHPC beams posttensioned with unbonded tendons.” Eng. Struct. 207: 110193. https://doi.org/10.1016/j.engstruct.2020.110193.
Du, Y., J. Wei, J. Yuan, Y. Lai, and D. Sun. 2020. “Experimental research on fatigue behavior of prestressed concrete beams under constant-amplitude and variable-amplitude fatigue loading.” Constr. Build. Mater. 259: 119852. https://doi.org/10.1016/j.conbuildmat.2020.119852.
El Meski, F., and M. Harajli. 2015. “Evaluation of the flexural response of CFRP-strengthened unbonded posttensioned members.” J. Compos. Constr. 19 (3): 04014052. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000516.
Elrefai, A., J. S. West, and K. Soudki. 2007. “Performance of CFRP tendon-anchor assembly under fatigue loading.” Compos. Struct. 80: 352–360. https://doi.org/10.1016/j.compstruct.2006.05.023.
Elrefai, A., J. West, and K. Soudki. 2012. “Fatigue of reinforced concrete beams strengthened with externally post-tensioned CFRP tendons.” Constr. Build. Mater. 29: 246–256. https://doi.org/10.1016/j.conbuildmat.2011.10.014.
Fang, Y., Z. Fang, R. Jiang, Y. Xiang, and D. Huang. 2019. “Transverse static and low-velocity impact behavior of CFRP wires under pretension.” J. Compos. Constr. 23 (5): 04019041. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000970.
Fang, Z., R. Hu, R. Jiang, Y. Xiang, and C. Liu. 2020. “Fatigue behavior of stirrup free reactive powder concrete beams prestressed with CFRP tendons.” J. Compos. Constr. 24 (4): 04020018. https://doi.org/10.1061/(ASCE)CC.1943-5614.0001027.
Fang, Z., Y. Xiang, K. Y. Zhang, and C. L. Wang. 2011. “The research to the fatigue properties of reactive powder concrete influenced by the steel fiber concrete.” J. Hunan Univ. 38 (6): 6–12.
FHWA (Federal Highway Administration). 2013. Design guide for precast UHPC waffle deck panel system, including connections. FHWA-HIF-13-032. Washington, DC: FHWA.
Ghallab, A., and A. W. Beeby. 2005. “Factors affecting the external prestressing stress in externally strengthened prestressed concrete beams.” Cem. Concr. Compos. 27 (9–10): 945–957. https://doi.org/10.1016/j.cemconcomp.2005.05.003.
Grace, N. F. 2000. “Response of continuous CFRP prestressed concrete bridges under static and repeated loadings.” PCI J. 45 (6): 84–102. https://doi.org/10.15554/pcij.11012000.84.102.
Graybeal, B., E. Brühwiler, B.-S. Kim, F. Toutlemonde, Y. L. Voo, and A. Zaghi. 2020. “International perspective on UHPC in bridge engineering.” J. Bridge Eng. 25: 04020094. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001630.
Jeong, Y., W. S. Kim, V. Gribniak, and D. Hui. 2019. “Fatigue behavior of concrete beams prestressed with partially bonded CFRP bars subjected to cyclic loads.” ACI Mater. J. 12: 3352.
Li, J., Z. Wu, C. Shi, Q. Yuan, and Z. Zhang. 2020. “Durability of ultra-high performance concrete - A review.” Constr. Build. Mater. 255: 119296. https://doi.org/10.1016/j.conbuildmat.2020.119296.
Lohaus, L., N. Oneschkow, and M. Wefer. 2012. “Design model for the fatigue behaviour of normal-strength, high-strength and ultra-high-strength concrete.” Struct. Concr. 13: 182–192. https://doi.org/10.1002/suco.201100054.
Lou, T., S. M. R. Lopes, and A. V. Lopes. 2014. “Factors affecting moment redistribution at ultimate in continuous beams prestressed with external CFRP tendons.” Composites, Part B 66: 136–146. https://doi.org/10.1016/j.compositesb.2014.05.007.
Luo, X., Z. Tan, Y. F. Chen, and Y. Wang. 2019. “Comparative study on fatigue behavior between unbonded prestressed and ordinary reinforced reactive powder concrete beams.” Mater. Test. 61 (4): 323–328. https://doi.org/10.3139/120.111323.
Mahmud, G. H., Z. Yang, and A. M. T. Hassan. 2013. “Experimental and numerical studies of size effects of ultra high performance steel fibre reinforced concrete (UHPFRC) beams.” Constr. Build. Mater. 48: 1027–1034. https://doi.org/10.1016/j.conbuildmat.2013.07.061.
Makita, T., and E. Bruehwiler. 2014. “Tensile fatigue behaviour of ultra-high performance fibre reinforced concrete combined with steel rebars (R-UHPFRC).” Int. J. Fatigue 59: 145–152. https://doi.org/10.1016/j.ijfatigue.2013.09.004.
Mohamed, M. A. 2016. “Flexural fatigue behavior of R. C. beams strengthened with externally prestressed CFRP.” IOSR-JMCE. 13 (1): 71–79.
Niu, Y., H. Huang, J. Wei, C. Jiao, and Q. Miao. 2022. “Investigation of fatigue crack propagation behavior in steel fiber-reinforced ultra-high-performance concrete (UHPC) under cyclic flexural loading.” Compos. Struct. 282: 115126. https://doi.org/10.1016/j.compstruct.2021.115126.
Ríos, J. D., H. Cifuentes, S. Blasón, M. López-Aenlle, and A. Martínez-De La Concha. 2021. “Flexural fatigue behaviour of a heated ultra-high-performance fibre-reinforced concrete.” Constr. Build. Mater. 276 (4): 122209. https://doi.org/10.1016/j.conbuildmat.2020.122209.
Saadatmanesh, H., and F. E. Tannous. 1999. “Relaxation, creep, and fatigue behavior of carbon fiber reinforced plastic tendons.” ACI Mater. J. 96 (2): 143–153.
Sawicki, B., and E. Brühwiler. 2021. “Fatigue resistance of reinforced UHPFRC beams.” Int. J. Fatigue 148: 106216. https://doi.org/10.1016/j.ijfatigue.2021.106216.
Wang, X., J. Shi, G. Wu, L. Yang, and Z. Wu. 2015a. “Effectiveness of basalt FRP tendons for strengthening of RC beams through the external prestressing technique.” Eng. Struct. 101: 34–44. https://doi.org/10.1016/j.engstruct.2015.06.052.
Wang, X., J. Shi, Z. Wu, and Z. Zhu. 2015b. “Fatigue behavior of basalt fiber-reinforced polymer tendons for prestressing applications.” J. Compos. Constr. 20 (3): 04015079. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000649.
Wang, Y., X. Shao, J. Cao, X. Zhao, and M. Qiu. 2021. “Static and fatigue flexural performance of ultra-high performance fiber reinforced concrete slabs.” Eng. Struct. 231: 111728. https://doi.org/10.1016/j.engstruct.2020.111728.
Xiang, Y., Z. Fang, and Y. Fang. 2017a. “Single and multiple impact behavior of CFRP cables under pretension.” Constr. Build. Mater. 140: 521–533. https://doi.org/10.1016/j.conbuildmat.2017.02.112.
Xiang, Y., Z. Fang, C. Wang, Y. Zhang, and Y. Fang. 2017b. “Experimental investigations on impact behavior of CFRP cables under pretension.” J. Compos. Constr. 21 (2): 04016087. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000745.
Xu, J., P. Zhu, Z. J. Ma, and W. Qu. 2019. “Fatigue flexural analysis of concrete beams reinforced with hybrid GFRP and steel bars.” Eng. Struct. 199: 109635. https://doi.org/10.1016/j.engstruct.2019.109635.
Xue, J., B. Briseghella, F. Huang, C. Nuti, H. Tabatabaic, and B. Chen. 2020. “Review of ultra-high performance concrete and its application in bridge engineering.” Constr. Build. Mater. 101: 902–917.
Yang, J., Z. Fang, and G. L. Dai. 2011. “Flexural behavior of prestressed UHPC beams.” Adv. Mater. Res. 243–249: 1145–1155.
Yoo, D.-Y., N. Banthia, and Y.-S. Yoon. 2016. “Predicting service deflection of ultra-high-performance fiber-reinforced concrete beams reinforced with GFRP bars.” Composites, Part B 99: 381–397. https://doi.org/10.1016/j.compositesb.2016.06.013.
Zhang, S., X. Shao, J. Cao, J. Cui, J. Hu, and L. Deng. 2016. “Fatigue performance of a lightweight composite bridge deck with open ribs.” J. Bridge Eng. 21 (7): 04016039. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000905.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Nov 12, 2021
Accepted: Jun 13, 2022
Published online: Aug 10, 2022
Published in print: Oct 1, 2022
Discussion open until: Jan 10, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Qizhi Xu, Yutong Zhu, Wendel Sebastian, Jingquan Wang, Effect of Steel-Fiber Shear Reinforcement on Postcracking Shear Fatigue Behavior of Nonstirrup UHPC Beams, Journal of Structural Engineering, 10.1061/JSENDH.STENG-12112, 150, 4, (2024).
- Jiaping Fu, Tian Zeng, Bing Wang, Ping Zhuge, Jiajun Xia, Wanyun Cai, The Interfacial Friction Loss of Prestressed Carbon-Fiber Tendons in a Bending State, Buildings, 10.3390/buildings13010099, 13, 1, (99), (2022).